Armstrong Flooring 52513031 Installation guide

Brand: Armstrong Flooring

Model: 52513031

Type: Installation guide

Vinyl Composition Tile

Installation System

Product Gauge Size

Adhesive/

Full Spread

Adhesive/

Tile-On

Vinyl No-Wax

(Dry Back)

0.045"

(1.1 mm)

Feature Strips:

1" (2.5 cm),

2" (5.0 cm) or

6" x 24"

(15.2 cm x 61 cm)

all others 12" x 12"

(30.5 cm x 30.5 cm)

S-515, S-525,

S-700, or S-750

S-515, S-525, or

S-750

Urethane No-Wax

(Dry Back)

0.080"

(2.0 mm)

IMPERIAL TEXTURE 0.094"

(2.4 mm)

STONETEX

ChromaSpin

COMPANION SQUARE

Feature Tile/Strips

IMPERIAL TEXTURE

RAVE

MULTICOLOR

0.125"

(3.2 mm)

ARTEFFECTS 0.125"

(3.2 mm)

RAFFIA 0.125"

(3.2 mm)

12" x 24"

(30.5 cm x 61 cm)

SAFETY ZONE

0.125"

(3.2 mm)

12" x 12"

(30.5 cm x 30.5 cm)

S-515, S-525,

S-700, S-750, or

S-240

Installation:

Location: All grade levels

Suitable Substrates:

All substrates listed below must be properly prepared and meet the

requirements discussed in Chapter III, Subﬂoors and Underlayments. There

may be certain exceptions and special conditions for these substrates to be

suitable for the Vinyl Composition Tile Installation System.

Full Spread:

• Concrete • Ceramic Tile, Terrazzo, Marble

• Approved Suspended Wood • Polymeric Poured

(seamless) Floors

• Steel, Stainless Steel, Aluminum,

Lead, Copper, Brass, Bronze

Tile-On:

• Existing Resilient Sheet Floors

• Vinyl Composition, Vinyl Asbestos, Asphalt, Rubber and Vinyl Tile-on

Grade or Suspended Only

Job Conditions/Preparation:

• Resilient ﬂooring should only be installed in temperature-controlled

environments. It is necessary to maintain a constant temperature before,

during, and after the installation. Therefore, the permanent or temporary

HVAC system must be in operation before the installation of resilient

ﬂooring. Portable heaters are not recommended as they may not heat the

room and subﬂoor sufﬁciently. Kerosene heaters should never be used.

• Substrates must be dry, clean, smooth, and free from paint, varnish, wax,

oils, solvents and other foreign matter. In renovation or remodel work,

remove any existing adhesive residue* so that no ridges or puddles are

evident and a thin, smooth ﬁlm remains.

• When using S-240 Epoxy Adhesive, remove any existing adhesive residue*

so that 80% of the overall area of the original substrate is exposed. If these

requirements are not followed, curled and/or loose tile could result. For Tile-

On, remove wax or other ﬁnishes with a commercially available liquid wax

stripper. Replace or repair indented or otherwise damaged areas.

• Allow all ﬂooring materials and adhesives to condition to the room

temperature for a minimum of 48 hours before starting the installation.

• The area to receive the resilient ﬂooring should be maintained at a minimum

of 65°F (18°C) and a maximum of 100°F (38°C) for 48 hours before, during,

and for 48 hours after completion. When using S-240 Epoxy Adhesive, the

maximum room temperature should not exceed 85°F (29°C).

• During the service life of the ﬂoor, the temperature should never rise above

100°F (38°C) nor fall below 55°F (13°C). The performance of the ﬂooring

material and adhesives can be adversely affected outside this temperature

range.

• For concrete substrates, conduct moisture testing (moisture vapor emission

rate [MVER]) and/or percent relative humidity (in-situ probe). Bond tests

must also be conducted for compatibility with the substrate. Please refer to

Chapter III, Subﬂoors and Underlayments.

• Radiant-heated substrates must not exceed a maximum surface temperature

of 85°F (29°C).

• Concrete ﬂoors should be tested for alkalinity. The allowable readings for

the installation of Armstrong ﬂooring are 5 to 9 on the pH scale.

Precautions:

• S-240 Epoxy Adhesive is recommended for SAFETY ZONE in areas that may

be exposed to frequent surface moisture and/or cooler temperatures.

• S-240 Epoxy Adhesive may also be used to install the ﬁrst 3 to 5 rows of

SAFETY ZONE when used in areas that will be affected by surface moisture

and/or cooler temperatures.

• Tiles are to be heated from the back only, never the face.

* Some previously manufactured asphaltic “cutback” adhesives contained asbestos (see warning

statement on page x). For removal instructions, refer to the Resilient Floor Covering Institute’s

publication Recommended Work Practices for Removal of Resilient Floor Coverings.

• Do not wash tile for at least 4 days after installation. This will allow the tile

to become well seated in the adhesive and prevent excess moisture and

cleaning agents from interfering with the adhesive bond.

• Products installed using the Tile-On System may have less resistance to

indentation. We strongly recommend the use of Armstrong Floor Protectors.

Fitting:

Before installing the material, plan the layout so tile joints fall at least 6"

(15.2 cm) away from subﬂoor/underlayment joints. Do not install over

expansion joints.

When installing over an existing resilient ﬂoor, plan the layout so the new

joints are a minimum of 6" (15.2 cm) away from the original seams. When

installing over tile ﬂoors, joints should fall in the center of the tile.

When installing 12" x 12" (30.5 cm x 30.5 cm) tiles, avoid having border pieces

less than 6" (15.2 cm) wide.

Abutting Different Gauges of Resilient Flooring: When installing thinner

gauge material next to thicker gauge materials, install thicker material ﬁrst

and then butt a 12" (30.5 cm) wide piece of S-153 Scribing Felt against the

thicker material. Adhere the Scribing Felt to the subﬂoor with S-235 Adhesive.

Use the ﬁne notching of the S-891 Trowel over nonporous substrates such as

existing resilient ﬂooring, and use the regular notching of the S-891 Trowel

over porous subﬂoors such as wood and concrete. Use S-184 Fast-Setting

Cement-Based Patch and Skim Coat or S-194 Patch, Underlayment and

Embossing Leveler to feather the edge of the S-153 Scribing Felt to the level of

the substrate. Allow the patch to dry completely before installing the ﬂooring.

Scribing Felt is not recommended to be used under the entire installation.

Adhesive Open Times and Trowel Notchings

Adhesive Open Time Working Time

S-515 Approximately 30 minutes or more 24 hours

S-525 Approximately 20 minutes or more 24 hours

S-700 Approximately 30 minutes or more 18 hours

S-750 Approximately 30 minutes or more 6 hours

S-240 Minimum 20 minutes 1 hours

NOTE: All adhesives except S-240 Epoxy Adhesive should be dry-to-touch

before installing tile. The amount of open time will vary according to

job conditions, temperature, humidity, air ﬂow and type of substrate. All

adhesives are applied with ﬁne notching [1/32" (0.8 mm) deep, 1/16" (1.6 mm)

wide, 5/64" (2 mm) apart].

Procedure:

See Adhesives, Seam Treatments and Grout.

When using tile from two or more cartons, check to be sure all pattern and lot

numbers are the same to ensure proper color match. On larger installations,

open several cartons and mix them as they are installed to help blend any

slight shade differences from one carton to the next.

Tile products with directional arrows on the back should be installed with the

arrows all pointing in the same direction.

• Tile Installed Using S-515, S-525, S-700 or S-750:

1. Line off entire area to be installed.

2. Apply the adhesive over the area not covering the chalk lines and using

the ﬁne notching of the S-891 Trowel. You may prefer to spread and install

one quarter of the room at a time.

3. Allow the adhesive to set until dry-to-touch (except S-240) following the

recommended open time. To test, press your thumb lightly on the surface

of the adhesive in several places. If the surface feels slightly tacky as your

thumb is drawn away and does not stick to your thumb, the adhesive is

ready for the installation.

4. Install the tile along the chalk lines, laying the ﬁeld area ﬁrst and then

ﬁtting in the border tile.

5. Roll all residential tile and SAFETY ZONE in both directions within the

adhesive working time using a 100-lb. roller.

6. Clean adhesive from the surface of the tile using a clean white cloth

dampened with a neutral detergent and water.

7. Tile should not be exposed to rolling load trafﬁc for at least 72 hours after

installation to allow setting and drying of the adhesive.

• SAFETY ZONE in Specialty Areas:

1. Line off entire area to be installed (Fig. 4).

2. Move chalk lines to one corner or end of the area farthest from the

doorway. These lines should be 2' or 3' from the wall depending on your

reach (Fig. 5).

3. Mix the entire contents of Part A and Part B together with a stirring

motion while at the same time lifting from the bottom. Mix thoroughly

for 3 to 5 minutes to a uniform color. Do not over mix. Never mix S-240

Epoxy Adhesive on the subﬂoor surface.

4. Immediately pour the entire unit of mixed adhesive onto the subﬂoor.

Do not leave mixed adhesive in cans because it shortens pot life and

S-240 Adhesive

Fig. 4 Fig. 5

working time, and may generate excessive heat. Maximum pot life of

the S-240 Epoxy Adhesive is approximately 10 minutes depending on

temperature and atmospheric conditions.

5. Apply S-240 Epoxy Adhesive for only 2 or 3 rows of tile. Working time of

S-240 Epoxy Adhesive is approximately 1 hour.

6. Tile may be placed into the adhesive immediately, but allowing 15 to 20

minutes of open time and ﬁtting border tile tightly will reduce tile shifting

and adhesive oozing. Do not allow the adhesive to dry completely.

7. Install tile with the arrows on the back of the tile pointing in the same

direction.

8. Roll tile in both directions within 1 hour of spreading S-240 Epoxy

Adhesive using a 100-lb. roller. Re-roll 1 hour later in both directions.

Remove adhesive residue from the surface of all the tile immediately

using a clean, white cloth dampened with neutral detergent and water.

Dried S-240 Epoxy Adhesive cannot be removed.

9. Do not work on newly adhered tile except to roll tile. Use a kneeling

board if necessary.

10. Repeat Steps 4 through 9 until the entire area is completed.

11. Do not allow trafﬁc on tile for 24 hours after installation.

12. Flooring should not be exposed to rolling load trafﬁc for at least 72 hours

after installation to allow setting and drying of the adhesive.

Armstrong® and Armstrong Logo are trademarks of AWI Licensing LLC.

All other marks are trademarks of Armstrong Flooring, Inc. or its subsidiaries.

Armstrong Flooring 52513031 Installation guide

Armstrong Flooring 52513031 Installation guide

Armstrong Flooring 52513031 Installation guide

Related papers

Other documents