QUANTA S200-X12TS User manual

STRATOS S200 Series

S200-X12TS

2-Socket General Purpose

1U Server

8VHUV Guide

Document Version: 1.0

CONVENTIONS

Conventions

Several different typographic conventions are used throughout

this manual. Refer to the following examples for common

usage.

Bold type face denotes menu items, buttons and application

names.

Italic type face denotes references to other sections, and the

names of the folders, menus, programs, and files.

<Enter> type face denotes keyboard keys.

WARNING!

Warning information appears before the text it references and

should not be ignored as the content may prevent damage to

the device.

CAUTION!

CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES, SIMILAR TO

NOTES AND WARNINGS. CAUTIONS, HOWEVER, APPEAR IN CAPITAL

LETTERS AND CONTAIN VITAL HEALTH AND SAFETY INFORMATION.

Note:

Highlights general or useful information and tips.

!

ACRONYMS

Acronyms

TERM DEFINITION

A/D Analog to Digital

ACPI Advanced Configuration and Power Interface

ASF Alerting Standard Forum

Asserted

Active-high (positive true) signals are asserted when in

the high electrical state (near power potential). Active-

low (negative true) signals are asserted when in the

low electrical state (near ground potential).

BIOS Basic Input/Output System

BIST Built-In Self Test

BMC

At the heart of the IPMI architecture is a microcontroller

called the Baseboard management controller (BMC)

Bridge

Circuitry connecting one computer bus to another,

allowing an agent on one to access the other

BSP Bootstrap processor

Byte 8-bit quantity

CLI Command Line Interface

CMOS

In terms of this specification, this describes the PC-AT

compatible region of battery-backed 128 bytes of mem-

ory, which normally resides on the baseboard

CPU Central Processing Unit

Deasserted

A signal is deasserted when in the inactive state.

Active-low signal names have “_L” appended to the

end of the signal mnemonic. Active-high signal names

have no “_L” suffix. To reduce confusion when referring

to active-high and active-low signals, the terms one/

zero, high/low, and true/false are not used when

describing signal states.

DTC Data Transfer Controller

EEPROM

Electrically Erasable Programmable Read-Only Mem-

ory

EMP Emergency Management Port

FRU Field Replaceable Unit

GB 1024 MB.

GPIO General Purpose Input/Out

HSC Hot-Swap Controller

Hz Hertz (1 cycle/second)

I

2

C

Inter-Integrated Circuit bus

IANA Internet Assigned Numbers Authority

IBF Input buffer

ICH I/O Controller Hub

ICMB Intelligent Chassis Management Bus

IERR Internal Error

IP Internet Protocol

IPMB Intelligent Platform Management Bus

T

ERM DEFINITION

ACRONYMS

IPMI Intelligent Platform Management Interface

ITP In-Target Probe

KB 1024 bytes.

KCS Keyboard Controller Style

KVM Keyboard, Video, Mouse

LAN Local Area Network

LCD Liquid Crystal Display

LCT Lower Critical Threshold

LED Light Emitting Diode

LNCT Lower Non-Critical Threshold

LNRT Lower Non-Recoverable Threshold

LPC Low Pin Count

LSI Large Scale Integration

LUN Logical Unit Number

MAC Media Access Control

MB 1024 KB

MD2 Message Digest 2 – Hashing Algorithm

MD5

Message Digest 5 – Hashing Algorithm – Higher Secu-

rity

Ms Milliseconds

Mux Multiplexer

NIC Network Interface Card

NMI Non-maskable Interrupt

NM Node Management

OBF Output buffer

OEM Original Equipment Manufacturer

T

ERM DEFINITION

Ohm Unit of electrical resistance

PDB Power Distribution Board

PEF Platform Event Filtering

PEP Platform Event Paging

PERR Parity Error

POH Power-On Hours

POST Power-On Self Test

PWM Pulse Width Modulation

RAC Remote Access Card

RAM Random Access Memory

RMCP Remote Management Control Protocol

ROM Read Only Memory

RTC

Real-Time Clock. Component of the chipset on the

baseboard.

RTOS Real Time Operation System

SCI Serial Communication Interface

SDC SCSI Daughter Card

SDR Sensor Data Record

SEEPROM

Serial Electrically Erasable Programmable Read-Only

Memory

SEL System Event Log

SERR System Error

SMBus

A two-wire interface based on the I

2

C protocol. The

SMBus is a low-speed bus that provides positive

addressing for devices, as well as bus arbitration

SMI

Server Management Interrupt. SMI is the highest prior-

ity non-maskable interrupt

T

ERM DEFINITION

ACRONYMS

SMM Server Management Mode

SMS Server Management Software

SNMP Simple Network Management Protocol

SOL Serial Over LAN

UART Universal Asynchronous Receiver/Transmitter

UCT Upper Critical Threshold

UDP User Datagram Protocol

UNCT Upper Non-Critical Threshold

UNRT Upper Non-Recoverable Threshold

WDT Watchdog Timer

Word 16-bit quantity

T

ERM DEFINITION

SAFETY INFORMATION

Safety Information

Important Safety Instructions

Read all caution and safety statements in this document before

performing any of the instructions.

Warnings

Heed safety instructions: Before working with the server,

whether using this manual or any other resource as a refer-

ence, pay close attention to the safety instructions. Adhere to

the assembly instructions in this manual to ensure and maintain

compliance with existing product certifications and approvals.

Use only the described, regulated components specified in this

manual. Use of other products / components will void the UL

listing and other regulatory approvals of the product and will

most likely result in non-compliance with product regulations in

the region(s) in which the product is sold.

System power on/off: The power button DOES NOT turn off

the system AC power. To remove power from system, you must

unplug the AC power cord from the wall outlet. Make sure the

AC power cord is unplugged before opening the chassis, add-

ing, or removing any components.

Hazardous conditions, devices and cables: Hazardous elec-

trical conditions may be present on power, telephone, and com-

munication cables. Turn off the server and disconnect the

power cord, telecommunications systems, networks, and

modems attached to the server before opening it. Otherwise,

personal injury or equipment damage can result.

Electrostatic discharge (ESD) and ESD protection: ESD can

damage drives, boards, and other parts. We recommend that

you perform all procedures in this chapter only at an ESD work-

station. If one is not available, provide some ESD protection by

wearing an antistatic wrist strap attached to chassis ground any

unpainted metal surface on the server when handling parts.

ESD and handling boards: Always handle boards carefully.

They can be extremely sensitive to electrostatic discharge

(ESD). Hold boards only by their edges. After removing a board

from its protective wrapper or from the server, place the board

component side up on a grounded, static free surface. Use a

conductive foam pad if available but not the board wrapper. Do

not slide board over any surface.

Installing or removing jumpers: A jumper is a small plastic

encased conductor that slips over two jumper pins. Some jump-

ers have a small tab on top that can be gripped with fingertips

or with a pair of fine needle nosed pliers. If the jumpers do not

have such a tab, take care when using needle nosed pliers to

remove or install a jumper; grip the narrow sides of the jumper

SAFETY INFORMATION

with the pliers, never the wide sides. Gripping the wide sides

can damage the contacts inside the jumper, causing intermittent

problems with the function controlled by that jumper. Take care

to grip with, but not squeeze, the pliers or other tool used to

remove a jumper, or the pins on the board may bend or break.

REVISION HISTORY

Revision History

Refer to the table below for the updates made to this manual.

Copyright

including all photographs, illustrations and software, is pro-

tected under international copyright laws, with all rights

reserved. Neither this manual, nor any of the material contained

herein, may be reproduced without the express written consent

of the manufacturer. All trademarks and logos are copyrights of

their respective owners.

Version 1.0 / Janunary 23, 2014

Disclaimer

The information in this document is subject to change without

notice. The manufacturer makes no representations or warran-

ties with respect to the contents hereof and specifically dis-

claims any implied warranties of merchantability or fitness for

any particular purpose. Furthermore, the manufacturer reserves

the right to revise this publication and to make changes from

time to time in the content hereof without obligation of the man-

ufacturer to notify any person of such revision or changes.

For the latest information and updates please refer to

www.QuantaQCT.com

All the illustrations in this technical guide are for reference only

and are subject to change without prior notice.

DATE CHAPTER UPDATES

About the Server

Chapter 1

ABOUT THE SERVER INTRODUCTION

1-1

1.1. Introduction

Main Features

Quanta STRATOS S200-X12TS is a 2-socket general purpose

1U server, supporting two Intel

®

Xeon

®

processor E5-2400

family and twelve DDR3 DIMM slots. It is designed with opti-

mized cost suitable for fast growing small and medium busi-

nesses who need more performance head rooms to scale up

from 1-socket platforms.

Specifications

S200-X12TS Specification

SPECIFICATION DESCRIPTION

Form Factor X1 (1U Chassis)

Chassis Size (L x W x

H)

 728 mm x 438 mm x 43.2 mm

 28.66" x 17.24" x 1.7"

Mainboard Size (W x

L )

 165 mm x 416.6 mm

 6.5" x 16.4" (half-width)

Processor

(2) Intel

®

Xeon

®

processor E5-2400 family per

node, up to 95W

Chipset

Intel

®

C602

SAS Controller

2.5” 1 to 1 SKU

 LSI SAS controller

 Quanta LSISAS 2008 or 2308 Mezzanine

card

 Quanta LSISAS 2108 or 2208 Mezzanine

card (optional)

3.5” 1 to 1 SKU

 Intel

®

SAS controller

 Intel

®

C602 upgrade ROM #1 (optional)

 Intel

®

C602 upgrade ROM #2 (optional)

or

 LSI SAS controller

 Quanta LSISAS 2008/2308/2108/2208

Mezzanine card (optional)

2.5” Expander SKU

 [LSI SAS controller]

 Quanta LSISAS 2008 or 2308 Mezzanine

card

 Quanta LSISAS 2108 or 2208 Mezzanine

card (optional)

S200-X12TS Specification (Continued)

SPECIFICATION DESCRIPTION

ABOUT THE SERVER MAIN FEATURES

1-2

Memory

 (12) DDR3 800/1066/1333/1600 MHz

 ECC UDIMM/RDIMM/LRDIMM slots per

node, up to 384 GB

Storage

2.5” 1 to 1 SKU

 (10) 2.5" hot-plugable HDD(Mezz *8+ AHCI

*2 6Gb) + (2) fixed SATAII (AHCI 3Gb) or

SSD (AHCI 3Gb)

 (1) USB Flash Module for OS installation per

node (optional)

3.5” 1 to 1 SKU

 (4) 3.5" hot-plugable HDD(SCU 3Gb) + (2)

fixed SATAIII (AHCI 6Gb) or SSD (AHCI 6Gb)

+ (1) fixed SSD front end

 (1) USB Flash Module for OS installation per

node (optional)

2.5” Expander SKU

 (10) 2.5" hot-plugable SATA/SAS

HDD(expander 6Gb) + (2) fixed SATAII (AHCI

6Gb) or SSD (AHCI 6Gb)

 (1) USB Flash Module for OS installation per

node (optional)

HDD Backplane

2.5” 1 to 1 SKU / 3.5” 1 to 1 SKU

 1 to 1

2.5” Expander SKU

 Expander

S200-X12TS Specification (Continued)

SPECIFICATION DESCRIPTION

PCIe Expansion Slot

 (1) Riser w/ Linking - PCIe x8 G2 riser slot

10GbE SFP+ Mezzanine card slot & Low pro-

file x8 slot

 (1) PCIe x8 G2 Quanta LSISAS/RAID Mezza-

nine card slot

SW RAID Options

2.5” 1 to 1 SKU / 2.5” Expander SKU

 LSI SW RAID

 Quanta LSISAS 2008/2308 mezzanine

card for RAID 0/1/10

3.5” 1 to 1 SKU

 Intel SW RAID

 Intel RSTe SATA RAID 0/1/10/5

 Intel C602 upgrade ROM #1 SAS RAID 0/

1/10 (optional for SCU)

 Intel C602 upgrade ROM #2 SAS RAID 0/

1/10/5 (optional for SCU)

or

 LSI SW RAID

 Quanta LSISAS 2008/2308 mezzanine

card for RAID 0/1/10 (optional)

S200-X12TS Specification (Continued)

SPECIFICATION DESCRIPTION

ABOUT THE SERVER MAIN FEATURES

1-3

HW RAID Options

2.5” 1 to 1 SKU / 3.5” 1 to 1 SKU

 Quanta LSISAS2108/2208 PD-8 mezzanine

card for RAID 0/1/10/5 (optional)

 Quanta LSISAS2108/2208 PD-8 mezzanine

card + LSI RAID 6 Key for RAID 0/1/10/5/6/

50/60 (optional)

2.5” Expander SKU

 Quanta LSISAS2108/2208 PD-16 mezzanine

card for RAID 0/1/10/5 (optional)

 Quanta LSISAS2108/2208 PD-16 mezzanine

card + LSI RAID 6 Key for RAID 0/1/10/5/6/

50/60 (optional)

Network

 (2) Intel

®

Powerville I350GbE RJ45 ports

 (1) Quanta 10GbE SFP+ dual port mezza-

nine card (optional)

Management Port

(1) Dedicated 10/100 BASE-T RJ45 manage-

ment port per node

Integrated Graphics

BMC

Aspeed AST2300 8MB DDR3 Video memory

Rear I/O

 (2) USB 2.0 ports

 (1) VGA port

 (1) RS232 serial Port

 (2) GbE RJ45 ports

 (1) 10/100 BASE-T RJ45 management port

S200-X12TS Specification (Continued)

SPECIFICATION DESCRIPTION

Power Supply

 (1) 750W high efficiency PSU

 (1) 750W high efficiency redundant PSU

(optional)

TPM NA

RoHS Yes

Intel Node Manage-

ment support

Yes

System Management

IPMI v2.0 Compliant, on board "KVM over IP"

support

S200-X12TS Specification (Continued)

SPECIFICATION DESCRIPTION

ABOUT THE SERVER PACKAGE CONTENTS

1-4

1.2. Package Contents

The following list includes the package components:

 1U chassis system

 Mainboard modules

 2 x Processor heatsinks

 Power supply

 Power cord (optional)

 CD (technical guide included)

 Rail kit

Important:

Server configurations may vary. Confirm your sales representa-

tive for the exact items included in your order.

ABOUT THE SERVER A TOUR OF THE SYSTEM

1-5

1.3. A Tour of the System

System Overview

The S200-X12TS is available as a 2.5” or a 3.5” form factor.

2.5” HDD System

2.5” HDD System Component Overview

1

2

4

5

6

7

3

2.5” SKU System Component Description

NO.ITEM DESCRIPTION

1 PSUs 2x power supply units (PSU)

2 2.5” or 3.5” HDD 2.5” or 3.5” fixed HDDs

3 Battery System battery

4 Chassis System chassis

5 2.5 HDDs 2.5” hard disk drive (HDD) cage

6 System fan 4x system fan modules

7 MB module Mainboard module

ABOUT THE SERVER SYSTEM FRONT FEATURES

1-6

3.5” HDD System

3.5” HDD System Component Description

System Front Features

Configuration

2.5” HDD Configuration

3.5” SKU System Component Description

NO.ITEM DESCRIPTION

1 PSUs (2) power supply units (PSU)

2 2.5” or 3.5” HDD 2.5” or 3.5” fixed HDDs

3 Battery System battery

1

2

4

5

6

7

3

4 Chassis System chassis

5 3.5 HDDs 3.5” hard disk drive (HDD) cage

6 System fan (4) System fan modules

7 MB module Mainboard module

3.5” SKU System Component Description (Continued)

NO.ITEM DESCRIPTION

1

2

ABOUT THE SERVER SYSTEM FRONT FEATURES

1-7

3.5” HDD Configuration

Control Panel

2.5” HDD SKU Control Panel

2.5” HDD SKU Control Panel Features

System Configuration

ITEM NAME DESCRIPTION

1 Control Panel Control system

2 HDD Bays HDDs arrays

1

2

2.5” HDD SKU Control Panel Features

ITEM ICON NAME DESCRIPTION

1 Event LED

Amber Blinking:

Critical failure: fan, voltage, tempera-

ture state

Non-critial failure: fan, voltage, tem-

perature state, CPU, thermal trip

Off: SEL cleared, DC off, last pending

warning/error de-asserted

2 LAN1/2 LED

Green On, link

Green Blinking, LAN access

1

2

3

4

ABOUT THE SERVER SYSTEM FRONT FEATURES

1-8

3.5” HDD SKU Control Panel

3.5” HDD SKU Control Panel Features

3

Power But-

ton with LED

Green On

Based on System Off, Push Button to

PSU and System On

Based on System On, Push Button to

PSU and System Off

4

ID button

with LED

Blue On, selected unit ID

Off, no ID requested

3.5” HDD SKU Control Panel Features

ITEM ICON NAME DESCRIPTION

1

Front USB

ports

Connect USB devices to these ports

2.5” HDD SKU Control Panel Features (Continued)

ITEM ICON NAME DESCRIPTION

123 456 7

2

Reset But-

ton with

LED

Base system On

Push button to Reset system

3MGMT LED

Green On, link

Green Blinking, LAN access

4

LAN 2/1

LED

Green On, link Green Blinking, LAN

access

5

HDD Activ-

ity LED

Green Blinking, HDD access Off, no

access

6 Event LED

Amber Blinking:

Critical failure: fan, voltage, temperature

state

Non-critial failure: fan, voltage, tempera-

ture state, CPU, thermal trip

Off: SEL cleared, DC Off, last pending

warning/error de-asserted

7

ID Button

with LED

Blue On, selected unit ID

Off, no ID requested

8

Power but-

ton with

LED

Green On

Based on System Off, Push Button to

PSU and System On

Based on System On, Push Button to

PSU and System off

3.5” HDD SKU Control Panel Features (Continued)

ITEM ICON NAME DESCRIPTION

ABOUT THE SERVER SYSTEM REAR FEATURES

1-9

System Rear Features

Configuration

System Rear Configuration

I/O Features

System Rear I/O Features

System Rear Configuration

NO.ITEM DESCRIPTION

1

Main Power Sup-

ply Unit

Main power supply unit (PSU)

2 Dummy PSU Dummy PSU

3 Mainboard Mainboard (MB)

2

1 3

S200-X12TS System I/O Features

ITEM FEATURE DESCRIPTION

1 10GbE SFP+ mezzanine Port Optional

2 PSU Power supply unit

3 Serial port

Connect serial devices to this

port

4 LAN LAN access

5 Dedicated Management LAN Port

6 VGA port Connect a monitor to this port

7USB port

USB ports (2.0 compliant)

Note:

The width of the USB drive

needs to be lower than 17mm

to avoid interfering with the use

of the VGA port.

8 Power button On/Off power to the module

1

847623

5

ABOUT THE SERVER POWER SUB-SYSTEM

1-10

Power Sub-System

PSU Description

A system can have two power supply units (PSU). The primary

PSU and a redundant backup. The redundant backup is

optional.

LED Status Definitions

I/O LED Description

Power Supply Units by Model

MODEL PSU AC INPUT

S200-X12TS

(1) 750W high efficiency PSU,

100-240VAC 50/60Hz

110/220V

Note:

To use mainboard modules other than the models listed make

sure to contact the system dealer first and obtain authorized

approval.

PSU

I/O LED Description - 1GbE LAN

ICON NAME COLOR

CONDITI

ON

DESCRIPTIO

N

Identification LED

Blue On

Unit

selected for

identification

-- Off

No identifi-

cation

requested

ABOUT THE SERVER LED STATUS DEFINITIONS

1-11

LAN1

LED

(Upper)

Link/Act

Green On LAN Link

Green Black Blinking

LAN access

(off when

there is traf-

fic)

-- Off Disconnect

Speed

Green On

Link speed

is 100Mbits/

sec

Amber On

Link speed

is

1000Mbits/

sec

-- Off

Off, link

speed is

10Mbits/sec

I/O LED Description - 1GbE LAN (Continued)

ICON NAME COLOR

CONDITI

ON

DESCRIPTIO

N

LAN2

LED

(Lower)

Link/Act

Green On LAN Link

Green Black Blinking

LAN access

(off when

there is traf-

fic)

-- Off Disconnect

Speed

Green On

Link speed

is 100Mbits/

sec

Amber On

Link speed

is

1000Mbits/

sec

-- Off

OFF, link

speed is

10Mbits/sec

Service

Port

(LAN 3)

LED

Link/Act

Green On LAN Link

Green Black Blinking

LAN access

(off when

there is traf-

fic)

-- Off Disconnect

Speed Green On

Link speed

is 10/100/

1000Mbits/

sec

I/O LED Description - 1GbE LAN (Continued)

ICON NAME COLOR

CONDITI

ON

DESCRIPTIO

N

Page is loading ...

QUANTA S200-X12TS User manual

QUANTA S200-X12TS User manual

Related papers

Other documents