Canned cycles (·M· model).
Quercus
CNC 8060
CNC 8065
·4·
REF. 2005
CHAPTER 5 CANNED CYCLES OF THE EDITOR. Z AXIS MACHINING.
5.1 Center punching. ........................................................................................................ 104
5.1.1 Basic operation. ....................................................................................................... 105
5.2 Drilling. ........................................................................................................................ 106
5.2.1 Basic operation. ....................................................................................................... 107
5.3 Deep hole drilling. ....................................................................................................... 108
5.3.1 Basic operation. ....................................................................................................... 110
5.4 Bore milling. ................................................................................................................. 111
5.4.1 Basic operation. ....................................................................................................... 112
5.5 Tapping. ...................................................................................................................... 113
5.5.1 Basic operation. ....................................................................................................... 115
5.6 Thread milling. ............................................................................................................ 116
5.6.1 Basic operation. ....................................................................................................... 118
5.7 Reaming. .................................................................................................................... 119
5.7.1 Basic operation. ....................................................................................................... 120
5.8 Boring. ........................................................................................................................ 121
5.8.1 Basic operation. ....................................................................................................... 122
5.9 Boring with spindle orientation. ................................................................................... 123
5.9.1 Basic operation. ....................................................................................................... 125
CHAPTER 6 CANNED CYCLES OF THE EDITOR. POCKETS / BOSSES.
6.1 Simple rectangular pocket. .......................................................................................... 128
6.1.1 Basic operation. ....................................................................................................... 131
6.2 Rectangular pocket with rounding. .............................................................................. 132
6.2.1 Basic operation. ....................................................................................................... 136
6.3 Circular pocket. ........................................................................................................... 137
6.3.1 Basic operation. ....................................................................................................... 141
6.4 Pre-emptied circular pocket. ....................................................................................... 142
6.4.1 Basic operation. ....................................................................................................... 145
6.5 Rectangular boss......................................................................................................... 147
6.5.1 Basic operation. ....................................................................................................... 151
6.6 Circular boss. .............................................................................................................. 152
6.6.1 Basic operation. ....................................................................................................... 155
CHAPTER 7 CANNED CYCLES OF THE EDITOR. 2D/3D PROFILE POCKETS.
7.1 2D profile pocket. ........................................................................................................ 158
7.1.1 Executable pocket file .............................................................................................. 162
7.1.2 Basic operation. ....................................................................................................... 163
7.1.3 Examples of how to define 2D profiles..................................................................... 164
7.2 3D profile pocket with islands. .................................................................................... 167
7.2.1 Executable pocket file .............................................................................................. 173
7.2.2 Basic operation. ....................................................................................................... 174
7.2.3 Examples of how to define 3D profiles..................................................................... 175
CHAPTER 8 CANNED CYCLES OF THE EDITOR. ROUGHING.
8.1 Surface milling. ............................................................................................................ 180
8.1.1 Basic operation. ....................................................................................................... 183
8.2 Point-to-point profile milling. ........................................................................................ 184
8.2.1 Basic operation. ....................................................................................................... 187
8.3 Free profile milling. ...................................................................................................... 188
8.3.1 Basic operation. ....................................................................................................... 191
8.4 Slot milling. .................................................................................................................. 192
8.4.1 Basic operation. ....................................................................................................... 196
CHAPTER 9 CANNED CYCLES OF THE EDITOR. MULTIPLE POSITIONING.
9.1 Multiple machining in straight line................................................................................ 200
9.1.1 Programming example............................................................................................. 201
9.2 Multiple machining in arc pattern. ................................................................................ 202
9.2.1 Programming example............................................................................................. 204
9.3 Multiple machining in rectangular pattern. ................................................................... 205
9.3.1 Programming example............................................................................................. 206
9.4 Multiple machining in grid pattern. ............................................................................... 207
9.4.1 Programming example............................................................................................. 208
9.5 Random multiple machining. ....................................................................................... 209
9.5.1 Programming example............................................................................................. 209
CHAPTER 10 USER CYCLES.