ESAB WC-7C PREST-O-WELD Radiator Coolant Circulator Troubleshooting instruction

INSTRUCTIONS for

F15-138-F

September, 2009

Figure - 1. Mounting Dimensions

• Electricshockcankill.

• Hotliquidsorvaporscanburnyou.

• Breathingmistorvaporsofethylene-glycolcan

poisonyou.

• Burstinghosesorpowercablescanexposeper-

sonstothesehazards.

• Donotoperatewithequipmentrequiringcool-

ingcapacityor owratesexceeding the rated

valuesforthiscoolantcirculator.

• Theseinstructionsareforexperiencedoperators.

Ifyouarenotfullyfamiliarwiththeprinciplesof

operationandsafepracticesforweldingequip-

ment,werecommendthatyoureadourbooklet,

”PrecautionsandSafePracticesforArcWelding,

Cutting,andGouging”,Form52-529.

• Donotattempttomaintainorusethisunituntil

you have read andunderstand these instruc-

tions.Donotpermituntrainedpersonstouseor

maintainthisunit.Ifyoudonotfullyunderstand

these instructions, contact your supplier for

furtherinformation.

1.69"

3.42"

14.78"

19.50"

3.42"

0.219" dia. hole, typ. 8 places

These instructions provide installation, operation, service

and parts information for the WC-7C Radiator Coolant

Circulator. This unit recirculates coolant to cool electric arc

cutting and welding equipment.

INSTALLATION

Install the WC-7C in an appropriate location so as to main-

tain adequate and unrestricted airow into and out of the

cabinetry. For permanent mounting refer to Figure-1 for

mounting hole dimensions in the base of this unit.

WC-7C

RADIATORCOOLANTCIRCULATOR

P/N 33859 - Valid Serial No. WxxJ348xxx and above

SPECIFICATIONS

Dimensions: 31.50" high (80cm) x 21.50" wide (54.6cm) x 25.00 deep (63.5cm)

Weight: 215 lb. dry (97.5kg)/ 249 lb. wet (133kg)

PumpType: Positive displacement, rotary vane type with adjustable by-pass valve (200 psi/13.8 bars max.), CW rotation

as viewed from nameplate.

RadiatorType: Copper tubing, aluminum nned air-to-water type with galvanized steel frame.

50Hz,1PhaseInputPower 60Hz,1PhaseInputPower

ACInputVoltages 200/230/400/460/575V., +/- 10%

ACInputAmperage 9/8/5/4/3 Amperes

PumpCapacity 1.95 gpm at 100 psi 2.33 gpm at 100 psi

(7.4 l/min at 6.9 bars) (8.8 l/min at 6.9 bars)

CoolingCapacity@2gpm 23,100 BTU/hr. (6800 watts) 27,720 BTU/hr. (8120 watts)

at45° F(7°C)temperaturedierencebetweenhighcoolanttemperatureandambientairtemperature.

Max.DeliveryPressure 160 psig (11 bars)

ReservoirCapacity 4 gallons (15.2 liters)

Besurethisinformationreachestheoperator.Youcan

getextracopiesthroughyoursupplier.

WARNING

1.69"

3.42"

14.78"

19.50"

8 x Dia. 0.219"

InputPowerConnections

If the power cable supplied with the circulator is missing,

a 3-conductor power cable suitable to meet the required

input power must be installed. The cable must have 1/4"

ring lugs installed on the machine end. Connect the power

leads to the L1 and L2 terminals on TB1 Input Power Terminal

Board and the ground lead to the ground lug on the base

of the machine. A strain relief tting is provided to feed a

power cable through the rear panel of the cabinet. Refer to

Figure-2 Schematic Diagram for proper Input Voltage Link

placement, Figure-2 shows link in place for 575 volt input.

Electrical installation must be in accordance with local

electrical codes for this type of equipment.

NOTE:

Motor ( M2 ) Is shipped from supplier wired for 115 VAC.

Wiring must be re-congured to use with 230 VAC. See

wiring information panel on motor for proper 230 VAC

wiring conguration.

ControlConnections

A 3-pin receptacle P1 is provided on the rear panel to supply

the WC-7C with 115 Vac control voltage for pump motor

contactor control. The WC-7C must be supplied with this

control voltage in order for the pump to operate. Order

Part No. 13734546; 3-Pin Female Plug and Part No. 182W61;

Cable Clamp for Plug to make a control cable using a two

conductor cable. Solder the leads of this cable to Pins A and

B of the Plug and connect to control voltage device. Pump

motor contactor control is supplied so as to not operate

pump when cooling is not needed. Donotintermittently

operate the pump motor as this will cause needless

weartothepump.

CoolantConnections

These connectors are located on the front of the unit and are

marked “IN” and “OUT”. Connect the hoses to the WC-7C ac-

cordingly. The torch hose ends should be tted with 5/8"-18

Male L.H. Air/Water hose (CGA-033) connectors.

Do not connect hoses to a solenoid valve that can be

closed when the pump is operating as damage to pump

can result.

With the torch and the WC-7C connected, ll the reservoir

with the specially formulated torch coolant (order part no.

156F05). Do not use regular anti-freeze solutions, such as

for an automobile, as the additives will harm the pump

and torch.

After lling the reservoir to the MAX mark, located on the

front panel, run the pump with its cap removed in order to

purge air from the radiator, hoses, and torch. Re-check cool-

ant level to ensure reservoir is lled to MAX mark. Replace

reservoir cap after purging and checking coolant level.

Figure-2.WC-7CSchematicandInputPowerTerminalBoard

4460

230200

575

DANGER

HIGH

VOLTAGE

115 VAC

INPUT

INPUT POWER

AUX

COOLER

400

1 543

GND1

200V

575V

460V

400V

TB1

230V

TB1

GND3

PL2

TB1

TS1

PL3

115

VAC

INPUT

200/230/400/460/575

VOLTS 50/60Hz

1 PHASE W/ GND

PL2

M1 M2

2 2

10A

SINGLE PHASE 50/60 Hz

VOLTAGE CURRENT

200 VAC 9 AMPS

230 VAC 8 AMPS

400 VAC 5 AMPS

460 VAC 4 AMPS

575 VAC 3 AMPS

COMPONENT LEGEND

LOCATION ITEM

REF. REF. DESCRIPTION

B-4 F1 FUSE, 10 AMP

B-4 F2 FUSE, 10 AMP

A-5 K1 PUMP MOTOR CONTACTOR

A-5 M1 FAN MOTOR

A-5 M2 PUMP MOTOR

A-1 P1 PUMP MOTOR CONTACTOR PLUG

D-4 PL1 MAIN POWER "ON" LIGHT

A-3 PL2 PUMP "ON" LIGHT

A-2 PL3 PUMP OVER-TEMP LIGHT

B-4 T1 AUTO-TRANSFORMER

B-2 TB1 TERMINAL BOARD, INPUT POWER

A-2 TS1 PUMP OVER-TEMP THERMAL SWITCH

230VAC-seenoteabove

PumpPressureAdjustment

Pump pressure is pre-set at the factory for 130 P.S.I., output

coolant pressure may be adjusted by opening or closing

the by-pass valve on the pump. The by-pass valve adjust-

ment screw is located under the large acorn nut on the

pump body. Pressure can be increased by turning the screw

clockwise and decreased by turning the screw counter-

clockwise. When replacing acorn nut and gasket, tighten

rmly to prevent air from being sucked into pump. Do not

exceedtherecommendeddeliverypressurestotorches

asoutlinedbythemanufacturer!

Do not operate the pump into a closed discharge line. If

operated for more than a few minutes against a closed dis-

charge, the resulting heat build-up will cause rapid wear of

the mechanical seal and eventual seizure and failure of the

pump. A thermostat will stop the pump motor if the pump

temperature goes over 131 deg. F.

Be careful not to touch the pump motor when adjusting

pump pressure as it can get very hot, up to 100 deg. F. above

ambient temperature.

MAINTENANCE

Electricshockcankill.Precautionarymeasuresshould

be taken to provide maximum protection against

electricalshock.Besurethatallprimarypowertothe

machinehasbeenexternallydisconnected.Openwall

disconnect switch or circuitbreaker before attempt-

inginspectionorworkinsidethecirculator.Installall

coversaftercompletingservice.Do notoperate unit

withoutcovers.

Ifthisequipmentdoesnotoperateproperly,stopwork

immediatelyandinvestigatethecauseofthemalfunc-

tion. Maintenance work must be performed by an

experiencedperson, andelectrical workby atrained

electrician.Donotpermituntrainedpersonstoinspect,

clean,orrepairthisequipment.Useonlyrecommended

replacementparts.

1. Maintain the coolant level within 1/2" of the MAX

mark on the reservoir sight gauge located on the front

panel.

2. Periodically check the coolant pressure and flow

through the system.

3. Periodically inspect the radiators for build-up of

airborne dust or other residues that may hinder the

cooling capacity of the WC-7C.

4. When tightening ttings, use wrench on both male and

female tting to prevent damage to ttings or plumb-

ing.

5. When draining old coolant, dispose of it according to

your local applicable rules and ordinances.

6. Oil pump motor shaft bearings once a year with 30

drops SAE 10 motor oil. The pump bearings are self

lubricating and require no further lubrication.

TROUBLESHOOTING

1. PumpBelowCapacity- Can be caused by restricted

inlet, wrong direction of rotation, low motor R.P.M., and

the relief valve improperly adjusted.

2. Pump Noisy - Can be caused by restricted inlet,

discharge pressure over 200 P.S.I., loose acorn nut or

damaged acorn nut gasket, air getting into lines, loose

couplings, misalignment between pump and motor,

and loose mounting bolts or clamping ring.

3. Leakage- Is caused by failing mechanical shaft seal or

rubber O-rings. Arrange to have pump rebuilt.

4. PumpTurnsHard- Can be caused by misalignment

between pump and motor or by lime and mineral de-

posits in the pump. Deposits in pump would necessitate

a pump rebuild, arrange to have pump rebuilt at pump

service center.

5. Donotdisassemblepump! Any attempt at eld repair

will void the warranty.

6. PumpMotorNotTurning- If PL2 not lit, 115VAC may

not be supplied to P1, or TS1 is over 131 deg. F if PL3 is

lit. If PL1 and PL2 are lit, check F1 and F2.

7. FanMotorNotTurning- Check F1 and F2. Neither M1

fan motor nor M2 pump motor will run with F1 or F2

blown.

8. Pump/MotorVibration - Indicates wear on coupling.

Replace with P/N 951841 coupling.

WARNING

PUMPSERVICECENTERS

Arrange to have the pump serviced, when necessary at

one of the following service centers. Rebuilt and exchange

pumps as well as new pumps carry a one year manufac-

turer’s warranty. (Pump: Procon Model CB 2503XL)

IntheU.S.A.:

PROCONPRODUCTS(Manufacturer)

910 Ridgely Road

Murfreesboro, TN 37130

Ph. no. (615) 890-5710

Halsted & Hoggan Inc.

935 Santa Fe Ave.

Los Angeles, CA90021

Ph. no. (213) 623-1248

Foxx Equipment Co.

955 Decatur, Unit B

Denver, CO 80204

Ph. no. (303) 573-1766

American Beverage Equipment Co.

27560 Groesbeck Hwy.

Roseville, MI 48066

Ph. no. (313) 773-0094

Foxx Equipment Co.

421 Southwest Blvd.

Kansas Clity, MO 64108

Ph. no. (816) 421-3600

Chudnow Mfg. Co. Inc.

3055 New Street

Oceanside, NY 11572

Ph. no. (516) 593-4222

Northlake Supply Co.

1347 Manufacturing Street

Dallas, TX 75207

Ph. no. (214) 653-8381

Southwest Bottlers

1360 Presidential Drive

Suite 120

Richardson, TX 75081

Ph. no. (214) 235-8768

Restaurant Appliance Service

7219 Roosevelt Way NE

Seattle, WA 98115

Ph. no. (206) 524-8200

REPAIRPARTS

The following illustrations of the WC-7C identies replace-

ment parts by item number as tabulated in the related parts

list. The list identies each part by stock number, the total

quantity used, schematic references when applicable, and

description of the part.

Figure-3, on the next page, depicts the repair parts avail-

able for this unit. If a part you require is not shown in the

illustration, it may be ordered as a request item. See below

directions to insure you will have all information required

to identify the parts you may require.

REPAIRPARTSORDERINGINFORMATION

To assure proper operation, it is recommended that only

Genuine ESAB Parts be used to repair this equipment

(other than pump). To order replacement parts from your

supplier:

A. Give stock number, serial number, descriptlion and

quantity of each part required.

B. Give stock number and description of equipment on

which the parts are to be used.

C. Indicate any special shipping instructions.

InAUSTRALIA

Roehlen Industries Pty. Ltd.

P.O Box 354

Mordialloc, Victoria 3195

Ph. no. 61 (3) 580-4155

Fax no. 61 (3) 580-2954

InJAPAN

Nippon Oil Pump Co. Ltd.

1 Chorne No. 8-2, Horinouchi

Suginami-Ku, Tokyo

Ph. no. 81-03 (313) 7521

Fax no. 81-03 (313) 2188

InGERMANY

Standex International GmbH

Postfach 130665

4150 Krefeld (formerly W. Germany)

Ph. no 49 (2151) 371224

Fax no. 49 (2151) 371258

Figure-3.WC-7CReplacementPartsIllustration.Refertonextpageforstocknos.ofparts.

460

230200

575

DANGER

HIGH

VOLTAGE

115 VAC

INPUT

INPUT POWER

AUX

COOLER

400

18 20

SEE DETAIL "C"

REPAIRPARTSLISTINGforWC-7C(RefertoFigure-3.)

 ITEM SCHEM. QTY. STOCK DESCRIPTION

 NO. REF. USED NO.

1 M1 1 2062334 FAN MOTOR, 230VAC, 1/3 HP.

2 1 673676 FAN BLADE 16"

3 10 13734871 HOSE CLAMP 5/8"

4 AR 90858009 TUBING 3/8" X 5/8"

5 4 13735961 RADIATOR CORE

8 GND1, 2 2 2057726 GND. TERMINAL LUG

9 1 598481 ** PRESSURE GAUGE, 200 PSI

1 0558004488 ** PRESSURE GAUGE, 200 PSI

10 2 58V75 “B” AIR/WATER L.H. BKHD. FITTING

11 1 950518 GROMMET, 2"

12 PL3 1 598227 INDICATOR LIGHT

13 PL1, 2 2 634716 INDICATOR LIGHT

14 1 948377 KNOB, KNURLED

15 1 0558007638 PUMP

16 M2 1 951269 PUMP MOTOR, 115/230VAC, 1/2HP.

17 2 672065 TERMINAL STRAP, COPPER

18 2 639514 FUSE MOUNT

19 1 34089B FUSE PLATE

20 2 951201 FUSE, SLO-BLOW, 10A., 250VAC

21 1 951068 CLAMP, V-BAND, PUMP

22 2 182W82 ELBOW, 1/4 NPT M-F, BRASS

23 3 10Z30 CONN., 1/4MNPT-5/8MNPT

24 1 68161103 TEE CONNECTOR

25 2 950178 REDUCER, 1/2NPT FEM.

26 TS1 1 950710 SWITCH, THERMAL 131 DEG. F.

27 P1 1 13734545 RECEPTACLE, 3 PIN, MALE

P1 1 13734546 PLUG, 3 PIN, FEM., MATES w/ITEM-27

P1 1 182W61 CLAMP FOR 13734546

28 2 180W38 STRAIN RELIEF

29 T1 1 33927 AUTO-TRANSFORMER, 50/60 HZ.

30 K1 1 672162 RELAY, 3 POLE, 120VAC

31 TB1 1 32095 TERMINAL BOARD, PRINTED

32 13 680510 TERMINAL STUD, 1/4", BRASS

34 1 950156 DUST CAP

35 1 951841 COUPLING PIECE (PKG. OF 5)

36 1 951478 * TANK COMPLETE WITH CAP

*Cap not available separately.

** Refer to console serial number to determine which gauge to order. Gauges require dierent hole sizes in front panel

and are not interchangeable. Console with serial number in PxxJ348xx format requires gauge P/N 0558004488. All others

use P/N 598481.

RevisionHistory

December, 2007 Revision - Added French language per Alaaeldin Assal request.

September, 2009 Revision - Added 230 VAC note under subsection Input Power Connections per inputs from G. Cole.

F15-138-F 09/2009

A. CUSTOMER SERVICE QUESTIONS:

Telephone: (800)362-7080 / Fax: (800) 634-7548 Hours: 8:00 AM to 7:00 PM EST

Order Entry Product Availability Pricing Order Information Returns

B. ENGINEERING SERVICE:

Telephone: (843) 664-4416 / Fax : (800) 446-5693 Hours: 7:30 AM to 5:00 PM EST

Warranty Returns Authorized Repair Stations Welding Equipment Troubleshooting

C. TECHNICAL SERVICE:

Telephone: (800) ESAB-123/ Fax: (843) 664-4452 Hours: 8:00 AM to 5:00 PM EST

Part Numbers Technical Applications Specications Equipment Recommendations

D. LITERATURE REQUESTS:

Telephone: (843) 664-5562 / Fax: (843) 664-5548 Hours: 7:30 AM to 4:00 PM EST

E. WELDING EQUIPMENT REPAIRS:

Telephone: (843) 664-4487 / Fax: (843) 664-5557 Hours: 7:30 AM to 3:30 PM EST

Repair Estimates Repair Status

F. WELDING EQUIPMENT TRAINING

Telephone: (843)664-4428 / Fax: (843) 679-5864 Hours: 7:30 AM to 4:00 PM EST

Training School Information and Registrations

G. WELDING PROCESS ASSISTANCE:

Telephone: (800) ESAB-123 Hours: 7:30 AM to 4:00 PM EST

H. TECHNICAL ASST. CONSUMABLES:

Telephone : (800) 933-7070 Hours: 7:30 AM to 5:00 PM EST

IFYOUDONOTKNOWWHOMTOCALL

Telephone: (800) ESAB-123

Fax: (843) 664-4462

Hours: 7:30 AM to 5:00 PM EST

visit us on the web at http://www.esabna.com

The ESAB web site oers

Comprehensive Product Information

Material Safety Data Sheets

Warranty Registration

Instruction Literature Download Library

Distributor Locator

Global Company Information

Press Releases

Customer Feedback & Support

ESABWelding&CuttingProducts,Florence,SCWeldingEquipment

COMMUNICATIONGUIDE-CUSTOMERSERVICES

Page is loading ...

CENTRESD’ENTRETIENPOURPOMPE

Contactez l’un des services de réparation suivants pour

qu’ils effectuent les opérations d’entretien sur la pompe.

Les pompes reconstruites et de rechange ainsi que les

nouvelles pompes disposent d’une garantie du fabricant

d’un an. (Pompe : Procon Modèle CB 2503XL)

AuxÉtats-Unis:

PROCONPRODUCTS(fabricant)

910 Ridgely Road

Murfreesboro, TN 37130 U.S.A.

Tél : +1 (615) 890-5710

Halsted & Hoggan Inc.

935 Santa Fe Ave.

Los Angeles, CA 90021 U.S.A.

Tél : +1 (213) 623-1248

Foxx Equipment Co.

955 Decatur, Unit B

Denver, CO 80204 U.S.A.

Tél : +1 (303) 573-1766

American Beverage Equipment Co.

27560 Groesbeck Hwy.

Roseville, MI 48066 U.S.A.

Tél : +1 (313) 773-0094

Foxx Equipment Co.

421 Southwest Blvd.

Kansas Clity, MO 64108 U.S.A.

Tél : +1 (816) 421-3600

Chudnow Mfg. Co. Inc.

3055 New Street

Oceanside, NY 11572 U.S.A.

Tél : +1 (516) 593-4222

Northlake Supply Co.

1347 Manufacturing Street

Dallas, TX 75207 U.S.A.

Tél : +1 (214) 653-8381

Southwest Bottlers

1360 Presidential Drive

Suite 120

Richardson, TX 75081 U.S.A.

Tél : +1 (214) 235-8768

Restaurant Appliance Service

7219 Roosevelt Way NE

Seattle, WA 98115 U.S.A.

Tél : +1 (206) 524-8200

PIÈCESDERÉPARATION

Les illustrations suivantes du WC-7C identie les pièces

de rechange par référence telles que stipulées dans

la liste des pièces de rechange connexes. La liste

identie chaque pièce par réf. de stock, la quantité totale

utilisée, les références des diagrammes schématiques

si applicable et la description de la pièce.

La Figure-3, sur la page suivante décrit les pièces de

rechange disponible pour cette unité. Si vous avez

besoin d’une pièce qui ne gurerait pas sur l’illustration,

vous pouvez la commander séparément. Voustrouverez

ci-dessous des instructions permettant de garantir

que tous disposez de toutes les informations requises

à l’identification des pièces dont vous pourriez

avoir besoin.

INFORMATIONSSURLACOMMANDEDE

PIÈCESDERECHANGE

Pour garantir un bon fonctionnement, il est recommandé

d’utiliser uniquement des pièces ESAB authentiques

pour réparer cet équipement (autre que la pompe).

Pour commander des pièces de rechange auprès de

votre fournisseur :

A. Communiquez le numéro du stock, de la série, une

description et la quantité de chaque pièce que vous

voulez commander.

B. Communiquez le numéro du stock et la description de

l’équipement sur lequel les pièces seront utilisées.

C. Indiquez toute instruction spéciale pour l’expédition.

EnAUSTRALIE

Roehlen Industries Pty. Ltd.

P.O Box 354

Mordialloc, Victoria 3195 U.S.A.

Tél : 61 (3) 580-4155

Fax : 61 (3) 580-2954

AuJAPON

Nippon Oil Pump Co. Ltd.

1 Chorne No. 8-2, Horinouchi

Suginami-Ku, Tokyo Japan

Tél : 81-03 (313) 7521

Tél : 81-03 (313) 2188

EnALLEMAGNE

Standex International GmbH

Postfach 130665

4150 Krefeld (anciennement Allemagne de l’Ouest)

Tél : 49 (2151) 371224

Fax : 49 (2151) 371258

Page is loading ...

LISTEDESPIÈCESDERECHANGEPOURLEWC-7C(voirlaFigure-3)

 № RÉF. QTÉ № DESCRIPTION

 ÉLT SCHÉMA UTILISÉE STOCK

1 M1 1 2062334 MOTEUR VENTILATEUR, 230 VCA, 1/3 HP.

2 1 673676 LAME VENTIL 16 PO

3 10 13734871 SERRE-TUYAU 5/8 PO

4 AR 90858009 TUBE 3/8 X 5/8 PO

5 4 13735961 FAISCEAU RADIATEUR

8 GND1, 2 2 2057726 COSSE MASSE

9 1 598481 ** JAUGE DE PRESSION, 200 PSI

1 0558004488 ** JAUGE DE PRESSION, 200 PSI

10 2 58V75 B RACCORD G ARR AIR/EAU

11 1 950518 ŒILLET, 2 PO

12 PL3 1 598227 TÉMOIN

13 PL1, 2 2 634716 TÉMOIN

14 1 948377 BOUTON, MOLETÉ

15 1 0558007638 POMPE

16 M2 1 951269 MOTEUR POMPE, 115/230 VCA, 1/2 HP.

17 2 672065 BORNIER, CUIVRE

18 2 639514 MONTAGE FUSIBLE

19 1 34089B PLAQUE FUSIBLE

20 2 951201 FUSIBLE, FUSION LENTE, 10A, 250VCA

21 1 951068 CLAMP, BANDE V, POMPE

22 2 182W82 COUDE, 1/4 NPT M-F, LAITON

23 3 10Z30 CONN., 1/4 MNPT-5/8 MNPT

24 1 68161103 CONNECTEUR EN T

25 2 950178 RÉDUCTEUR, 1/2 NTP F

26 TS1 1 950710 INTERRUPTEUR, THERM 131 DEG. F.

27 P1 1 13734545 RÉCEPTACLE, 3 BROCHES, M

P1 1 13734546 FICHE, FEM., 3 BROCHES, S’ACCOUPLE

À L’ÉLÉMENT 27

P1 1 182W61 CLAME POUR 13734546

28 2 180W38 SERRE-CABLE

29 T1 1 33927 AUTO-TRANSFORMATEUR, 50/60 HZ.

30 K1 1 672162 RELAIS, TRIPOLAIRE, 120VCA

31 TB1 1 32095 BORNIER, CARTE IMPRIMÉE

32 13 680510 GOUJON BORNE, 1/4 PO, LAITON

34 1 950156 CACHE POUSSIÈRE

35 1 951841 PIÈCES ACCOUPL (PQT DE 5)

36 1 951478 * RÉSERVOIR COMPLET AVEC CAPOT

* Les capots ne sont pas vendus séparément.

** Voir le numéro de série de la console pour déterminer la jauge à commander. Les jauges requièrent différentes

tailles de trou dans le panneau avant et ne sont pas interchangeables. La console avec le numéro de série au

format PxxJ348xx requiert la jauge Réf. 0558004488. Toutes les autres se servent de la Réf. 598481.

RevisionHistory

December, 2007 Revision - Added French language per Alaaeldin Assal request.

September, 2009 Revision - Added 230 VAC note under subsection Input Power Connections per inputs from G. Cole.

F15-138-F 09/2009

A. CUSTOMER SERVICE QUESTIONS:

Telephone: (800)362-7080 / Fax: (800) 634-7548 Hours: 8:00 AM to 7:00 PM EST

Order Entry Product Availability Pricing Order Information Returns

B. ENGINEERING SERVICE:

Telephone: (843) 664-4416 / Fax : (800) 446-5693 Hours: 7:30 AM to 5:00 PM EST

Warranty Returns Authorized Repair Stations Welding Equipment Troubleshooting

C. TECHNICAL SERVICE:

Telephone: (800) ESAB-123/ Fax: (843) 664-4452 Hours: 8:00 AM to 5:00 PM EST

Part Numbers Technical Applications Specications Equipment Recommendations

D. LITERATURE REQUESTS:

Telephone: (843) 664-5562 / Fax: (843) 664-5548 Hours: 7:30 AM to 4:00 PM EST

E. WELDING EQUIPMENT REPAIRS:

Telephone: (843) 664-4487 / Fax: (843) 664-5557 Hours: 7:30 AM to 3:30 PM EST

Repair Estimates Repair Status

F. WELDING EQUIPMENT TRAINING

Telephone: (843)664-4428 / Fax: (843) 679-5864 Hours: 7:30 AM to 4:00 PM EST

Training School Information and Registrations

G. WELDING PROCESS ASSISTANCE:

Telephone: (800) ESAB-123 Hours: 7:30 AM to 4:00 PM EST

H. TECHNICAL ASST. CONSUMABLES:

Telephone : (800) 933-7070 Hours: 7:30 AM to 5:00 PM EST

IFYOUDONOTKNOWWHOMTOCALL

Telephone: (800) ESAB-123

Fax: (843) 664-4462

Hours: 7:30 AM to 5:00 PM EST

visit us on the web at http://www.esabna.com

The ESAB web site oers

Comprehensive Product Information

Material Safety Data Sheets

Warranty Registration

Instruction Literature Download Library

Distributor Locator

Global Company Information

Press Releases

Customer Feedback & Support

ESABWelding&CuttingProducts,Florence,SCWeldingEquipment

COMMUNICATIONGUIDE-CUSTOMERSERVICES

ESAB WC-7C PREST-O-WELD Radiator Coolant Circulator Troubleshooting instruction

Related papers

Other documents