EVOLUTION POWERSPORTS 925FP0202 Front Grille Bezel for Polaris RZR 200 User manual

Brand: EVOLUTION POWERSPORTS

Model: 925FP0202 Front Grille Bezel for Polaris RZR 200

Type: User manual

EVOLUTION POWERSPORTS 925FP0202 Front Grille Bezel for Polaris RZR 200:

This grille bezel kit is designed to enhance the appearance and durability of your Polaris RZR 200. Made from high-quality materials, it provides excellent protection against damage from debris and other hazards. Installation is straightforward, requiring only basic tools and following the provided instructions.

The bezel is available in three colors: raw, red, and white, allowing you to customize the look of your vehicle. It fits seamlessly with the existing front clip and adds a stylish accent.

EVOLUTION POWERSPORTS 925FP0202 Front Grille Bezel for Polaris RZR 200:

The bezel is available in three colors: raw, red, and white, allowing you to customize the look of your vehicle. It fits seamlessly with the existing front clip and adds a stylish accent.

Rev_021623

RZR 200 Front Grille Bezel Kit

SKU(s): 925FP0201 (raw), 925FP0202 (red), 925FP0203 (white)

INCLUDED PARTS

(1) Grille Bezel

(1) Hardware Kit

REQUIRED TOOLS

Push Dart Tool

T-40 Socket

1/16” Allen Wrench

1/4" Socket

7/64” Drill Bit

Rev_021623

Step 1: Remove (2) push darts holding the hood center piece on. Remove (2) push darts

underneath the hood center piece.

Step 2: Remove (3) push darts on both front fenders.

Rev_021623

Step 3: Unplug both low/high beam connectors, located underneath the hood.

Step 4: Remove (4) T-40 screws holding the front clip onto the vehicle. (2) are located in the

front of the vehicle under the headlights. The other (2) are located underneath the car

where the A-arms connect to the frame. Now remove the front clip.

Rev_021623

Step 5: Bring the front clip to a work bench. Lay the grille bezel in place. With a 7/64” drill bit,

drill through each hole one by one, installing hardware after each hole is drilled.

Step 6: With a 1/16” Allen wrench and 1/4" socket, fasten down all hardware. DO not over

tighten.

Rev_021623

Step 7: Reinstall the front clip with all hardware. Don’t forget to reconnect the low/high beam

connectors.

Thank you for choosing Evolution Powersports products. If you require further assistance, please call our Tech

Support @ (715) 247-3862

Note: This product is exempt from the emission standards and related requirements of 40 C.F.R. § 1051 as provided

by 40 C.F.R. § 1051.620, and California law [e.g., vehicle code§§ 27156 and 38391]. This product is sold only for use

in connection with EPA certified, purpose-built, nonroad vehicles used solely for closed course, nonroad

competition/racing and not used for any recreational purpose or on public highways or right of ways maintained by

and open to the public. This product is sold only in connection with machines that do not fall under state and/or

federal noise or emission standards/regulations. Purchasers who/that purchase this product represent and warrant

that the product is purchased only in connection with EPA -certified, emission-regulations-exempt and noise-

regulations-exempt competition/racing vehicles as interpreted under applicable state and/or federal law. Questions:

Call Evolution Powersports at (715) 247-3862.

EVOLUTION POWERSPORTS 925FP0202 Front Grille Bezel for Polaris RZR 200 User manual

Brand: EVOLUTION POWERSPORTS

Model: 925FP0202 Front Grille Bezel for Polaris RZR 200

Type: User manual

EVOLUTION POWERSPORTS 925FP0202 Front Grille Bezel for Polaris RZR 200:

The bezel is available in three colors: raw, red, and white, allowing you to customize the look of your vehicle. It fits seamlessly with the existing front clip and adds a stylish accent.

Download PDF

report

EVOLUTION POWERSPORTS 925FP0202 Front Grille Bezel for Polaris RZR 200 User manual

EVOLUTION POWERSPORTS 925FP0202 Front Grille Bezel for Polaris RZR 200 User manual

Related papers

Other documents