PAC BKSUZK941 User manual

PAC
Brand
PAC
Model
BKSUZK941
Type
User manual

This manual is also suitable for

CUSTOMER HELP LINE
USA 800-323-4329 • Canada 800-245-8777
©2015 AMERICAN INTERNATIONAL INDUSTRIES, INC.
SUZK941 Mounting Kit
Chevrolet
2004-08 AVEO
2004-08 AVEO 5
2004-06 AVEO WAGON
Daewoo
1999-02 LANOS
1999-02 LEGANZA
1999-02 NUBIRA
Suzuki
2004-06 VERONA
2004-08 FORENZA
2005-08 RENO
VEHICLE APPLICATIONS
iSUZK941
TECH Ver. 5/12 PRINT Ver. 5/15
2500 East Francis Street Ontario, CA 91761, U.S.A.
USA Sales (800) 336-6500
Canada Sales (888) 922-3006
For information about other American International automotive
accessories visit our website at:
http://www.aius.net
Optional: ISO trim ring
may be used in place of
after-market radio’s trim ring.
1. Attach ISO mount brackets to
rear of kit as shown below and
attach to rear of pocket using
small screws provided with kit.
2. Insert ISO mountable radio
between ISO mount brackets
and loosely attach to sides of
radio using screws provided
with radio when possible
or screws supplied with kit.
3. Attach ISO trim ring to
face of kit.
4. Slide radio forward or
backward for desired look
and tighten screws.
1. Attach mounting brackets to rear of kit as shown below and attach to rear of pocket
using small screws provided with kit.
2. Insert DIN sleeve from your new radio into the opening of the installation kit.
3. Depress the tabs from inside the sleeves opening upward, outward, and
downward to secure sleeve to the installation kit.
INSERT SPACERS INTO
BRACKETS ON BOTH
SIDES ONLY WHEN ISO
MOUNTING RADIO
ISO
Trim Ring
(Use Optional)
IS
O T
rim
Rin
g
(Us
e
Op
tio
n
a
l)
DIN MOUNT INSTRUCTIONS
ISO MOUNT INSTRUCTIONS
Optional: ISO trim ring
may be used in place of
after-market radio’s trim ring.
NOTES:
1 6
1. Carefully unsnap the trim from around the Radio/ Heater A/C controls & remove.
2. Remove the (2) Phillips screws securing the radio to the sub dash.
3. Remove the radio from the dash cavity, disconnect the wire harness & antenna lead
& remove the radio.
DASH DISASSEMBLY INSTRUCTIONS
1
999-02 DAEWOO NUBIRA
REMOVE ALL SHADED
MOUNTING TABS ON BOTH
LEFT AND RIGHT BRACKETS
INSERT SPACERS INTO
BRACKETS ON BOTH SIDES ONLY
WHEN ISO MOUNTING RADIO
ISO
Tr
im
Ring
(Use Optional)
REMOVE ONLY LOWER HALF
OF MOUNTING TAB ON LEFT
& RIGHT BRACKETS
1. Carefully pry radio trim bezel outward to remove.
2. Remove the (4) screws securing the radio to the sub-dash.
3. Pull radio forward, disconnect the wire harness and antenna lead and remove radio.
REMOVE ALL SHADED AREAS
ON BOTH LEFT AND
RIGHT BRACKETS
INSERT SPACERS INTO
BRACKETS ON BOTH SIDES ONLY
WHEN ISO MOUNTING RADIO
ISO
Trim Ring
(Use Optional)
1. Starting at the bottom, carefully pry outward and remove the Dash trims from each
side of the radio and climate controls.
2. Remove the (4) Phillips screws securing the factory radio to the sub-dash.
3. Carefully pull radio forward, disconnect the wire harness and antenna
lead from radio and remove radio.
DO NOT REMOVE REAR
MOUNTING TAB
DASH DISASSEMBLY INSTRUCTIONS
2
004-08 CHEVROLET AVEO/AVEO 5/AVEO WAGON (Excluding LT models)
DASH DISASSEMBLY INSTRUCTIONS
2004-06 SUZUKI VERONA
5 2
1. From below the glove box, remove the (2) phillips screws at the bottom
of the glove box.
2. Remove the (3) Phillips screws securing the top of the glove box housing frame and
remove glove box assembly.
3. Inside the glove box area on the left is a climate control cable that is attached with a
plastic clamp (Be sure you remember how you removed it so you will be able to
re-attach it when re-assembling the vehicle). Unfasten the cable clamp and unhook
the cable from the Heater control gear.
4. From under the driverʼs side dash, unfasten the single climate control cable
(same removal instructions as in step 3 above).
5. Starting from the bottom of the climate control/dash trim bezel, carefully pry outward
to release the (6) trim bezel clips and pull trim bezel forward.
6. Disconnect all harnesses from the rear of the climate controls and trim bezel and
remove bezel (Make sure you look to see how the (2) climate control cables were
routed for dash re-assembly).
7. Remove the (4) Phillips screws securing the radio or radio & pocket to the sub-dash.
8. Pull radio forward, disconnect the wire harness and antenna lead and remove radio.
REMOVE ALL SHADED
AREAS ON BOTH LEFT
AND RIGHT BRACKETS
INSERT SPACERS
INTO BRACKETS
ON BOTH SIDES
ONLY WHEN ISO
MOUNTING RADIO
ISO Trim
Ring
(Use Optional)
1. Carefully unsnap the trim from around the radio & remove.
2. Remove the (2) Phillips screws securing the radio to the sub dash.
3. Remove the radio from the dash cavity, disconnect the wire harness &
antenna lead & remove the radio.
REMOVE ALL SHADED
MOUNTING TABS ON
BOTH LEFT AND
RIGHT BRACKETS
REMOVE ONLY UPPER HALF
OF MOUNTING TAB ON LEFT
& RIGHT BRACKETS
INSERT SPACERS INTO
BRACKETS ON BOTH SIDES ONLY
WHEN ISO MOUNTING RADIO
ISO
Trim Ring
(Use Optional)
DASH DISASSEMBLY INSTRUCTIONS
2
004-08 SUZUKI FORENZA/2005-08 SUZUKI RENO
DASH DISASSEMBLY INSTRUCTIONS
1
999-02 DAEWOO LANOS & LEGANZA
3 4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

PAC BKSUZK941 User manual

PAC
Brand
PAC
Model
BKSUZK941
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents