Intelbras AMT 8000 LITE User manual

User’s Manual

AMT 8000 LITE

English

AMT 8000 LITE

Alarm center

Congratulations, you have just purchased a product with Intelbras quality and safety.

The AMT 8000 LITE wireless alarm center features advanced technology and is easy to program. All 8000

series devices can be connected, exchanging encrypted information, for increased system security. This center

has an integrated siren and 16 partitions .The system has differentials such as a high-performance wireless

device communication (bidirectional) with a range of up to 1000 meters without barriers and direct sight,

GPRS, GSM, and Ethernet type connections to provide easier monitoring reporting to 2 IPs (monitoring

companies) plus the Intelbras Cloud connection using initially the random remote access password indicated

along with the QR code label that also contains the MAC.

The AMT 8000 LITE center has remote software (rmware) updates, using Ethernet communication to down-

load the rmware version. In addition to this option, the center can also be updated using the BootLoader

resource. For this, it is necessary to have the Atualizador 8000 software previously installed on your computer.

ATTENTION: this product comes with a factory default password. For your security, it is essential that you

change it as soon as you install the product and ask your technician about the passwords set, which users

have access and the recovery methods.

Care and Safety

» Follow all instructions in the manual to install and handle the product.

» Install in environments not susceptible to factors such as rain, fog and water splashes.

» Wireless communication technology, when exposed to environments with high power radiation, may suffer interference

and and have its performance impaired. Example: locations near TV towers, AM/FM radio stations, amateur radio sta-

tions, etc.

» Do not install the alarm center and its accessories near radio frequency equipment such as routers, repeaters, and/or

Wi-Fi signal ampliers. The center and its devices must maintain a minimum distance of 2 meters from this equipment.

» Do not install the alarm center facing air conditioning equipment or heaters.

» Do not expose to direct sunlight.

» Clean only the outside of the device, using a damp cloth (do not use chemical solvents).

» Do not subject the device to excessive pressure or shock/drops.

» Check that at the installation site, the LED indicator of the devices ashes green when activated.

» Avoid installation on metallic surfaces so as not to weaken the transmission signal between the system’s devices.

» Installation and conguration of the center and of the other products that make up this system must be performed by

a qualied professional.

» Perform periodic tests on it, in order to validate weather conditions, battery level and other factors, so that the site

monitored by the system is always in proper operating conditions.

» LGPD - General Personal Data Protection Law: Intelbras does not access, transfer, collect or otherwise process any per-

sonal data from this product.

Summary

1. Technical Specications 6

2. AMT 8000 LITE Alarm Center Features 7

3. AMT 8000 LITE Accessories 7

3.1. GPRS XG 2G module and GSM XG 3G module .....................................................7

3.2. Wireless keyboard for alarm centers - XAT 8000 ....................................................8

3.3. Remote Control - XAC 8000 ..................................................................9

3.4. Wireless Siren - XSS 8000 ...................................................................10

3.5. Wireless Magnetic Sensor - XAS 8000 ..........................................................10

3.6. Wireless Passive Infrared Sensor - IVP 8000 Pet ...................................................11

3.7. Wireless Passive Infrared Sensor - IVP 8000 Pet Cam ...............................................12

3.8. Wireless Passive Infrared Sensor - IVP 8000 EX ....................................................13

3.9. Transmissor universal – TX 8000 ...............................................................14

3.10. RF Range Amplier (REP 8000 Repeater) .......................................................14

3.11. Wireless Actuator - PGM 8000 ...............................................................15

4. Installation of the center and its peripherals 16

4.1. Power supply for the alarm center (full range 90 and 265 Vac) ........................................18

4.2. Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

4.3. XG 2G/XG 3G Module ......................................................................19

4.4. AMT 8000 LITE Alarm Center .................................................................20

5. Operation 20

5.1. Description of the XAT 8000 LCD keypad instructions ...............................................20

5.2. Problems Display ..........................................................................20

5.3. Description of the LED signaling of the alarm center boards ..........................................20

5.4. Partition .................................................................................21

5.5. Activation/deactivation of the alarm center .......................................................22

5.6. Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

5.7. Remote Update ...........................................................................26

6. Programming 27

6.1. Programming mode .......................................................................27

6.2. Wireless devices (register/delete) ..............................................................29

6.3. Wireless sensor functions ....................................................................36

6.4. Remote control key functions .................................................................38

6.5. Wireless keyboard functions ..................................................................40

6.6. Siren functions ............................................................................42

6.7. Update .................................................................................49

6.8. Passwords ...............................................................................49

6.9. Quick setup for monitoring ...................................................................53

6.10. Zone settings ............................................................................56

6.11. Programming the center’s partitioning .........................................................60

6.12. Timings ................................................................................61

6.13. Alarm center time settings ..................................................................63

6.14. Timezone ..............................................................................65

6.15. Periodic test .............................................................................66

6.16. Autoactivation ...........................................................................66

6.17. Monitoring settings .......................................................................70

6.18. Activation/deactivation of functions ...........................................................84

6.19. Time to send AC failure ....................................................................87

6.20. System reset ............................................................................87

6.21. Quick programming reference ...............................................................88

6.22. Homologation ..........................................................................105

Warranty Terms 106

6

1. Technical Specications

Product Monitored alarm center

Integrated siren Audible power of 100 decibels at 1 (one) meter

AC power supply 90 to 265 V (cable gauge ≥1 mm recommended)

DC power supply 5.7 from the AMT 8000 LITE/PRO power supply

Battery Rechargeable 3.7 Vdc battery (included with the alarm center)

Operating Temperature -10 °C to 50 °C @ 90% humidity

Weight 568 grams (with battery)

Dimensions (W × H × D) Product: 84 × 290 × 273 mm

With individual packaging: 90 × 292 × 276 mm

Potência média¹

AMT 8000 LITE: 5.2 Watts

AMT 8000 LITE + XG: 8.1 Watts

Antenna type: Internal

Antenna Gain: 0 dBi

Wireless communication frequency

AMT 8000 LITE/Accessories 915 to 928 MHz via internal antenna, power 18 dBm

Modulation DSSS BPSK 40 Kbps

Battery Internal, 3.7 Vdc rechargeable lithium

Optional²

XAC 8000 Remote Control

REP 8000 RF Range Amplier

Wireless keyboard XAT 8000

XAS 8000 Wireless magnetic sensor

TX 8000 Universal transmitter

Wireless passive infrared sensor IVP 8000 EX

Wireless passive infrared sensor IVP 8000 Pet

Wireless passive infrared sensor IVP 8000 Pet Cam

GPRS XG 2G Module

GSM XG 3G Module

Wireless Siren XSS 8000

Wireless Actuator PGM 8000

1

Requirements: maximum power veried with the alarm center activated, with registered peripherals (keyboards/sensors/sirens), and with the

communication means connected and operating together with the center. In some operations, the consumption can vary according to the number of

peripherals operating in the security system and their information exchange (Stand by mode - continuous).

² Optional:

for more information see

www.intelbras.com.br

.

Attention: Intelbras wireless systems are tested to the highest standards and bring high reliability, however, due to the use/installa-

tion in varied scenarios, some considerations must be taken into account

:

» The transmitters/receivers may be disturbed by radio signals, natural interferences, the device’s operating location, wea-

ther conditions and other adversities that affect data transmission regardless of the frequency or technology used, since

the transmission medium is adverse and different from place to place.

» The devices’ receivers/transmitters have an internal processing time, and only receive the data needed for communication

between them after this particular time for the system.

» Wireless devices should be tested regularly to determine if there are sources of interference and to protect against

possible failures.

7

2. AMT 8000 LITE Alarm Center Features

» Capacity for 16 partitions with independent activation/deactivation.

» Zone allocation according to the desired partitions.

» Wireless signal receiver/transmitter integrated into the alarm center operating at a frequency of 915 to 928 MHz.

» Support 2 cellular chips (SIM card) with XG 2G or XG 3G module installed.

» GPRS quad-band modem: compatible with most national GSM operators for the AMT 8000 LITE operating with the XG 2G

and XG 3G module (sold separately).

» Event reporting by Ethernet connection, GPRS connection (with the XG 2G module installed - sold separately) and GSM

connection (with the XG 3G module installed - sold separately).

» Remote access of the alarm center via application.

» Used together with all wireless devices in the 8000 line.

» Capacity of visualization and programming of parameters by up to 16 XAT 8000 keyboards.

» Integrated wired siren plus 16 wireless sirens XSS 8000.

» Integrated wired siren plus 16 wireless sirens XSS 8000

» Remote programming via Ethernet, GPRS and GSM.

» Capacity for connecting up to 04 REP 8000 RF ampliers.

» Programming for up to 97 passwords including duress with congurable permissions.

» Monitorable by the Contact-ID protocol.

» Supervision of sensors, wireless sirens, keyboards, PGMs, and repeaters.

» Low battery detection of wireless devices.

» Internal buffer for 512 events.

» Remote software update through Ethernet connection.

3. AMT 8000 LITE Accessories

The AMT 8000 LITE alarm center can have several accessories grouped together to compose the monitoring and security

system. The accessories are responsible for communication and monitoring, the buzzer, the LCD keyboard, and several

sensors, for the best adequacy and composition of the necessary protection system.

3.1. GPRS XG 2G module and GSM XG 3G module

Optional dedicated accessory for data transmission via GPRS / GSM for communication, conguration and event reporting

between user and/or monitoring company with the AMT 8000 LITE security system.

Features

» Supports up to two SIM card type chips.

» GPRS communication in 2G with XG 2G module and 2G/3G communication with XG 3G module.

» External antenna with 0 dB gain.

» Reports events to 2 IP destinations (monitoring company) plus the Intelbras cloud.

» Connections to DNS destinations.

» Power supply from the AMT 8000 LITE alarm center.

8

The following picture shows an illustrative image of the XG 2G and XG 3G modules:

ST

100

25V

GPRS XG 2G and GSM XG 3G Module

Note: XG 2G and XG 3G modules are compatible with most of the national GPRS / GSM operators with 2G and 3G

technology.

3.2. Wireless keyboard for alarm centers - XAT 8000

Optional dedicated accessory for conguring, checking status, and operating the AMT 8000 LITE alarm center. The commu-

nication between the keyboard and the alarm center is carried out via a wireless signal, providing a simpler installation and

with a longer communication range. Up to 16 XAT 8000 keyboards can be added to each alarm center.

Features

» 3-line monochrome character liquid crystal display:

» 1st line for graphic icons (alarm center battery charge indication, trouble indication, and activated siren).

» 2nd message line with 14 segments.

» 3rd message line with 14 segments.

» Keyboard with illuminated keys.

» Cover to protect against accidental actuation of the keys.

» Brightness sensor for activating the display and key illumination.

» Problem Viewing.

» Wireless communication with the alarm center (915 to 928 MHz) through an internal antenna, power 11 dBm.

» Simplies alarm center programming.

» Text message viewing.

» Center’s battery level display.

» Zone status display (open/closed).

» Partition status signaling.

» Panic, Medical emergency and Fire function.

» Audible Signaling during operation.

» DC power supply: 4 batteries 3 Vdc (CR2450) included.

» Communication supervision and encrypted transmission.

» Range: up to 1000 meters with direct line of sight in open eld.

9

The following gure shows an illustrative image of the keyboard:

1 2 3

4 5 6

7 8

0

9

Wireless Keyboard XAT 8000

The keyboard has a tamper switch, located on its front side, under the cover, and activated by moving the keyboard cover,

its function is to activate the keyboard. On the front of the XAT 8000 there is also a light guide for the brightness sensor,

whose function is to control the brightness intensity of the display and keyboard for battery optimization.

The keyboard installation can be done on several surfaces, always placing it in a vertical position in relation to the oor and

using double-sided tape or screws (not included) to x the base, and after attaching the device, tting and checking if it

was placed correctly to avoid falls and damages.

3.3. Remote Control - XAC 8000

Optional dedicated accessory for interface between user and alarm center. It allows activating, deactivating and performing

other functions together with the alarm center with three keys and luminous identication of the events. Up to 98 XAC

8000 controls can be added to each alarm center.

Features

» Visual indication of communication with the system through a bicolor LED.

» 3 programmable buttons.

» Wireless communication with the alarm center (915 to 928 MHz) through an internal antenna.

» Power 11 dBm.

» DC power supply: 1 long-life internal 3 Vdc battery (CR2032).

» Encrypted transmission.

» Range: up to 200 meters with direct line of sight in open eld.

The following gure shows an illustrative image of the control:

XAC 8000 Remote Control

10

3.4. Wireless Siren - XSS 8000

Optional dedicated accessory for audible status warning, intrusion and emergency indications from the AMT 8000 LITE

alarm center. Communication between the siren and the alarm center is done through a wireless signal, providing a

simpler installation with a long communication range. Up to 16 XSS 8000 sirens can be added to each AMT 8000 LITE

alarm center.

Features

» Sound power of 100 dB at 1 meter.

» Communication status checking via LED.

» Audible trigger if communication with the alarm center is lost.

» Wireless communication with the alarm center (915 to 928 MHz) through an internal antenna, power 11 dBm.

» DC Power supply: 1 non-rechargeable Li-SoCl2 3.6 V / 14 A battery with wire/connector - included.

» Communication supervision and encrypted transmission.

» Range: up to 1000 meters with direct line of sight in open eld.

The following gure shows an illustrative image of the siren:

Wireless siren XSS 8000

The XSS 8000 has a tamper switch, located on the back of the siren, and if this key is opened/violated, registered sirens will trip

and send the corresponding event if the Triggering Problems is enabled (see section

Triggering Problems

).

The installation of the siren can be on various surfaces, always placing it in a vertical position with a height between 1.80

and 2.20 meters from the oor and using double-sided tape or screws (not included) to x the base and after attaching the

device, tting and checking for correct placement to avoid falls and damage. The communication status between the siren

and the alarm center will be represented by the LED indicator located on the front panel, and when in normal communi-

cation the LED will blink green, with partial communication it will blink orange and without communication, it will blink

red (the LED indicator after 15 minutes will go into hibernation mode for battery saving, not harming the communication

of the device and to activate it again press once the synchronization key of the device).

3.5. Wireless Magnetic Sensor - XAS 8000

Optional dedicated accessory for door and window opening verication with a differentiated, discreet and compact design.

With low battery indication and communication status in the sensor, supervision, activation and anti-tamper system with

internal tamper to compose the security system line 8000 with maximum results.

Features

» Wireless communication with the alarm center (915 to 928 MHz) through an internal antenna, power 11 dBm.

» Communication status check via LED.

» Fixing by screws (not included) or double-sided tape (not included).

» DC power supply: 1 x 3 Vdc long-life CR2450 lithium battery.

» Communication supervision and encrypted transmission.

» Range: up to 1000 meters with direct line of sight in open eld.

11

The following gure shows an illustrative image of the XAS 8000 sensor:

Opening sensor XAS 8000

The XAS 8000 sensor has a tamper switch, and if this tamper switch is opened/violated, registered sirens will trip and

send the corresponding event if the

Triggering Problems

function is enabled (see section

Triggering Problems

). The status

of the communication between the sensor and the alarm center will be represented by the LED indicator located on the

front. When in normal communication the LED will blink green, with partial communication it will blink orange and without

communication it will blink red (the LED indicator after 15 minutes will go into hibernation mode to save battery power,

not harming the communication of the device and to activate it again, press once the synchronization key of the device).

3.6. Wireless Passive Infrared Sensor - IVP 8000 Pet

Dedicated accessory for verifying intrusions by means of infrared reading in indoor environments, in a discreet and compact

way, taking into account the presence of pets and not triggering the alarm. With low battery indication and communication

status in the sensor, supervision, activation, and anti-tamper system with internal tamper to compose the 8000 line security

system with the best results.

Features

» Wireless communication with the alarm center (915 to 928 MHz) through an internal antenna, power 11 dBm.

» Communication status check via LED.

» 12-meter by 90° coverage.

»

Pet

function with detection ≥20 kg.

» Fixation by screws (not included) or double-sided tape (not included).

» DC power supply: 1 x 3 Vdc long-life CR123A lithium battery.

» Communication supervision and encrypted transmission.

» Range: up to 1000 meters with direct line of sight in open eld.

» Delay of up to 2 minutes for detection of activated centers.

The following gure shows an illustrative image of the IVP 8000 Pet sensor:

Presence Sensor IVP 8000 Pet

12

The IVP 8000 Pet sensor has a tamper switch, and if this tamper switch is opened/violated, the registered sirens will trip and

send the corresponding event if the

Triggering Problems

function is enabled (see section

Triggering Problems

). The status of

the communication between the sensor and the alarm center will be represented by the LED indicator located on the front

panel. When in normal communication the LED will blink green, with partial communication it will blink orange, and with no

communication it will blink red (the LED indicator after 15 minutes will go into hibernation mode to save battery power, not

affecting the device’s communication, to activate it again, press the device’s synchronization key once).

3.7. Wireless Passive Infrared Sensor - IVP 8000 Pet Cam

Dedicated accessory for verifying intrusions by means of infrared reading in indoor environments, in a discreet and compact

way, considering the presence of pets and not triggering the alarm. It has a camera that, after the sensor is triggered,

sends the image of the location to applications and software compatible with the AMT 8000 LITE center. With low battery

indication and communication status in the sensor, supervision, activation, and anti-tamper system with internal tamper to

compose the 8000 line security system with the best results.

Features:

» Wireless communication with the alarm center (915 to 928 MHz) through an internal antenna, power 11 dBm.

» Communication status checking via LED.

» 12-meter by 90° coverage.

» Pet function with detection ≥20 kg.

» It takes two pictures per trip. Therefore, it covers both bright and dark/nighttime environments.

» Fixation by screws (not included) or double-sided tape (not included).

» DC power supply: 2 3 Vdc long-life CR123A lithium batteries.

» Communication supervision and encrypted transmission.

» Range: up to 1000 meters with direct line of sight in open eld.

» Delay of up to 2 minutes for detection of activated center.

The following gure shows an illustrative image of the IVP 8000 Pet Cam sensor:

Presence Sensor with IVP 8000 Pet Cam

The IVP 8000 Pet Cam sensor has a tamper switch, and if this tamper switch is opened/violated, the registered sirens will trip

and send the corresponding event if the

Triggering Problems

function is enabled (see section

Triggering Problems

). The status

of the communication between the sensor and the alarm center will be represented by the LED indicator located on the front

panel. When in normal communication the LED will blink green, with partial communication it will blink orange, and with no

communication it will blink red (the LED indicator after 15 minutes will go into hibernation mode to save battery power, not

affecting the device’s communication, to activate it again, press the device’s synchronization key once). The center can store up

to 126 trigger events with photos (two photos per trigger), so up to 126 trigger events with photos can be viewed, as long as

the event buffer has not been subscribed to the center’s memory by other events.

13

3.8. Wireless Passive Infrared Sensor - IVP 8000 EX

Dedicated accessory for checking intrusions through infrared reading in outdoor environments, in a discreet and compact way

and taking into account the presence of pets and not triggering the alarm. With low battery indication and communication

status in the sensor, supervision, activation, and anti-tamper system with internal tamper to compose the security system 8000

line with the best results.

Features:

» Water protection and IPX4;

» Antisabotage;

» Communication status checking via LED;

» Wireless communication with a range of up to 1000 meters with direct open eld of view;

» Supervised Wireless Communication;

» Encrypted transmission;

» Micro-controlled sensor;

» Sensor Operation Setting via AMT Remoto Mobile Application;

» Pet Immunity up to 30 Kg;

» White light immunity up to 20,000 lux;

» High RFI/EMI immunity;

» Tamper-proof key for front cover and base of the product;

» Easy to install.

The following gure shows an illustrative image of the IVP 8000 EX sensor:

Presence Sensor IVP 8000 EX

The IVP 8000 EX sensor has a tamper switch, and if this tamper switch is opened/violated, the registered sirens will trip and

send the corresponding event if the

Triggering Problems

function is enabled (see section

Triggering Problems

). The status of

the communication between the sensor and the alarm center will be represented by the LED indicator located on the front

part. When in normal communication the LED will blink green, with partial communication it will blink orange, and with no

communication it will blink red (the LED indicator after 15 minutes will go into hibernation mode to save battery power, not

affecting the device’s communication, to activate it again, press the device’s synchronization key once).

14

3.9. Transmissor universal – TX 8000

Optional accessory dedicated to receive signals from wired sensors and transmission of this reading to the AMT 8000 LITE

alarm center. The operation of this device is the same as that of a wireless magnetic sensor XAS 8000, but its activation

will occur every time another sensor has an opening/closing and sends a signal via a pair of wires of the dry contact type

(NO or NC), thus transforming a wired sensor into a wireless one.

Features:

» Wireless communication with the alarm center (915 to 928 MHz) through an internal antenna, power 11 dBm.

» Communication status checking via LED.

» Fixation by screws (not included) or double-sided tape (not included).

» DC power supply: 1 x 3 Vdc long-life CR2450 lithium battery.

» Communication supervision and encrypted transmission.

» Range: up to 1000 meters with direct line of sight in open eld.

The following gure shows an illustrative image of the TX 8000 transmitter:

Transmitter for wired sensors TX 8000

The TX 8000 Transmitter has a tamper switch, and if this tamper switch is opened/violated, the registered sirens will trip and

send the corresponding event if the Triggering Problems fun

ction is enabled (see sectio

n Triggering Problems). The status of

the communication between the sensor and the alarm center will be represented by the LED indicator located on the front

panel. When in normal communication the LED will blink green, with partial communication it will blink orange, and with no

communication it will blink red (the LED indicator after 15 minutes will go into hibernation mode to save battery power, not

affecting the device’s communication, to activate it again, press the device’s synchronization key once).

Attention: the installation of the sensors can be done on several surfaces, always respecting the best position and height

for the sensor to read the data correctly. Use double-sided tape or screws (not included) to x the base, and then attach the

device, tting and checking for correct placement to avoid falls and damage. Observe the maximum distance of communi-

cation between the devices and the alarm center.

3.10. RF Range Amplier (REP 8000 Repeater)

Optional dedicated accessory for amplifying the RF range between the AMT 8000 LITE center and other devices. The

communication between the repeater and the alarm center is done through a wireless signal, providing a simpler installa-

tion and a long communication range. The repeater can be installed at a distance of 1000 meters from the center without

barriers and the other devices at 1000 meters from the repeater, also without barriers. Extending the range of the center

from 1000 m to 2000 m barrier-free.

Features:

» Range: up to 1000 meters with direct line of sight in open eld.

» AMT 8000 LITE system coverage area amplier.

» Protection against malicious signals.

» Encrypting data transmission between devices.

» Easy installation and handling.

» Amplication of the RF signal up to 1000 meters beyond the maximum limit for communication with the center, so with

the use of the amplier a device can communicate at a distance of up to 1.2 kilometers with the alarm center when it is

in direct line of sight and without barriers.

» Rechargeable battery.

» 7 Vdc/500 mA power supply included.

15

Important: each AMT 8000 LITE alarm center can have up to 4 repeaters operating simultaneously, but all operating

separately from each other, so there is no possibility of a repeater being used to extend the signal to another repeater, only

in direct use between devices and the alarm center.

The following gure shows an illustrative image of the repeater:

RF range amplier (REP 8000 repeater)

The RF Range Amplier (REP 8000 Repeater) has a tamper key located on the back of it, and if this key is opened/violated,

registered sirens will trip and send the corresponding event if the

Triggering problems

function is enabled (see section

Triggering Problems

).

The installation of the RF Range Amplier (REP 8000 repeater) can be on various surfaces, always placing it in a vertical

position with a height between 1.80 and 2.20 meters from the oor and using double-sided tape or screws (not included)

to secure the base and after attaching the device, tting and checking for correct placement to avoid falls and damage.

The status of the repeater’s communication with the alarm center will be represented by the LED indicator located on the

front side, which will blink green when the communication is normal, orange when there is partial communication, and red

when there is no communication (the LED indicator will go into hibernation mode after 15 minutes to save battery power,

not affecting the device’s communication, to activate it again press once the device’s synchronization key).

3.11. Wireless Actuator - PGM 8000

Optional accessory dedicated to driving electrical devices such as gates, spotlights, electronic locks, etc. The communication

between the PGM actuator and the center is done through a wireless signal, providing a simpler installation and a long

communication range. Up to 16 PGM 8000 Actuators can be added.

Features:

» Communication status checking via LED.

» Wireless communication with the alarm center (915 to 928 MHz) through an internal antenna, power 11 dBm.

» DC Power: 1 non-rechargeable battery 3V CR2032 - included.

» DC power supply: 12 Vdc to 24 Vdc - not included.

» AC Power Supply: 110/220 Vac.

» Communication supervision and encrypted transmission.

» Protection against malicious signals.

» Range of up to 1000 meters with direct line of sight in open eld.

» Easy installation and handling.

16

The following gure shows an illustrative image of PGM:

Wireless actuator (PGM 8000)

The PGM 8000 has a tamper switch, located on its back, and if this switch is opened/violated, registered sirens will trip and

send the corresponding event if the

Triggering Trouble

function is enabled (see section

Triggering Trouble

).

The PGM can be installed on various surfaces, always placing it in a vertical position using double-sided tape or screws

(not included) to x the base and then attach the device. The communication status of the PGM with the alarm center will

be represented in it through the LED indicator located on the front, and when in normal communication the LED will ash

green, with partial communication in orange and without communication in red. In case of power failure, the PGM will

run on battery power which will report the AC Failure events and maintain the PGM supervision test with the alarm center.

Note:

in case of PGM power loss the output will return with the contact in the same state as it was before the loss.

4. Installation of the center and its peripherals

Attention: only connect the center to the mains and battery after the installation of all equipment and peripherals

.

Open the product’s box and then open the cover of the alarm center´s cabinet removing the screws, where you will be able

to see two boards, that is, its basic conguration contains the board of the AMT 8000 LITE alarm center and its respective

power supply and the rechargeable battery that comes with the center.

The modules XG 2G and XG 3G can be acquired, and these boards have their respective interconnection cables with

the center.

The AMT 8000 LITE alarm center only has wireless zones, as the other accessories (keypad, sirens, etc.) are connected to

the alarm center via wireless signal, with only the AC power and Ethernet network cables connected to the alarm center.

17

The following image illustrates the center with all the devices that can be physically connected:

1 3

4

2

5

6

7

8

AMT 8000 LITE/PRO

Alarm center AMT 8000 LITE

1. Opening for the network cable (Ethernet).

2. Integrated siren connection.

3. Connector for Ethernet network cable.

4. Key for registering wireless devices.

5. Input for at power supply cable.

6. Micro-USB type connector for updating the alarm center’s rmware.

7. Connector for at cable of the XG 2G / XG 3G modules.

8. Connector for SIM card 1 and SIM card 2.

9. Input connector for the two-way battery cable.

18

1

3

2

27

1. Tamper-proof switch.

2. Integrated siren.

3. AC power connector.

Attention: The AMT 8000 LITE alarm center does not have an auxiliary output to power other devices and you should not use

any connection point on the boards of the center and its accessories for this function, because besides damaging the center, you

can damage the devices because the center operates with different voltages depending on the circuit

.

4.1. Power supply for the alarm center (full range 90 and 265 Vac)

The alarm center is equipped with a full-range switched power supply that works with an input voltage of 90 and 265 VAC

without needing a voltage selector switch. This way, even if some voltage variation occurs in the electrical grid, the alarm

center will continue working normally (as long as the voltage is in the 90 to 265 Vac range).

On this board there are two fuses that protect the center. If you need to change them, use new ones of the same

value (250 V/400 mA).

For connecting the AC mains input and also for grounding, it is recommended to use a three-pin cable with a gauge of 1 mm or higher.

The output to the alarm center board is 5.7 Vdc and 1.7 A.

AC AC

Power Supply AMT 8000 LITE/PRO

19

Connect the ground terminal of the power supply as shown above to the local electrical ground.

If the local electrical installation does not have a grounding system, install a grounding bar and connect the connection

terminal to the center in order to perform the correct grounding.

Attention: it is mandatory to connect the grounding to the center so that there is better protection against lightning

and overloads by the power grid. If this connection is not made, the center will work normally but will be unprotected

against overloads

.

The warranty does not cover possible lightning damage to the center or to any other equipment connected to it.

4.2. Battery

The AMT 8000 LITE alarm center has an internal 3.7 Vdc rechargeable battery with a capacity of 2,000 mA. The battery

connector is located on the power supply board and is used to connect the battery to the alarm system. To connect the

battery to this connector use the cable that comes connected with it, as shown in the following gure.

AC AC

Rechargeable battery for AMT 8000 LITE alarm center

The alarm center has protection against reverse polarity and short circuits in the battery and protection to prevent the

battery from being damaged in case of a mains failure (if the battery voltage is below 2.8 V the alarm center will turn off

to avoid damaging the battery).

Attention: the battery can take up to 12 hours to complete its rst charge cycle.

Duração da bateria:

» Approximately 4 hours reporting of events via GPRS/Ethernet + integrated siren constantly triggering;

» Approximately 13 hours reporting events via GPRS (hourly periodic test only and with integrated siren in standby);

» Approximately 17 hours reporting events via ETH (only periodic hourly test and with integrated siren in stand by).

Attention: if battery replacement is required, look for our network of authorized technical assistance.

4.3. XG 2G/XG 3G Module

Its installation must only be done with the center turned off, to avoid damage to the equipment and to the installer.

In the XG 2G/XG 3G modules there are two slots to be allocated two chips (SIM card) being superimposed one over the

other, with chip 1 being above chip 2. When installing the chips, leave the metallic contacts facing down and insert them

until the end of the slot for the correct allocation of the chips.

2

1

CHIP

CHIP 1CHIP 2

Chip Allocation in the Module

20

4.4. AMT 8000 LITE Alarm Center

The AMT 8000 LITE alarm center has a built-in wired siren, and a tamper-proof switch, and if the tamper is opened/violated,

the built-in siren plus the registered sirens will trip and send the corresponding event if the Triggering Problems function is

enabled (see section Triggering Problems).

The Ethernet and AC power cables must be routed through the hole located at the back of the panel.

The installation of the center can be done on several surfaces, always placing it in a vertical position with a height between

1.80 and 2.20 meters and using double-sided tape or screws (not included) to x the base and after fastening the center,

tting and checking if it has been properly placed to avoid falls and damage and guiding the wires in the dedicated areas.

5. Operation

Once the installation is complete, turn on the center by connecting it to the local power grid and to the rechargeable

battery.

Note:

to turn on the AMT 8000 LITE alarm center it must be connected to the AC mains and the 5-wire cable from the

power supply must be connected to the Power Supply connector on the alarm center board, otherwise, the center will not

turn on even if the power supply is on battery. With the center on and the battery connected, it will be recharged by the

power supply and when the AC power fails, the center will be maintained by battery power.

5.1. Description of the XAT 8000 LCD keypad instructions

In the upper part of the LCD display are located the indication icons described below:

» : if this icon is blinking, it indicates that a problem has been detected.

» : will light up whenever the siren is triggered

.

» P: with the icon lit, the center is in programming mode.

» Battery: indicates the state of the alarm center’s battery.

5.2. Problems Display

The occurrence of problems is described as follows:

On the XAT 8000 keyboard the icon will be ashing.

If any problems are detected, press the up or down arrow keys on the XAT 8000 keypad to view them. To end the viewing,

press the

Exit

key.

Note:

»

If the function Indication of problems by siren on activation/deactivation and Siren beep on activation/deactivation is

enabled and if a problem is detected, 1 long beep will be emitted on activation and 2 long beeps on deactivation.

»

To clear the keyboard after triggers, simply press the Exit key

.

5.3. Description of the LED signaling of the alarm center boards

LEDs on the center’s base board

LED Status/Event Signaling1

LED1/LED2 Disconnected from Ethernet LED off

LED1/LED2 Connected to the Ethernet 1LED ashing constantly

LED3 Alarm Center Off LED off

LED3 Alarm Center On LED ashing

LED3 Alarm Center On and registering devices LED on

1

This status does not mean that the system is connected to the monitoring servers. To view the connection status, look through the Menu function

(see Connections section)

.

Page is loading ...

Intelbras AMT 8000 LITE User manual

Related papers

Other documents