Schick Handel DMR18 User manual

DMR18

User Manual

Door Station

Please read this manual carefully before using the product you purchase, and keep it well for future

use.We reserve the right to modify the specication in this manual at any time without notice.

1 2 3

654

7 8 9

#0

*

RF CARD

1.Parts and Functions

2. Terminal Descriptions

Camera Lens

Night View LED

Speaker

Adjustable Camera

Connectiong Port

With rainy cover

350 mm

128 mm

1 2 3

654

7 8 9

#0

*

RF CARD

LCD Screen

ID Card Window

Digital Keypad

Microphone

12

3

L1

T/R -

CN-LK

T/R+

J/KMB JP-LK

Bus

SD Card Slot

EB+

EB-

N.O

LK+

LK-

+12V

L2

1 2 3

654

7 8 9

#0

*

RF CARD

12

3

12

3

•

+12V:

12VDCpoweroutput.

•

LK-(GND):

powerground.

•

LK+(COM):

commoncontactoftheRelay.

•

NO.:

normallyopencontactoftheRelay(refertoDTtechnicalguideforLockconnection

detailinformations).

•

EB+:

Exitbuttonconnectionport.

•

EB-:

Exitbutonconnectionport.

•

JP-LK:

Forelectroniclocksafetytypesetting(refertoDoorStationLockConnections).

•

T/R-:

USB-RS485communicationterminalnegative.

•

T/R+:

USB-RS485communicationterninalpositive.

•

Bus(

L1,L2

):

non-polaritybusline.

3.Door Station Mounting

1 2 3

4

7

5 6

Drill a hole and attach the

rainy cover to it

Attach screws to fix the

metal box

Attach the unit to the rainy

cover correctlly

Attach the baffle to protect

the unit from droping

The last view for all mounting

The view for rainy

cover after mounted

Adjust the camera angle and attach the

metal to the panel and wire correctly.

Camera

angle

4. Door Lock Connections

1. Internal Power Supply Mode

Use the powerofthesystemto supplyfortheelectroniclock,so thatthelockcanbe

connectedtothedoorstationdirectly,withoutanadditionalpowersupplyfortheelectroniclock.

Notethatthedoorstationcanonlyoutput12Vdcpower,thereforethekindoflockislimited.

• Theratedpowerofthelockmustbelessthan12Vdc300mAwhenusinginternalpower

supplymode

• TheGNDmustconnecttothenegativeofthelock,andtheCOMconnecttothepositive.

• Jumpersetto1-2positionforPower-to-Unlocksafetytype(Normally open mode);set

to2-3positionforPower-off-to-Unlocktype(Normally closed mode).Notethatthe

unlockrelaymodeissetontheParametertabofDTCONFIGsoftware.

• Ifdifferentunlockingtimeisneededtobeconfigured,theDTCONFIGsoftwarecanbe

usedtochangetheUnlock TimingontheParametertab(seetheprogramsection).

JP_LK

12V 300mA

Jumper set to 1-2 position

+

-

+12V

LK - (GND)

LK+(COM)

N.O.

EB+

EB -

1

2

3

set to Normally open on the

Unlock Relay mode on DT-config

software.

A. Connection for Power-to-Unlock type:

12V 300mA

Jumper set to 2-3 position

+12V

LK - (GND)

LK+(COM)

N.O.

EB+

EB -

+

-

set to Normally Closed on the

Unlock Relay mode on DT-config

software.

JP_LK

1

2

3

B. Connection for Power--off-to-Unlock type:

+

-

+12V

LK - (GND)

LK+(COM)

N.O.

EB+

EB -

Remove the Jumper

set to Normally Open on the

Unlock Relay mode on DT-config

software.(default)

JP_LK

1

2

3

Note: Cut off this line when

using external power supply

+12V

LK - (GND)

LK+(COM)

N.O.

EB+

EB -

Remove the Jumper

set to Normally Closed on the

Unlock Relay mode on DT-config

software.

+

-

JP_LK

1

2

3

Note: Cut off this line when

using external power supply

2. External Power Supply Mode

Whentheelectroniclockisover12Vdc,additionalpowersupplyforthelockisneeded.

• Thepowersupplyforthelockmustbelessthan48Vdc1.5A.

• TheJumpermustberemovedwhenusingexternalpowersupply.Thedefaultsettingis

Power-to-Unlocktype(Normally open mode),ifusePower-off-to-Unlocktype,change

theUnlockRelaymodetoNormally closed mode.Notethattheunlockrelaymodeis

setontheParametertabofDTCONFIGsoftware.

• If differentunlockingtimeisneededtobeconfigured,pleaseusetheDTCONFIG

softwaretochangethesettingontheParametertab(seetheprogramsection).

C. Connection for Power-to-Unlock type:

D. Connection for Power--off-to-Unlock type:

5. Door Station Congurations

1. About room code(address):

RoomCode(alsocalledroomaddress)isacodeassignedtoeachmonitor,toidentifydifferent

monitors;eachmonitorhaveauniqueroomcodeinonebuidling.TheroomCodeisstoredin

eachMonitor’sinnerEEPROMmemory,anddoesnotloseeventhemonitorispoweroff.

2. About Debug State:

TheDebugStateisyourstartingpointforusingalltheapplicationsonDMR18.

WhenDoorStationisin

standby,press'#'key

Press"2#"keytoexitoutthedebugstate.

input'9008',theninputthe

AdminCode.(66666666by

default)

DebugStatemenuislaunched

[ 9 0 0 8 ]

Please Input Password

1 2 3

654

7 8 9

#0

*

RF CARD

> > D e b u g S t a t e < <

1 - # To o l s

0 - # R e d i a l

2 - # E x i t s

3. About Debug Tools:

DuringworkingatDebugState,press"1#"toentertoolspage,DebugToolsoverviewsis

shownasbelow:

1 . I n s t a l l e r S e t u p

2 . S e t u p

3 . C a r d M e m o r y

4 . O n l i n e M o n i t o r s

5 . O n l i n e D e v i c e s

6 . V o l t a g e M e a s u r e

Pres NO.

to select

*Back

Tools

> > D e b u g S t a t e < <

0 - # R e d i a l

2 - # E x i t s

1 - # To o l s

Item Submenu

1. Installer Setup

1.IDCode[1]

2.UnlockTiming[05]

3.UnlockOutput[0]

4.CardMemory[0]

5.DoorplateMode

6.AudioOptions...

7.Parameters...

8.InstallerCode...

9.Default...

2. Setup

1.Language[1]

2.ToneSelect[03]

3.ToneVolume[08]

4.UnlockCode[1111]

5.DisplayMode

6.Clock...

7.SetupCode...

8.About...

9.Default...

3. Card Manage

1.AddCard...

2.DeleteByCard

3.DeleteByM.code

4.CardsInformation

5.Format

4. Online Monitors

Tosearchtheonlinemonitors,inputthemonitorcode

numbertosearch

5. Online Devices

Tosearchtheonlinedoorstations.Max.4doorstation

canbesearched

6. Voltage Measure

Tocheckthe voltageof the monitor,note that the

monitormustbeonline.

Table1:

Basic Tools Detail:

Item Description

Factory

set

IDCode

Ifonlyonedoorstationisinstalledinthisbuilding,set

to1;

Ifmultidoorstationsareinstalled,primarydoorstation

mustbesetto1,andotherslavedoorstationsmust

besetfrom2to4.Notethatmax.4doorstationsis

availableinonebuilding

[1]

Single

UnlockTiming

Tosetthetimethathowlongthedoorkeepsopen

whendoorisreleased.Rangefrom01to99seconds.

[05]

5seconds

UnlockOutput

Tosettheunlockmodetomatchthecorresponding

lock.Randfrom0to1

0

CardManage

Tosetthecardlocation.Ifsetto0,thecardissavedin

doorstation.Ifsetto1,thecardissavedinDT-IPC

0

DoorplateMode

Tosetthecallingmode.Ifsetto0,it'stheauto

mode,thatmeansthecallingwillbeactivateddirectly

afterinputting2digitscode.Ifsetto1,it'sthemanual

mode,thatmeansyoushouldpress"#"buttonto

activatethecallingafterinputtingthecode.

[0]

Automode

AudioOptions...

Tosetthetalkingmode.Ifsetto0,handsfreemodeis

activated.Ifsetto1,handsetmodeisactivated.

0

Parameters... Toshowtheparameters,pleaserefertotable2.1

InstallerCode... Tochangedoorstationadministratorcode [66666666]

Default...

Notethisoperationisirreversible.Oncerestoreis

activated,allparameterswillreturntofactorydefault

settingexcepttheinformationofaccesscard.

Table2(InstallerSetup):

Item Description

Factory

set

MonitorTiming Toshowthemonitortime,Rangefrom6sto600s 30s

SwitchTiming

ToshowthesurveillancetimeforeachDoorStationor

CCTVcamera.Rangefrom6sto600s

40s

WaitTiming Toshowthecallingwaittime,Rangfrom10sto600s 30s

TalkTiming

Toshowthelimitationtimeoftalking,Rangefrom10s

to600s

90s

Monitor&Speack

ToenableIndoorMonitorundermonitoringstatecan

speaktoDoorStationatsametime.Ifsetto1,talk

enabled;setto0,disabled.

Monitor&Unlock

ToenableMonitorsundermonitoringstatecanopen

thedooratthesametime.Ifsetto0,unlockfunction

isdisabled;Setto1,unlockisenable;Setto2,unlock

isenableandcloseatonce;Setto3,unlockisenable

andclosein5s.

[1]

RingNumbers

Toshowringtimeswhendoorstationcallsmonitor.4

optionsforchoice.Ifsetto0,ringonce.Ifsetto1,ring

twice.Ifsetto2,ringthreetimes.Ifsetto3,cyclering

[1]

NameListDisplay

Mode

Toshowthenamelistdisplaymode.Ifsetto0,it'sthe

DT-Configdisplaymode.Ifsetto1,it'stheSimulate

displaymode

[0]

WorkingMode

Toshowtheworkingmode.Ifsetto0,it'stheapartment

systemmode.Ifsetto1,it'sthevillamode.

[0]

Table2.1(Parameters):

Note:

thissectionissetonDT-Congsoftware,formoredetailinformations,pleaserefertothe

DT-Congsoftwareuserinstructions.

Item Description

Factory

set

Language

Tochangelanguage.thecodeformatis4digits.Pleaserefer

topart5,section10(changedoorstationlanguage)formore

detailinformations.

01

ToneSelect

SelectthechimeofDoorStationincallingwaitstate,12

chordtunesareavailable,keyin01to12toselect.

03

ToneVolume

Adjustthetonevolumefordooorstationincalling.Rangfrom

01~15

08

UnlockCode

TochangeunlockcodeinCommonCodeUnlockmode,in

4-digitsformat.1111isthedefaultunlockcode.

[1111]

DisplayMode

ToselecttheDoorStationscreenmenu.Ifsetto0,the

screendisplaysthevisitor'simagewhentalking.Ifsetto1,the

screendisplaysiconswhentalking.

[0]

Clock...

Tosetdateandtime.

Dateformat:ifsetto0,dateformatisDD/MM/YY,ifsetto

1,dateformatisMM/DD/YY.

Timeformat:ifsetto0,timeformatis24hourstandard.Ifset

to1,timeformatis12hourstandard.

SetupCode TochangetheProgramCode. [88888888]

About...

1.Hardwareversion---ToshowtheDoorStation(including

ACS)hardwareinformation

2.Softwareversion---ToshowtheDoorStation(including

ACS)softwareinformation

3.ManufactureDate---Toshowthemanufacturingdate

4.DialingCounts---Toshowthecalloperationcounts

5.CallsCounts---Toshowtheestablishedcallingcounts

6.UnlockCounts---Toshowtheunlockoperationcounts

7.StandbyVoltage---Toshowthevoltagethatthedoor

stationinstandby.

8.WorkingVoltage---Toshowthevoltagethatthedoor

stationinworking.

9.VideoStandard---PALorNTSCstandard

10.UI_CODE---ToshowtheUIbytecountsandcheckbox

11.MCM-VER---ToshowtheversionandlanguageforMCM

12.Updated---ToshowtheupdatedtimeforUI

Default...

RestoreallSetupparameterstofactorydefaultsetting,Please

notethatthisoperationisanirreversible

Table3(Setup):

Item Description

Factory

set

AddCard... Toaddtheusercard

DeleteByCard Todeletecardbyusercard

DeleteByM.code Todeletecardbyroomcode

CardsInformation Toshowtheinformationsaboutcards

Format Toformatinformationsaboutcards

Table4(CardMemory):

4. Calling and Unlock Operation:

TheDMR18doorstationisadigitalstationwith320*240pixelsLCDscreen,colorCCD

camera,nightviewLED,anddigitalkeypad.

VisitorscancalltheapartmentbydialingtheFlatCode(apartmentnumber)onthekeypad.

Iftheydon’tknowtheFlatCode(apartmentnumber),theycansearchthenamelistonthe

screen.Ifthedoorstationisinstandby,visitorsneedtopress'9#'todisplaytheusernamelist.

Press"#"keytoscrollnext/lastpage.andusekey1to8keyoneachpagetocallthedesired

at.

ResidentscanopenthedoorbyusingtheiruniqueUnlockCode(four-digitPINcode).Ifthe

doorstationisinstandbymode,press'#'key,theninputthefour-digitunlocktoopenthedoor.

Pleaserefertopart5,section7(Howtousecodeunlockfunction)formoredetailinformation.

5. About Default Set:

TheDefaultSetisveryimportant.Whenthedoorstationmissupthesettingsinanyway,

themostquicklyandeasywaytosolvetheproblemistoactivatethedefaultsettingondoor

station.Thedefaultsettingsalreadyhavealltherightsettingsforone-buildingsystem,that

meansthesystemwillworknormallywithoutanyadditionalsettings..

Note:

Ifthedoorstationworksasapartmentsystemmode,input01~32tocalltherelevant

monitor.Ifthedoorstationworksasvillamode,input01tocallthemonitorswhichitscodeis

from00~15.Input02tocallthemonitorswhichitscodeisfrom16~31.pleaserefertotable

2.1(workingmode)

InDebugState,press'1#'

key

InToolsmenu,press'1'

key

InputInstallercode(66666666

bydefault),thenpress"#"tosave

Press'9'key,a

passwordwillbeasked.

> > D e b u g S t a t e < <

0 - # R e d i a l

2 - # E x i t s

1 . I D C o d e . [ 1 ]

2 . U n l o c k T i m i n g [ 0 5 ]

3 . U n l o c k O u t p u t [ 0 ]

4 . C a r d M e m o r y [ 0 ]

5 . D o o r p l a t e M o d e

6 . A u d i o O p t i o n s . . .

7 . P a r a m e t e r s . . .

8 . I n s t a l l e r C o d e . . .

Press No.

to select

*Back

Installer

Setup

9 . D e f a u l t

1 - # To o l s

1 . I n s t a l l e r S e t u p

2 . S e t u p

3 . C a r d M e m o r y

4 . O n l i n e M o n i t o r s

5 . O n l i n e D e v i c e s

6 . V o l t a g e M e a s u r e

Pres NO.

to select

*Back

Tools

*Back

[ - - - - - - - - ]

Please Input Password

# Save

9 . D e f a u l t . . .

Press“#”,Input“8002”,then

inputSetupCodeorAdmin

Code(88888888or66666666by

default)

Press“2”toentertone

selectitem.

6. Change Ring Tone:

Thereare12differentringtones,IfdoorstationrunsasDebugState,youcanpress[1#]-->

[2]Setup-->[2]ToneSelecttoentertonesettingpage.IfitrunsasNormalState,followthese

steps:

Input2digitsnumber,

thenpress“#”tosave

thesetting

[ 8002 ]

Please Input Password

1 2 3

654

7 8 9

#0

*

RF CARD

1 . L a n g u a g e [ 1 ]

3 . To n e V o l u m e [ 0 3 ]

4 . U n l o c k C o d e [ 1 1 1 1 ]

5 . D i s p l a y M o d e

6 . C l o c k

7 . S e t u p C o d e

8 . A b o u t

9 . D e f a u l t

Press No.

to select

*Back

Setup

*Back

[ - - ]

( 01~12)

# Save

2 . To n e S e l e c t [ 0 3 ]

7. Change Installer Code(administrator password):

TheInstallerCodeisthepasswordtoaccessthedoorstationdebugState.Thedefault

InstallerCodeis'66666666'.NotethatiftheDefaultSethavebeenactivated,theInstallerCode

willbesettodefaultvalue.

8. How to use code unlock function:

Pleaserefertothefollowingoperations:

> > D e b u g S t a t e < <

0 - # R e d i a l

2 - # E x i t s

1 . I D C o d e [ 1 ]

2 . U n l o c k T i m i n g [ 0 5 ]

3 . U n l o c k O u t p u t [ 0 ]

4 . C a r d M e m o r y [ 0 ]

5 . D o o r p l a t e M o d e

6 . A u d i o O p t i o n s . . .

7 . P a r a m e t e r s . . .

9 . D e f a u l t

Press1~9

to select

*Back

Installer

Setup

1 - # To o l s

8 . I n s t a l l e r C o d e . . .

1 . I n s t a l l e r S e t u p

2 . S e t u p

3 . C a r d M e m o r y

4 . O n l i n e M o n i t o r s

5 . O n l i n e D e v i c e s

6 . V o l t a g e M e a s u r e

Pres NO.

to select

*Back

Tools

*Back

[ - - - - - - - - ]

( * * * * * * * *)

# Save

8 . I n s t a l l e r C o d e . . .

InDebugState,press'1#'

key

InputanewInstallerCodeand

thenpress'#'keytoconrm

press'1' press'8'

[ - - - - ]

Please Input Password

1 2 3

654

7 8 9

#0

*

RF CARD

1 2 3

654

7 8 9

#0

*

RF CARD

[8017 ]

i

Door Open

WhentheDoorStationisin

standby,Press“#”

Ifveriedcorrectly,

dooropen

Input4digitsUnlockCode

directly

Press“#”,Input“8002”,

theninputSetupCodeor

AdminCode(88888888or

66666666bydefault)

Press“4”toenterunlock

codeitem.

9. Change Unlcok Code:

IfdoorstationrunsasDebugState,youcanpress“1#”toactivateToolsMenu,thenselect“2”

toentersetuppage,thenselect4item.IfitrunsasNormalState,followthesesteps:

[ 8002 ]

Please Input Password

1 2 3

654

7 8 9

#0

*

RF CARD

1 . L a n g u a g e [ 1 ]

2 . To n e S e l e c t [ 0 3 ]

3 . To n e V o l u m e [ 0 3 ]

5 . D i s p l a y M o d e

6 . C l o c k

7 . S e t u p C o d e

8 . A b o u t

9 . D e f a u l t

Press No.

to select

*Back

Setup

*Back

[ - - - - ]

( * * * *)

# Save

4 . U n l o c k C o d e [ 1 1 1 1 ]

Input4digitsnumber,

thenpress“#”toupdate

10. User Card Management:

ThissectionexplainshowtocongurethekeyfobfunctiononDMR18,Thekeyfobisusedto

openthelock.Total1000keyfobscanberegisteredwithonedoorstation.Whenswipingthe

fobtothedoorstation,thedistancemustbelessthan3centimeter.

KeyFobsmustberegisteredontheDoorstationthatcanbeusedtoopenthedoor.

Register the Key Fobs:

AlltheregisteredkeyfobsarecalledUserCards/UserKeyFobs.Newfobs/cardsneedto

beregisteredonebyonetotheDoorstationtobecomeavalidUserCard/UserKeyFob;and

everyUserCard/UserKeyFobisrelatedtoacertainMonitorAddress(Flatcode).

WhentheDoorstationisstandby,press[#]-->[9008]-->Password([66666666bydefault])

togetintotheDebugModeMenu,thenPress[1#]-->[3]CardManage-->[1]AddCardtoget

intotheAddCardpage.Pleaseseethefollowings.

EnterAddCardmenu,and

RoomCodeisasked.

InputRoomCode Readthecardtobe

authorized

Delete user cards:

Delete By Card:

InDebugState,Press[1#]-->

[3]CardManage-->[2]Delete

ByCardtoenterDeletebyCard

page.as shown on the right,

thenshowthecardsyouwantto

deleteonebyone.

2 . D e l e t e B y C a r d . . .

* Back # Save

Show The Card

2 . D e l e t e B y C a r d . . .

* Back # Save

U

s

e

r

C

a

r

d

C a r d numbs:

1 5 9 7 7 1 3 1

Show The Card

RegisteredUserCards/KeyFobscanbedeletedfromtheDoorstation,oncedoingthedelete

operation,thecard/keyfobscannotopenthedooranymore.Theycanalsobere-registered

againtobecomeavalidUserCard/UserKeyFob.TherearetwowaystodeleteUserCards/

UserKeyFobs:

1.Deletebycard:showtheunwantedcard(s)whentheDoorstationisinDeleteCardMode

2.Deletebyroomnumber:deletealltheregisteredUserCardsrelatedtothatroomnumber.

1 . A d d C a r d . . .

* Back # Save

Please Input Room Code

[ - - ]

1 . A d d C a r d . . .

* Back # Save

Show the card

[ 0 1 ]

1 . A d d C a r d . . .

* Back # Save

[ 0 1 ]

C a r d numbs :

1 5 9 7 7 1 3 1

Show The Card

U

s

e

r

C

a

r

d

3 . D e l e t e B y M . c o d e

* Back # Save

Please Input Room Code

[ - - ]

3 . D e l e t e B y M . c o d e

* Back # Save

U pd a t e d

[ 0 1 ]

InDebugState,Press[1#]-->

[3]CardManage-->[3]Delete

ByM.Code toenter Deleteby

M.Code page.as shown on

theright,thenInputtheRoom

Code,press“#”toconfirm; all

associatedcardswillbedeleted.

Delete by Room Number:

Card information:

Format:

EnterCardInformationpage,andthe

screenwilldisplaytheauthorizedUser

Cards count, and card read access

eventscount.

EnterCardFormatpage,apassword

will be asked,input 8digits installer

password(66666666bydefault),then

press"#"keytosave,formatoperation

isactivated.allcardinformationwillbe

cleared.

4 . C a r d s I n f o r m a t i o n

* Back # Save

Card Count: 1000

5 . F o r m a t

* Back # Save

Please Input Password

[ - - - - - - - - ]

11. Change Door Station Language:

It'sconvenienttochangetheuserinterfaceforDMR18.JustputtheconglestotheSDcard

andbymeansofthedigitalkeypadofdoorstation,only30secondsisneededtoupdate.

L1

T/R -

CN-LK

T/R+

J/KMB JP-LK

Bus

Insert SD card

SD Card Slot

EB+

EB-

N.O

LK+

LK-

+12V

L2

12

3

12

3

Step 1: Insert the SD card which is

containedconglesintotheSDcardslot

whereisatthebackofthedoorstation.

Refertotherightdiagram.

Step2:

IfdoorstationrunsasDebugState,youcanpress“1#”toactivateToolsMenu,select“2”to

entersetuppage,thenselect1item.IfitrunsasNormalState,followthesesteps:

Language code number:

[8017 ]

i

Download

[ 8002 ]

Please Input Password

1 2 3

654

7 8 9

#0

*

RF CARD

2 . To n e S e l e c t [ 0 3 ]

3 . To n e V o l u m e [ 0 3 ]

5 . D i s p l a y M o d e

6 . C l o c k

7 . S e t u p C o d e

8 . A b o u t

9 . D e f a u l t

Press No.

to select

*Back

Setup

*Back

[ - - - - ]

( Code Number)

# Save

1 . L a n g u a g e

4 . U n l o c k C o d e [ 1 1 1 1 ]

1 . L a n g u a g e [ 1 ]

Press“#”,Input“8002”,then

inputSetupCodeorAdmin

Code

Press1

Input4digitscodenumber,

Refertothetable.

Whenthedoorstationoutput

alongsoundDI...,thatmeans

UIupdatingisnished.

8101: English

8102: French

8103: Spanish

8104: Italian

8105: German

8106: Dutch

8107: Portuguese

8108: S-Chinese

8109: T-Chinese

8110: Greek

8111: Turkish

8112: Polish

8113: Russian

8114: Slovakia

8115: Hungray

8116: Czech

12. Search online door stations and monitors:

“OnlineSearch”isaveryusefulfunctionthatcanhelptheinstallertoeasilycheckthe

connectivityofalltheMonitors.Pleasenote,Onlinedoesnotmeanviatheinternet.Please

refertothefollowings:

> > D e b u g S t a t e < <

0 - # R e d i a l

2 - # E x i t s

* Back # Save

[DS1 ] : Online

[DS2 ] : Fail

[DS3 ] : Fail

[DS4 ] : Fail

5 . O n l i n e D e v i c e s

1 - # To o l s

1 . I n s t a l l e r S e t u p

2 . S e t u p

3 . C a r d M e m o r y

4 . O n l i n e M o n i t o r s

5 . O n l i n e D e v i c e s

6 . V o l t a g e M e a s u r e

Pres NO.

to select

*Back

Tools

InDebugState,press'1#'

key

Press'5'key Checkdoorstations

connectionstatus

Check online door stations:

> > D e b u g S t a t e < <

0 - # R e d i a l

2 - # E x i t s

* Back # Save

(Search Range)

[ - - ] ~ [ - - ]

4 . O n l i n e M o n i t o r s

* Back # Save

[ 01 ] Online

[ 02 ] Online

[ 03 ] Online

[ 04 ] Fall

[ 05 ] Online

4 # . O n l i n e M o n i t o r s

1 - # To o l s

1 . I n s t a l l e r S e t u p

2 . S e t u p

3 . C a r d M e m o r y

4 . O n l i n e M o n i t o r s

5 . O n l i n e D e v i c e s

6 . V o l t a g e M e a s u r e

Pres NO.

to select

*Back

Tools

InDebugState,press'1#'

key

Press'4'key Input2digits

monitorcode

SearchRange:inputthemonitoradress.Forexample,

inputtherangefrom01to05.Youwillseetheconnection

statusoftheselectedmoinitors.

13. Namelist function:

DMR18isdesignedtohavedigitalkeypadandbigTFTscreen.Itsnamelistwasshownon

thescreenandcustomercandothecallingoperationthroughthedigitalkeypadguidedby

Namelistonthescreen.2typesofnamelistcanbeshownonthescreen:DT-Congnamelist

andSimulatenamelist.

Enter namelist page:

Check online monitors:

Send namelist to monitors

Press'9#'instandbymodetodisplaytheusernamelist.Press"#"keytoscrollnext/lastpage.

andusekey1to8keyoneachpagetocalltheatyouwant.PleaserefertotheDT-Cong

softwreuserinstructionsforcongurethenamelist.

Thenamelistcanbesenttomonitorsbydoorstationdirectly.Connectthedoorstationand

montiorscorrectlytothesystem.Thenpress#8012instandbymode,andinputpassword

(66666666bydefault)tosendnamelisttoallthemonitors.

6. Specication

● Power supply: DC24V(Powered by DT-DPS)

● Camera Lens : 1/4 ACS 4T image sensor with DSP processor

● Power consumption: Standby 3W;Working status 9W

● Screen: 3.5 inch TFT

● Resolution: 320(R, G, B)X240 pixels

● Video signal: CCIR/EIA Optional

● Wiring: 2 wires, non-polarit

DT-ENG-DMR18-V1 2011S0621

Page is loading ...

Schick Handel DMR18 User manual

Schick Handel DMR18 User manual

in other languages

Other documents