Niigata seiki WCDI-160D User manual

Brand: Niigata seiki

Model: WCDI-160D

Type: User manual

This manual is also suitable for

ABS/SET

MIN CAL

ZERO/ON

ABS/SET

MIN CAL

ZERO/ON

ABS

Model：WCDI-50D/WCDI-100D/WCDI-160D ＜combined＞

Clamp

Screw

Not including quantization error (±1 count)

Loosen the Clamp Screw and

insert the Digital Indicator into

the gauge body. Tighten the

Clamp Screw to secure.

After attaching, press the [ZERO/

ON] Button on the Digital Indicator

to turn on power. Confirm that the

displayed reading changes by

gently squeezing the measurement

head. If necessary, adjust the depth

that the Digital Indicator is inserted

into the gauge body.

①

②Select the combination of Sub Rod (WCD-160 only) Extension

Rod and Washers for the dimension you want to measure.

Remove the Rod Adj. Nut put on the desired Sub Rod, Rod, and

Washers, and secure with the Extension Rod Mounting Nut.

ASSEMBLY

INSERT

Accessories

This is a precision instrument, handle with

care.

Do not disassemble or modify.

Keep instrument away from water and oil.

Use only with supplied Extension Rods

and Washer.

Keep instrument away from direct sunlight

and high temperatures such as in a car, or

near a stove or heat source.

After use, remove any dirt or cutting chips

and apply rust preventative oil to to

Extension Rod and Washer. When not in

use store in supplied storage case.

This product is for measuring inside

diameter; use only as directed. Improper

use may cause accident or injury.

Avoid using in high electric fields, such as

near fluorescent lights or switching power

supplies. Electrical interference may

cause incorrect readings.

NOTICE

INSERTING BATTERY

Pull out the case from the two

side edges to remove. Insert

battery with (＋) side facing

down.

Use only CR2032 type lithium

button cell.

NOTICE

Battery

Case

Battery

Extension Rod

Sub Rod

only

Handle

Extension

Rod

Mounting

Nut

Shaft

Probe Tip

Length below Handle:

Measurement

Head

Washers

Guide

Ex. Rod Nut Ex. Rod

Ex. Rod

Washer Washer

Washer Sub Rod

Examples

Measure:

(1 each size)

Extension Rods

pieces

Sub Rod x only

Battery Lithium button cell, 1x (for test)

DIGITAL BORE GAUGE

Thank you for purchasing the Digital Bore Gauge.

Please read this manual thoroughly before use for proper operation.

Instruction Manual

Including supplied Digital Gauge

PART IDENTIFICATION SPECIFICATIONS

Model No.

Measuring Range

Resolution

Wide Range Acc'y

Adjacent Error

Repeat Accuracy

Washer

Single Stroke Range

Weight

Display

[]

Button

[] Button

[]Button

[]

Button

Clamp

Screw

Gauge

Digital Indicator

Cap Not Used

"0.01" indicates the resolution

of the display's digital bar

graph. The bar graph display

will change with each 0.01mm

change in the measured

value.

ACCESSORIES

Please select combination with fewest number of Washers.

Measure:

ABS/SET

MIN CAL

ZERO/ON

ABS

ABS/SET

MIN CAL

ZERO/ON

39.998

ABS/SET

MIN CAL

ZERO/ON

ABS

ABS/SET

MIN CAL

ZERO/ON

ABS

MEASUREMENT

Fig. Fig. Fig.

For accurate measurements, follow the procedure described below.

①In cross section perpendicular to the axis of the bore, as shown in Figure 1, position the gauge along diameter ⓐ. This is the

maximum distance, and at this point the Indicator will read the maximum value. The Guide will automatically position the

Measurement Head to diameter ⓐ when inserted.

②In cross section parallel to to the axis of the bore through diameter ⓐ, position the indicator to minimize the distance ⓑ. (Figure 2)

In this position the Indicator will read the minimum value. This position must be manually determined by pivoting the Gauge as

shown in Figure 3 while watching the Indicator to find the minimum value.

OPERATION

①Before use, please make sure the Measurement Head components are not loose and tighten if necessary.

②Clean the Measurement Head and the ID of a Ring Gauge Standard using parts cleaner or cleaning solution.

③Press the [ZERO/ON] Button to turn on power. ※ A long press to the [ZERO/ON] Button will turn power off.

ABSOLUTE MODE (ABS)

Turn on power. If the “ ” or “

※ Measure absolute dimension of workpiece

” symbols are displayed on the LCD, press the [MIN] Button to turn off.

Adjust the “SET” value of the Bore Gauge to match the ID of the Ring Gauge Standard. Press and hold the [ABS/SET] Button until

“SET” blinks on the display.

Continue holding the [ABS/SET] Button and the display character to the left will blink. Use a short press of the [ABS/SET] Button to

change the value, and a long press to change the character being modified. Repeat this process to enter the dimension of the Ring

Gauge Standard on the LCD display. (Figure 4)

When the value is entered the flashing position will return to “SET”. A short

press of the [ABS/SET] Button to turn off the flashing.

COMPARATIVE MEASUREMENTS

Difference between workpiece and reference

Turn on power. If “ ” or “ ” symbols are displayed on the LCD,

press the [MIN] Button to turn off. If “ABS” is displayed press the

[ABS/SET] Button to turn off.

Insert the Measurement Head into the Ring Gauge Standard and press

[MIN] Button to put the Indicator into minimum-mode. Slowly pivot the

gauge (Figure 3) to display the minimum value.

Remove the gauge from the Ring Gauge and press the [CAL] button

until “OK” is momentarily displayed.

Preparation for measurement is now complete.

Put the gauge into the workpiece to be measured, and pivot the gauge

slowly. (Figure 3) The LCD will display the difference between the

measured workpiece and the calibration standard. (Figure 6)

Press the [ON/ZERO] Button momentarily to reset display in preparation

to measure the next workpiece.

⑤

⑥

⑦

Insert the Measurement Head into the Ring Gauge Standard and press

the [MIN] Button to put the Indicator into minimum-mode. Slowly pivot

the gauge (Figure 3) to display the minimum value.

Remove the gauge from the Ring Gauge and press the [CAL] button

until “OK” is momentarily displayed. Preparation for measurement is

now complete.

Put the gauge into the workpiece to be measured, and pivot the gauge

slowly. (Figure 3) The LCD will display the measured value. (Figure 5)

※Press the [ON/ZERO] Button momentarily to reset display in

preparation to measure the next workpiece.

Ring Gauge

Standard

Work-

piece

Set to match

Workpiece I.D. value

Diff. between Work-

piece and Reference

Fig.

Work-

piece

TROUBLESHOOTING

ERROR CORRECTIVE ACTION

LCD does not display

Displayed value is unstable

Display is not clear

Cycle power by removing and

replacing battery.

Replace battery with new one.

●

●●

If problem persists, or if you have any questions,

please contact distributor or place of purchase.

Please note, manufacturer is unable to respond to

inquires or provide service directly. Please contact

distributor or place of purchase.

Niigata Seiki Co., Ltd.

61522 , Tsukanome, Sanjo, Niigata, Japan 9550055

TEL: +81256315670 FAX: +81256397730

MAIL: intl.sale s@niigataseiki.co.jp

URL http://www.niigataseiki.co.jp

Niigata seiki WCDI-160D User manual

Brand: Niigata seiki

Model: WCDI-160D

Type: User manual

This manual is also suitable for

Download PDF

report

Niigata seiki WCDI-160D User manual

This manual is also suitable for

Niigata seiki WCDI-160D User manual

Related papers

Other documents