MSI WT75 (Intel 8th Gen) Owner's manual

i

MS-9B05

WindBOX

Industrial Data Machine

ii

Preface MS-9B05

Copyright and Trademarks Notice

a registered trademark of Micro-Star Int’l Co., Ltd. All other marks and names

mentioned may be trademarks of their respective owners. No warranty as to

accuracy or completeness is expressed or implied. MSI reserves the right to

make changes to this document without prior notice.

Revision History

Revision Date

V1.3 2020/12

Technical Support

If a problem arises with your product and no solution can be obtained from

the user’s manual, please contact your place of purchase or local distributor.

Alternatively, please visit https://www.msi.com/support/ for further guidance.

iii

Preface MS-9B05

Safety Instructions

￭ Always read the safety instructions carefully.

￭ Keep this User’s Manual for future reference.

￭ Keep this equipment away from humidity.

￭ Lay this equipment on a reliable at surface before setting it up.

￭ The openings on the enclosure are for air convection hence protects the

equipment from overheating. DO NOT COVER THE OPENINGS.

￭ Make sure the voltage of the power source and adjust properly 110/220V

before connecting the equipment to the power inlet.

￭ Place the power cord such a way that people can not step on it. Do not place

anything over the power cord.

￭ Always Unplug the Power Cord before inserting any add-on card or module.

￭ All cautions and warnings on the equipment should be noted.

￭ Never pour any liquid into the opening that could damage or cause electrical

shock.

￭ If any of the following situations arises, get the equipment checked by ser-

vice personnel:

▶ The power cord or plug is damaged.

▶ Liquid has penetrated into the equipment.

▶ The equipment has been exposed to moisture.

▶ The equipment does not work well or you can not get it work according

to User’s Manual.

▶ The equipment has dropped and damaged.

▶ The equipment has obvious sign of breakage.

￭ DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT UNCONDI-

TIONED, STORAGE TEMPERATURE ABOVE 60

o

C, IT MAY DAMAGE THE

EQUIPMENT.

警告使用者:

此為甲類資訊技術設備，於居住環境中使用時，可能會造成射頻擾動，在此種情

況下，使用者會被要求採取某些適當的對策。

iv

Preface MS-9B05

Chemical Substances Information

In compliance with chemical substances regulations, such as the EU REACH

Regulation (Regulation EC No. 1907/2006 of the European Parliament and the

Council), MSI provides the information of chemical substances in products at:

https://www.msi.com/html/popup/csr/evmtprtt_pcm.html

Battery Information

European Union:

Batteries, battery packs, and accumulators should not be

disposed of as unsorted household waste. Please use the

public collection system to return, recycle, or treat them in

compliance with the local regulations.

廢電池請回收

Taiwan:

For better environmental protection, waste batteries should

be collected separately for recycling or special disposal.

California, USA:

The button cell battery may contain perchlorate material

and requires special handling when recycled or disposed

of in California.

For further information please visit:

https://www.dtsc.ca.gov/hazardouswaste/perchlorate/

Danger of explosion if battery is incorrectly replaced. Replace only with the

same or equivalent type recommended by the manufacturer.

v

Preface MS-9B05

CE Conformity

Hereby, Micro-Star International CO., LTD declares that this device

is in compliance with the essential safety requirements and other

relevant provisions set out in the European Directive.

FCC-A Radio Frequency

Interference Statement

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at his own expense.

Notice 1

The changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Notice 2

Shielded interface cables and AC power cord, if any, must be used in order to

comply with the emission limits.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received, including interference that

may cause undesired operation.

WEEE Statement

Under the European Union (“EU”) Directive on Waste Electrical and

Electronic Equipment, Directive 2012/19/EU, products of “electrical

and electronic equipment” cannot be discarded as municipal waste

anymore and manufacturers of covered electronic equipment will be

obligated to take back such products at the end of their useful life.

vi

Preface MS-9B05

CONTENTS

Copyright and Trademarks Notice ................................................................. ii

Revision History ............................................................................................ ii

Technical Support .......................................................................................... ii

Safety Instructions .........................................................................................iii

Chemical Substances Information ............................................................... iv

Battery Information ....................................................................................... iv

CE Conformity ............................................................................................... v

FCC-A Radio Frequency Interference Statement ......................................... v

WEEE Statement .......................................................................................... v

1 Overview.......................................................................................1-1

System Overview .......................................................................................1-2

System Specications ................................................................................1-7

Motherboard Jumpers ..............................................................................1-10

2 Getting Started .............................................................................2-1

System Internal View .................................................................................2-2

Memory ......................................................................................................2-3

M.2 Slot ......................................................................................................2-4

Mini-PCIe Slot ............................................................................................2-5

2.5” HDD/SSD ............................................................................................ 2-6

Wall Mount (Optional) ................................................................................2-8

DIN Rail Mount 1 (Optional) .......................................................................2-9

DIN Rail Mount 2 (Optional) .....................................................................2-10

VESA Mount ............................................................................................. 2-11

3 BIOS Setup ................................................................................... 3-1

Entering Setup ...........................................................................................3-2

The Menu Bar ............................................................................................3-4

Main ...........................................................................................................3-5

Advanced ...................................................................................................3-6

Boot .......................................................................................................... 3-12

Security ....................................................................................................3-13

Chipset .....................................................................................................3-22

Power .......................................................................................................3-23

Save & Exit ...............................................................................................3-25

Appendix GPIO WDT Programming ............................................... A-1

Abstract ..................................................................................................... A-2

General Purposed IO ................................................................................ A-3

Watchdog Timer ........................................................................................ A-4

1-1-1

Thank you for choosing the MS-9B05, an excellent industrial data ma-

chine from MSI.

The MS-9B05’s wide heatsink fanless solution eliminates the noise and

the risk of fan failure. Furthermore, it supports VESA wall-mount inter-

face for various scenarios like digital signage, kiosk, industrial control

and POS with aordable expenditure, which not only meets the demand

of Industrial applications but also fullls the needs of companies, govern-

ments and institutes for general applications.

1 Overview

1-2

Overview MS-9B05

System Overview

h System I/O & Controls

SKU1

SKU2

3

6

7

8

16

2

4 5

1

10

9

12

11

13

14

1 16

10

1 16

9

13

14

15

1-3

Overview MS-9B05

1

WiFi Antenna Connector (Optional)

This connector allows you to connect an external antenna for wireless

LAN.

2

GbE RJ45 Port

The standard RJ45 LAN jack is provided for connection to the Local

Area Network (LAN). You can connect a network cable to it.

3

Extend Switch Connector

This connector is provided for remote power button control.

4

USB 3.2 Gen 1 Port (For SKU1)

USB 3.2 Gen 1, the SuperSpeed USB, delivers up to 5Gbps high-

speed data transfer for various devices, such as storage devices,

hard drives, video cameras, etc.

USB 3.2 Gen 2 Port (For SKU2)

USB 3.2 Gen 2, the SuperSpeed USB 10Gbps, delivers high-speed

data transfer for various devices, such as storage devices, hard

drives, video cameras, etc.

1-4

Overview MS-9B05

5

RS232/422/485 Serial Port

The serial port is a 16550A high speed communications port that

sends/receives 16 bytes FIFOs. It supports barcode scanners, bar-

code printers, bill printers, credit card machine, etc.

5 1

9 6

RS232

PIN SIGNAL DESCRIPTION

1

2

3

4

5

6

7

8

9

DCD

RXD

TXD

DTR

GND

DSR

RTS

CTS

POWER

Data Carrier Detect

Receive Data

Transmit Data

Data Terminal Ready

Ground

Data Set Ready

Request To Send

Clear To Send

5V or 12V selected by GPIO (BIOS)

RS422

PIN SIGNAL DESCRIPTION

1

2

3

4

5

6

7

8

9

TXD-

TXD+

RXD+

RXD-

GND

NC

Transmit Data, Negative

Transmit Data, Positive

Receive Data, Positive

Receive Data, Negative

Ground

No Connection

RS485

PIN SIGNAL DESCRIPTION

1

2

3

4

5

6

7

8

9

D-

D+

NC

GND

NC

Data, Negative

Data, Positive

No Connection

Ground

No Connection

1-5

Overview MS-9B05

6

Mic-In Jack

Used as a connector for a microphone.

Line-In Jack (by AP driver)

Used for connecting external audio output devices.

7

S/PDIF-Out Jack

S/PDIF (Sony/Philips Digital Interface Format) is a type of digital au-

dio interconnect used in consumer audio equipment, home theaters

and other digital high-delity systems.

Line-Out Jack

This connector is provided for headphones or speakers.

8

DC Power Jack

Power supplied through this jack supplies power to the system.

9

Power Button

Press the button to turn the system on or o.

10

Hard Disk Drive LED

This indicator shows the activity status of the HDD. It ashes when

the system is accessing data on the HDD and remains o when no

disk activity is detected.

11

DVI-D Port (For SKU1)

The DVI-D (Digital Visual Interface-Digital) connector allows you to

connect a monitor. It provides a high-speed digital interconnection

between the computer and its display device.

12

DisplayPort (For SKU1)

DisplayPort is a digital display interface standard. This connector is

used to connect a monitor with DisplayPort inputs.

13

HDMI 1.4 Port

The High-Denition Multimedia Interface (HDMI) is an all-digital audio/

video interface capable of transmitting uncompressed streams. HDMI

supports all TV format, including standard, enhanced, or high-deni-

tion video, plus multi-channel digital audio on a single cable.

14

USB 2.0 Port

The USB (Universal Serial Bus) port is for attaching USB devices

such as keyboard, mouse, or other USB-compatible devices. It sup-

ports up to 480Mbit/s (Hi-Speed) data transfer rate.

1-6

Overview MS-9B05

15

HDMI 2.0 Port (For SKU2)

The High-Denition Multimedia Interface (HDMI) is an all-digital audio/

video interface capable of transmitting uncompressed streams. HDMI

supports all TV format, including standard, enhanced, or high-deni-

tion video, plus multi-channel digital audio on a single cable.

16

LTE Antenna Connector (Optional)

This connector allows you to connect an external antenna for LTE.

1-7

Overview MS-9B05

System Specications

Processor

■ SKU1: 8th Gen Intel

®

Mobile Whiskey Lake-U Celeron

®

Processor, DC, 15W

■ SKU2: 8th Gen Intel

®

Mobile Whiskey Lake-U Core™ i5 Processor, QC,

15W

Memory

■ 2 x 260-pin SO-DIMM slots

■ Support the maximum of 32GB

■ SKU1: Dual-channel for DDR4 2133 MHz

■ SKU2: Dual-channel for DDR4 2400 MHz

Network

■ 1 x Intel

®

I219LM GbE LAN PHY

■ 1 x Intel

®

I210-AT GbE LAN

Storage

■ 1 x SATA 6 Gb/s, 2.5” HDD/SSD

■ 1 x mSATA slot (shared with Mini PCIe)

Expansion Slot

■ 1 x Half/Full-size Mini PCIe slot (w/ mSATA)

■ 1 x Half/Full-size Mini PCIe slot (w/ Nano-SIM holder)

■ SKU1

» 1 x M.2 E Key 2230 slot (2 x PCIe x1, USB 2.0)

» 1 x M.2 M Key 2242 slot (PCIe x4)

■ SKU2

» 1 x M.2 E Key 2230 slot (2 x PCIe x1, USB 2.0)

» 1 x M.2 M Key 2242 slot (PCIe x4, SATA)

Important

• MS-9B05 only supports installing ONE WiFi / BT module. Please install

your WiFi / BT module to Mini PCIe slot1, Mini PCIe slot2 or M.2 E Key slot.

Audio

■ Realtek

®

ALC887-VD2-CG HDA Codec

■ Compliant with Azalia 1.0 specs

1-8

Overview MS-9B05

Graphics

■ Intel

®

UHD Graphics 620

■ Shared system memory up to 1.7 GB SDRAM

■ 3 independent displays

■ SKU1

» HDMI 1.4 up to 4096 x 2160 @24Hz

» DisplayPort 1.2 up to to 4096 x 2304 @60Hz

» DVI-D up to 1920 x 1200 @60Hz

■ SKU2

» HDMI 2.0 up to 4096 x 2160 @60Hz

» HDMI 1.4 up to 4096 x 2160 @24Hz

Important

• MS-9B05 supports Collage Display Mode with two independent displays.

SKU1 DP 1.2 HDMI 1.4

SKU2 HDMI 2.0 HDMI 1.4

Check https://www.intel.com/content/www/us/en/support/articles/000006547/

graphics-drivers.html for details.

• SKU2’s HDMI 2.0 port does not support audio and hot plug. To ensure

proper operation of the HDMI 2.0 display, follow the instructions:

1. Connect the HDMI cable from the display to the HDMI 2.0 port on the

system left panel. Connect the display power cord.

2. Disconnect the system power cord to ensure a complete system

shutdown.

3. Reconnect the system power cord and power on the system.

4. Power on the display. The display should be able to work properly.

Left Panel Input/Output

■ 2 x WiFi Antenna Connectors (Optional)

■ 1 x Power Button

■ 1 x Hard Disk Drive LED

■ 1 x DVI-D Port (For SKU1)

■ 1 x DisplayPort (For SKU1)

■ 1 x HDMI 1.4 Port

■ 2 x HDMI 2.0 Ports (For SKU2)

■ 4 x USB 2.0 Ports

1-9

Overview MS-9B05

Right Panel Input/Output

■ 2 x WiFi Antenna Connectors (Optional)

■ 2 x GbE RJ45 Ports

■ 1 x Extend Switch Connector

■ 2 x USB 3.2 Gen 1 Ports (For SKU1)

■ 2 x USB 3.2 Gen 2 Ports (For SKU2)

■ 2 x RS232/422/485 Serial Ports

■ 1 x Mic-In Jack/ Line-In Jack (Line-In by AP driver)

■ 1 x S/PDIF-Out Jack/ Line-Out Jack

■ 1 x DC Power Jack

Power Supply

■ DC-in 9~36V with Lockable DC Jack

Dimension & Weight

■ 260 x 185 x 27mm

■ 1.77 kg

OS Support

■ Windows 10 IoT Enterprise LTSC/SAC 1809 (64-bit, RS5)

■ Linux Ubuntu/ Linux Fedora (by request)

Regulatory Compliance

■ EMC: FCC, CE, RCM, VCCI, BSMI

■ Safety: BSMI, CE

Environment

■ Operating Temperature:

» -10 ~ 50

o

C (SSD)

» -10 ~ 40

o

C (HDD)

■ Storage Temperature: -20 ~ 80

o

C

■ Humidity: 10 ~ 90% RH, non-condensing

1-10

Overview MS-9B05

Motherboard Jumpers

JATX1

JCMOS1 JME_DIS1

Jumper Name Default Setting Description

JCMOS1

1

1-2: Normal 2-3: Clear CMOS

JATX1

1

1-2: ATX 2-3: AT

JME_DIS1

1

1-2: Normal 2-3: ME Disable

1-2-1

This chapter provides you with the information on hardware setup

procedures. While doing the installation, be careful in holding

the components and follow the installation procedures. For some

components, if you install in the wrong orientation, the components will

not work properly.

Use a grounded wrist strap before handling computer components. Static

electricity may damage the components.

Important

Always unplug the power cord before installing any components.

2 Getting Started

2-2

Getting Started MS-9B05

System Internal View

2-3

Getting Started MS-9B05

Memory

1. Locate the SO-DIMM slot.

2. Align the notch on the DIMM with

the key on the slot and insert the

DIMM into the slot at a 45-degree

angle.

3. Push the DIMM gently downwards

until the slot levers click and lock

the DIMM in place.

Important

• You can barely see the golden nger if the DIMM is properly inserted in the

DIMM slot.

• To uninstall the DIMM, ip the slot levers outwards and the DIMM will be

released instantly.

2-4

Getting Started MS-9B05

M.2 Slot

1. Locate the M.2 slot. Remove the

M.2 card screw preinstalled on the

motherboard.

2. Insert the card into the slot at a

45-degree angle.

3. Push the card gently downwards

and fasten it with a screw.

Page is loading ...

MSI WT75 (Intel 8th Gen) Owner's manual

MSI WT75 (Intel 8th Gen) Owner's manual

Related papers

Other documents