Broan-NuTone HVDCT is a dual controller and timer. Use it to manage landscape lighting and mosquito repellent systems. The device allows for operation in two modes: time-based and sensor-based. Time-based operation allows you to program specific on and off times for both lighting and repellent systems. Sensor-based operation uses a solar sensor to automatically turn on the repellent system at dusk and keep it on for a specified number of hours. The controller can handle a maximum load of 36 watts on both the lighting and repellent circuits.
Broan-NuTone HVDCT is a dual controller and timer. Use it to manage landscape lighting and mosquito repellent systems. The device allows for operation in two modes: time-based and sensor-based. Time-based operation allows you to program specific on and off times for both lighting and repellent systems. Sensor-based operation uses a solar sensor to automatically turn on the repellent system at dusk and keep it on for a specified number of hours. The controller can handle a maximum load of 36 watts on both the lighting and repellent circuits.
© 2015 Broan-NuTone LLC
99528638D
Dual Controller / Timer
Controlador /
temporizador doble
Model number: HVDCT
Número de modelo: HVDCT
ASSEMBLY &WIRING INSTRUCTIONS
INSTRUCCIONES PARA
EL MONTAJE Y CABLEADO
English - See page 2
Español - Consulte la página 11
Page is loading ...
3
LED LIGHT CIRCUIT
VAPORIZER CIRCUIT
120 VAC 60 HZ
PRIMARY INPUT
120 VAC 60 HZ
PRIMARY INPUT
POWER
SUPPLY
POWER
SUPPLY
12 VAC OUTPUT
12 VAC OUTPUT
WARNING
To reduce the risk of fire, electric shock, or injury to persons,
observe the following:
• Use this fixture only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address or
telephone number listed in the warranty.
• Use only with a 12 VAC or 15 VAC listed low voltage landscape
lighting power supply; maximum secondary output is 300 watts.
• Total combined load of all landscape fixtures must not exceed 72
watts. (Maximum 36-watts per circuit.)
• Do not install within 10 feet (3.05 m) of pools, spas or fountains.
• This low voltage fixture must be installed in accordance with the
National Electrical Code (NEC) and local electrical codes.
• Use only UL / CSA approved low voltage landscape lighting cable,
suitable for direct burial and sunlight resistant.
• National Electrical Code states burial depth of the wiring must
not be more than 6” below grade surface. Check local codes to
ensure compliance with regulations.
• Low voltage cable must be protected by routing in close proximity
to the Haven fixture or next to a building structure such as a house
or deck.
• Fixture connections to the main low voltage cable must be
connected within 6” from the building structure or the Haven
fixture. Coil excess cable length within 6” from the fixture ground
stake.
Safety Warnings
4
Plan location
1 ] Locate the Dual Controller / Timer between the power supply (purchase
separately) and the Haven repellent (or lighted repellent) fixtures.
NOTE: Purchase power supply, low voltage cable and Haven lighted or
unlighted fixtures separately.
See Typical Low Voltage Wiring plans below to obtain best results.
SCHEMATIC FOR LIGHT &
MOSQUITO REPELLENT
FIXTURES
CDS
REPELLENT
LIGHT
SOLAR SENSOR
OPTIONAL
TIMER CONTROL
MODEL HVDCT
120 VAC 60 HZ
PRIMARY INPUT
POWER
SUPPLY 12 OR 15 VAC OUTPUT
LIGHT CIRCUIT
REPELLENT CIRCUIT
CDS
REPELLENT
LIGHT
SOLAR SENSOR
OPTIONAL
TIMER CONTROL
MODEL HVDCT
120 VAC 60 HZ
PRIMARY INPUT
POWER
SUPPLY 12 OR 15 VAC OUTPUT
OPTIONAL SECOND REPELLENT CIRCUIT OR
EXISTING LANDSCAPE LIGHTING CIRCUIT
(MAXIMUM LOAD IS 36 WATTS.)
REPELLENT CIRCUIT (MAXIMUM LOAD IS 36 WATTS.)
CAUTION
Do not exceed 36 watts on the repellent circuit or
the lighting circuit.
SCHEMATIC FOR
MOSQUITO REPELLENT
FIXTURES
5
AC 12V LIGHT REPELLENT CDS
INPUT
FROM
POWER
SUPPLY
LIGHT
CIRCUIT
CABLE
REPELLENT
CIRCUIT
CABLE
SOLAR
SENSOR
WIRES
If these terminals
are unused, additional
fixtures can be added.
Load must not
exceed 36W.
Load must not
exceed 36W.
Push down on tab,
insert wire and
release tab.
Make electrical connections
WARNING
To prevent electrical shock, disconnect power supply before
making fixture electrical connections.
1 ] Connect cables to controller / timer as shown.
Note: Make sure all cables are securely fastened.
6
Install Controller / Timer
1 ] Fasten controller timer to secure mounting surface with (2) 1-inch long
screws provided in parts bag.
2 ] Secure cables to the same surface to prevent them from being pulled
and disconnected. Cable clamps may be purchased separately. Do not
staple cables.
Install Solar Sensor (optional)
Install solar sensor if you wish to program the system using ambient light/dark,
rather than time of day.
NOTE: Make sure the solar sensor is located away from bushes,
obstructions, or artificial light source. Artificial lighting and other
obstructions will prevent sensor from operating properly.
1 ] Fasten solar sensor mounting bracket to secure mounting surface with
1-inch long screw provided in parts bag.
2 ] Secure cables to the same surface to prevent them from being pulled and
disconnected. Cable clamps may be purchased separately. Do not staple
cables.
7
Programming Instructions
1 ] Set Clock Time
• Press MODE, until
appears, wait 3 seconds,
Clock indicator glows; use
+ or – button to adjust
hours, noting AM and PM
indicators.
• Press MODE again,
indicator glows;
use + or – button to adjust
minutes
• Depressing and holding
down the + or - button will
cause time to scroll forward
or backward. Release
button to stop the scrolling.
• Press MODE until appears or wait 3 seconds to close “Set
Clock Time”
2 ] Set Repellent “On” and “Off” time via clock
• Press MODE until, appears for 3 seconds, Clock and
Repellent indicators glow; use + or - to adjust hours for repellent on,
noting AM and PM indicators
• Press MODE, Clock and Repellent indicators glow; use + or - to
adjust minutes for repellent on
• Press MODE until appears for 3 seconds, Clock and
Repellent indicators glow; use + or - to adjust hours for repellent off
• Press MODE, Clock and Repellent indicators glow; use + or - to
adjust minutes for repellent off
• Depressing and holding down the + or - button will cause time to
scroll forward or backward. Release button to stop the scrolling.
• Press MODE until appears or wait 3 seconds to close “Set
Clock Time”
PM
AM
Clock Repellent Light Solar
sensor
PROGRAM SETTINGS
MODE - +
LIGHT
ON/OFF
REPELLENT
ON/OFF
8
3 ] Set Repellent to turn on at dark via Solar Sensor, stay on for 1-12
hours (cancels out Light clock settings)
• Press MODE until, appears for 3 seconds, Repellent and
Solar Sensor indicators glow; use + or - to adjust number of hours
(1-12) for repellent to remain on after dusk.
• Depressing and holding down the + or- button will cause time to
scroll forward or backward. Release button to stop the scrolling.
• Press MODE, until appears or wait 3 seconds to close
“Repellent via Sensor”
4 ] Set Light “On” and “Off” time via clock
• Press MODE until, appears for 3 seconds, Clock and Light
indicators glow; use + or - to adjust hours for light on, noting AM
and PM indicators
• Press MODE, Clock and Light indicators glow; use + or - to adjust
minutes for light on
• Press MODE until appears for 3 seconds, Clock and
Repellent indicators glow; use + or - to adjust hours for light off
• Press MODE, Clock and Light indicators glow; use + or - to adjust
minutes for light off
• Depressing and holding down the + or- button will cause time to
scroll forward or backward. Release button to stop the scrolling.
• Press MODE until appears or wait 3 seconds to close “Set
Light Time”
5 ] Set Light to turn on at dark via Solar Sensor, stay on for 1-12
hours (cancels out Light clock settings)
• Press MODE until, appears for 3 seconds, Light and Solar
Sensor indicators glow; use + or- to adjust number of hours (1-12)
for light to remain on after dusk
• Depressing and holding down the + or- button will cause time to
scroll forward or backwards. Release button to stop the scrolling.
• Press MODE, until appears or wait 3 seconds to close
“Light via Sensor”
6 ] Close timer controller cover after programming has been
completed.
9
Troubleshooting
1 ] Entire system does not work –
• Make sure transformer is plugged into a working 120 volt wall
outlet.
• If wall outlet is switched, make sure it is turned on.
• Make sure the branch circuit breaker is not tripped.
• If transformer is so equipped, make sure its power switch is turned
on and timers are properly programmed.
• Make sure light and repellent circuits are connected to the
transformer.
• If the system is equipped with a solar sensor, make sure it’s located
away from bushes, other obstructions and away from artificial light
sources.
Broan-NuTone LLC
926 W. State Street
Hartford, WI 53027
IN U.S.A. CALL:
Customer Service:
1-888-336-3948
IN CANADA CALL:
1-877-896-1119
Technical Support:
1-888-336-6151
10
Limited Warranty
Warranty Period and Exclusions: Broan-NuTone LLC (the “Company”) warrants to the original consumer purchaser
of its product (“you”) that the product (the “Product”) will be free from material defects in the Product or its workmanship
for a period of three (3) years from the date of original purchase.
The limited warranty period for any replacement parts provided by the Company and for any Products repaired or
replaced under this limited warranty shall be the remainder of the original warranty period.
This warranty does not cover, cable connectors and repellent cartridges or repellent cartridge refills that may be
purchased separately and installed with the Product. This warranty also does not cover (a) normal maintenance and
service, (b) normal wear and tear, (c) any Products or parts which have been subject to misuse, abuse, abnormal
usage, negligence, accident, improper or insufficient maintenance, storage or repair (other than repair by the Company),
(d) damage caused by faulty installation, or installation or use contrary to recommendations or instructions, (f) damage
caused by exposure to salt air, (g) damage in transit, (h) natural wear of finish, (i) Products in commercial or nonresidential
use, or (j) damage caused by fire, flood or other act of God. This warranty covers only Products sold to original consumers
in the United States by the Company or U.S. distributors authorized by the Company.
This warranty supersedes all prior warranties and is not transferable from the original consumer purchaser.
No Other Warranties: This Limited Warranty contains the Company’s sole obligation and your sole remedy for defective
products. The foregoing warranties are exclusive and in lieu of any other warranties, express or implied. THE COMPANY
DISCLAIMS AND EXCLUDES ALL OTHER EXPRESS WARRANTIES, AND DISCLAIMS AND EXCLUDES ALL
WARRANTIES IMPLIED BY LAW, INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. To the extent that applicable law prohibits the exclusion of implied
warranties, the duration of any applicable implied warranty is limited to the period specified for the express warranty
above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you. Any oral or written description of the Product is for the sole purpose of identifying it and shall not be construed
as an express warranty.
Whenever possible, each provision of this Limited Warranty shall be interpreted in such manner as to be effective and
valid under applicable law, but if any provision is held to be prohibited or invalid, such provision shall be ineffective only
to the extent of such prohibition or invalidity, without invalidating the remainder of such provision or the other remaining
provisions of the Limited Warranty.
Remedy: During the applicable limited warranty period, the Company will, at its option, provide replacement parts for, or
repair or replace, without charge, any Product or part thereof, to the extent the Company finds it to be covered by and
in breach of this limited warranty under normal use and service. The Company will ship the repaired or replaced Product
or replacement parts to you at no charge. You are responsible for all costs for removal, reinstallation and shipping,
insurance or other freight charges incurred in the shipment of the Product or part to the Company. If you must send
the Product or part to the Company, as instructed by the Company, you must properly pack the Product or part—the
Company is not responsible for damage in transit. The Company reserves the right to utilize reconditioned, refurbished,
repaired or remanufactured Products or parts in the warranty repair or replacement process. Such Products and parts
will be comparable in function and performance to an original Product or part and warranted for the remainder of the
original warranty period.
Exclusion of Damages: THE COMPANY’S OBLIGATION TO PROVIDE REPLACEMENT PARTS, OR REPAIR OR
REPLACE, AT THE COMPANY’S OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS
LIMITED WARRANTY AND THE COMPANY’S SOLE AND EXCLUSIVE OBLIGATION. THE COMPANY SHALL
NOT BE LIABLE FOR INCIDENTAL, INDIRECT, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF
OR IN CONNECTION WITH THE PRODUCT, ITS USE OR PERFORMANCE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which
vary from state to state.
This warranty covers only replacement or repair of defective Products or parts thereof at the Company’s main facility and
does not include the cost of field service travel and living expenses.
Any assistance the Company provides to or procures for you outside the terms, limitations or exclusions of this limited
warranty will not constitute a waiver of such terms, limitations or exclusions, nor will such assistance extend or revive
the warranty.
The Company will not reimburse you for any expenses incurred by you in repairing or replacing any defective Product,
except for those incurred with the Company’s prior written permission.
How to Obtain Warranty Service: To qualify for warranty service, you must (a) notify the Company at the address or
telephone number stated below within seven (7) days of discovering the covered defect, (b) give the model number and
part identification and (c) describe the nature of any defect in the Product or part. At the time of requesting warranty
service, you must present evidence of the original purchase date. If you cannot provide a copy of the original written
limited warranty, then the terms of the Company’s most current written limited warranty for your particular product will
control. The most current limited written warranties for the Company’s products can be found at www.nutone.com.
Broan-NuTone LLC 926 West State Street, Hartford, WI 53027 www.nutone.com 888-336-3948
Broan-NuTone Canada ULC Mississauga, Ontario Canada L5T 1H9 www.nutone.ca 888-882-7626
Page is loading ...
Page is loading ...
13
DIAGRAMA PARA LOS
ACCESORIOS DEL REPELENTE
DE MOSQUITOS Y LA LUZ
CDS
REPELENTE
LUZ
SENSOR SOLAR
CONTROL OPCIONAL
DEL TEMPORIZADOR
MODELO HVDCT
ENTRADA PRINCIPAL
120 VCA 60 HZ
FUENTE DE
ALIMENTACIÓN SALIDA DE 12 O 15 VCA
CIRCUITO DE LA LUZ
CIRCUITO DEL REPELENTE
CDS
REPELENTE
LUZ
SENSOR SOLAR
CONTROL OPCIONAL
DEL TEMPORIZADOR
MODELO HVDCT
ENTRADA PRINCIPAL
120 VCA 60 HZ
FUENTE DE
ALIMENTACIÓN
SALIDA DE 12 O 15 VCA
CIRCUITO DEL SEGUNDO REPELENTE OPCIONAL
O CIRCUITO DE LA LUZ DECORATIVA EXISTENTE
(LA CARGA MÁXIMA ES DE 36 VATIOS)
CIRCUITO DEL REPELENTE
(LA CARGA MÁXIMA ES DE 36 VATIOS)
PRECAUCIÓN
No exceda de 36 vatios en el circuito del repelente o en el
circuito de la luz.
DIAGRAMA PARA LOS
ACCESORIOS DEL
REPELENTE DE MOSQUITOS
Planifique la ubicación
1 ] Ubique el controlador doble / temporizador entre la fuente
de alimentación (se compra por separado) y los accesorios
de repelente (o repelente con luz) Haven.
NOTA: Compre por separado la fuente de alimentación, el cable de
bajo voltaje y los accesorios con luz o sin luz Haven.
Consulte los planes típicos de cableado de bajo voltaje a continuación para
obtener los mejores resultados.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
20
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Broan-NuTone HVDCT is a dual controller and timer. Use it to manage landscape lighting and mosquito repellent systems. The device allows for operation in two modes: time-based and sensor-based. Time-based operation allows you to program specific on and off times for both lighting and repellent systems. Sensor-based operation uses a solar sensor to automatically turn on the repellent system at dusk and keep it on for a specified number of hours. The controller can handle a maximum load of 36 watts on both the lighting and repellent circuits.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
Other documents
-
NuTone Haven HVLFABR Assembly Instructions Manual
-
NuTone Haven HVK400 User manual
-
Jocel JVAP030511 User manual
-
Broan 82W Installation guide
-
ThermaCELL MR300 User manual
-
Sony XDP-MU110 User manual
-
Sony DSC-W650 Operating instructions
-
Sony DSC-W620 Operating instructions
-
-