Dynojet Power Commander III Installation guide

Category
Car kits
Type
Installation guide

Dynojet Power Commander III is an advanced fuel injection controller that allows you to optimize your ATV's performance by adjusting the air/fuel ratio and ignition timing. With the Power Commander III, you can:

  • Improve throttle response
  • Increase horsepower and torque
  • Smooth out the power delivery
  • Eliminate hesitation and bogging
  • Improve fuel economy
  • Run aftermarket exhaust systems and air filters without compromising performance

Dynojet Power Commander III is an advanced fuel injection controller that allows you to optimize your ATV's performance by adjusting the air/fuel ratio and ignition timing. With the Power Commander III, you can:

  • Improve throttle response
  • Increase horsepower and torque
  • Smooth out the power delivery
  • Eliminate hesitation and bogging
  • Improve fuel economy
  • Run aftermarket exhaust systems and air filters without compromising performance
i621-411www.powercommander.com 2007 Bombardier 800 Renegade - PCIII USB - 1
2007 Bombardier Renegade 800
Installation Instructions
Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
Parts List
1Power Commander
1USB Cable
1CD-ROM
1Installation Guide
1Power Adapter
2Power Commander Decals
2 Dynojet Decals
2 Velcro®Strip
1 Wire tap
1Alcohol Swab
You can also download the Power
Commander software and latest maps
from our web site at:
www.powercommander.com
The ignition MUST be turned
OFF before installation!
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
Button Adjustment Display
Faceplate Buttons
USB Port
Expansion Port
1 Remove the seat.
2Remove the right hand side covers
(Fig. A).
5Unplug the stock wiring harness from
the rear injector (Fig. C).
Fig. AFig. B
i621-411 www.powercommander.com 2007 Bombardier 800 Renegade - PCIII USB - 2
Remove these covers
Fig. C
Unplug stock harness
3Install the PCIII to the underside of
the airbox cover using the supplied
velcro. Make sure to clean both
surfaces with the alcohol swab before
attaching the unit (Fig. B).
Note: This picture shows the PCIII in the-
general location of the install. Place
the unit above this location.
4Route the PCIII wiring harness to the
right side of the ATV.
Air box cover
7Unplug the stock wiring harness from
the front injector (Fig. E).
8Route the ORANGE colored wires
from the PCIII to the left hand side of
the throttle body and go towards the
front injector.
9Plug the ORANGE colored wires
from the PCIII in-line of the stock
wiring harness and front fuel injector
(Fig. F).
Fig. E
Fig. F Fig. D
i621-411 www.powercommander.com 2007 Bombardier 800 Renegade - PCIII USB - 3
6Plug the YELLOW colored wires
from the PCIII in-line of the stock
wiring harness and rear fuel injector
(Fig. D).
PCIII connectors
Unplug stock harness
Stock connector
PCIII connectors
Stock connector
15 Route the ground wire from the PCIII
to the left hand side of the throttle
body and follow the stock ground
wires down to the right hand side of
the engine (Fig. J)
16 Attach the ground wire from the PCIII
to the common ground lug of the
engine (Fig. J).
17 Reinstall covers and seat.
Fig. H
i621-411 www.powercommander.com 2007 Bombardier 800 Renegade - PCIII USB - 4
12 Attach the supplied wire tap to the
WHITE/BROWN wire of the TPS
harness (Fig. H). Make sure the wire
tap is completely latched.
13 Plug the GREY wire from the PCIII
to the wire tap (Fig. H).
Note: It is recommended to use dielectric
grease on these connections.
14 Plug the wiring harness back onto the
TPS.
Fig. G
Grey wire
from PCIII
Wire tap
10 Locate the Throttle Position Sensor on
the rear of the throttle body (Fig. G).
11 Unplug the stock wiring harness from
the TPS.
Unplug
Fig. J
Ground wire
Bolt
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dynojet Power Commander III Installation guide

Category
Car kits
Type
Installation guide

Dynojet Power Commander III is an advanced fuel injection controller that allows you to optimize your ATV's performance by adjusting the air/fuel ratio and ignition timing. With the Power Commander III, you can:

  • Improve throttle response
  • Increase horsepower and torque
  • Smooth out the power delivery
  • Eliminate hesitation and bogging
  • Improve fuel economy
  • Run aftermarket exhaust systems and air filters without compromising performance

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI