EVOLUTION POWERSPORTS RZR Pro User manual

Brand
EVOLUTION POWERSPORTS
Model
RZR Pro
Type
User manual

EVOLUTION POWERSPORTS RZR Pro is a high-performance exhaust system that enhances your vehicle's power and sound. Its key features include improved airflow, reduced backpressure, and a deep, aggressive exhaust note. It is designed for closed-course, non-road racing and competition use only, offering increased performance on the track.

EVOLUTION POWERSPORTS RZR Pro is a high-performance exhaust system that enhances your vehicle's power and sound. Its key features include improved airflow, reduced backpressure, and a deep, aggressive exhaust note. It is designed for closed-course, non-road racing and competition use only, offering increased performance on the track.

Rev_071222
Polaris Pro R Magnum Header Exhaust
SKU(s):
INCLUDED PARTS
(1) EVP Header
(1) Header Gasket
REQUIRED TOOLS
10, 14mm Socket
M6 Allen Socket/Wrench
Torque Wrench
Anti-Seize
7/8 Open End Wrench
Rev_071222
Step 1: Make sure your vehicle is cold. Remove the two 14mm bolts with springs that seal the
header to the muffler.
Step 2: With the 7/8” open end wrench, remove the 02 sensor. Be sure not to damage the tip of
the sensor.
Step 3: Remove the (4) 10mm bolts holding the heat shield down.
Step 4: Remove the (9) M6 socket head cap bolts holding the header on. You can remove the
header now.
Rev_071222
Step 5: Remove the old gasket between the header and engine. Make sure to clean all the old
gasket off. You can use scotch brite and break cleaner.
Step 6: Once clean, add anti-seize to your (9) mounting bolts. Hold the gasket against the
engine block and thread in bolts #6 and #9, leaving them a 1/4" out of the block. This will
allow the EVP header to rest on them.
Rev_071222
Step 7: Install the EVP header and the rest of your mounting bolts along with the donut gasket
between the header and muffler. Torque each bolt within sequence shown below. First
torque all (9) mounting bolts to 60 in-lbs (7Nm). Second torque all (9) mounting bolts to
22 ft-lbs (30Nm)
Step 8: Torque the header pipe to muffler down to 18 ft-lbs. It helps to put anti-seize on these
on bolt threads and end of spring.
**NOTE: If you’re installing a EVP muffler please find those instructions on our webpage*
Thank you for choosing Evolution Powersports products. If you require further assistance, please call our Tech
Support @ (715) 247-3862
Note: This product is exempt from the emission standards and related requirements of 40 C.F.R. § 1051 as provided
by 40 C.F.R. § 1051.620, and California law [e.g., vehicle code§§ 27156 and 38391]. This product is sold only for use
in connection with EPA certified, purpose-built, nonroad vehicles used solely for closed course, nonroad
competition/racing and not used for any recreational purpose or on public highways or right of ways maintained by
and open to the public. This product is sold only in connection with machines that do not fall under state and/or
federal noise or emission standards/regulations. Purchasers who/that purchase this product represent and warrant
that the product is purchased only in connection with EPA -certified, emission-regulations-exempt and noise-
regulations-exempt competition/racing vehicles as interpreted under applicable state and/or federal law. Questions:
Call Evolution Powersports at (715) 247-3862.
1
9
7
3
5
8
4
2
6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

EVOLUTION POWERSPORTS RZR Pro User manual

Brand
EVOLUTION POWERSPORTS
Model
RZR Pro
Type
User manual

EVOLUTION POWERSPORTS RZR Pro is a high-performance exhaust system that enhances your vehicle's power and sound. Its key features include improved airflow, reduced backpressure, and a deep, aggressive exhaust note. It is designed for closed-course, non-road racing and competition use only, offering increased performance on the track.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents