Intelbras 8000 Slim System User guide

Installation/user guide

AMT 8000 Slim

Wireless theft alarm system

Congratulations, you have just purchased a product with Intelbras quality and safety.

The AMT 8000 SLIM alarm system is a solution against intrusion. Composed by the AMT 8000 alarm panel,

XSS 8000 siren, XAC 8000 remote control, IVP 8000 PET motion sensor and XAS 8000 aperture sensor, offers

protection with maximum security. With long-range fully wireless communication, it is not necessary to change

the structure of the residence for installation.

Summary

AMT 8000 - Alarm center 6

1. Technical Specications 8

2. AMT 8000 Alarm Center Features 8

3. AMT 8000 Accessories 9

3.1. GPRS XAG 8000 Module and GSM XAG 8000 3G Module ............................................9

3.2. Communication module via telephone line - FXO 8000 .............................................10

3.3. Wireless keyboard for alarm centers– XAT 8000 ..................................................10

3.4. XAC 8000 remote control ...................................................................11

3.5. Wireless siren - XSS 8000 ...................................................................12

3.6. Wireless magnetic sensor - XAS 8000 ..........................................................12

3.7. Passive infrared wireless sensor - IVP 8000 Pet ....................................................13

3.8. Passive infrared wireless sensor - IVP 8000 Pet Cam ................................................14

3.9. Universal Transmitter – TX 8000 ...............................................................14

4. Installation of the alarm center and its peripherals 16

4.1. Power supply for the alarm center (full range 90 and 265 Vac) ........................................18

4.2. Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

4.3. XAG 8000 GPRS Module ....................................................................19

4.4. FXO 8000 Phone Module ....................................................................19

4.5. AMT 8000 Alarm Center ....................................................................19

5. Operation 20

5.1. Description of the XAT 8000 LCD keyboard indications ..............................................20

5.2. Display of troubles ........................................................................20

5.3. Description of the LEDs signaling on the alarm center boards .........................................20

5.4. Partitioning ..............................................................................21

5.5. Activation/deactivation of the alarm center .......................................................21

5.6. Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

5.7. Remote update ...........................................................................26

6. Programming 26

6.1. Programming mode .......................................................................26

6.2. Wireless devices (register/delete) ..............................................................28

6.3. Wireless sensor functions ....................................................................33

6.4. Functions of Remote Control Keys .............................................................34

6.5. Functions of Wireless Keyboard ...............................................................36

6.6. Siren functions ............................................................................38

6.7. Update .................................................................................40

6.8. Passwords ...............................................................................40

6.9. Quick setup for SMS monitoring and programming .................................................44

6.10. Zone settings ............................................................................48

6.11. Programming the alarm center partitioning ......................................................51

6.12. Timings ................................................................................52

6.13. Alarm Center Time Settings .................................................................53

6.14. Periodic Test .............................................................................55

6.15. Autoactivation ...........................................................................56

6.16. Telephony and Monitoring Settings ............................................................59

6.17. Functions via SMS ........................................................................76

6.18. Activation/deactivation of Functions ..........................................................79

6.19. Time to send the AC fault ...................................................................82

6.20. System Reset ...........................................................................83

6.21. Quick programming reference ...............................................................83

XSS 8000 - Wireless siren 98

Care and security 99

1. Technical specications 100

2. Features 100

3. Initial battery activation 100

4. Register 101

5. Installation 102

6. Operation 102

7. Battery 102

8. Homologation 103

XAS 8000 - Magnetic sensor 104

1. Care and security 105

1. Technical specications 106

2. Features 106

3. Product 106

4. Installation 107

5. Identifying the best place for installation 107

6. Fixing the XAS 8000 sensor 108

7. Conguring the LED through the center unit keyboard 108

7.1. Information on LED operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108

7.2. Conguring the LED through the application ....................................................108

8. Battery 110

9. Homologation 110

IVP 8000 PET - Infrared passive sensor 111

1. Care and security 112

1.1. Scan (upper view) ........................................................................113

1.2. Detection range (side view) .................................................................113

1. Technical specications 114

2. Features 114

3. Product 115

4. Registering the IVP 8000 PET sensor 115

4.1. Deleting the sensor register .................................................................115

5. Identicando o melhor local para a instalação 116

6. Installation 116

7. Conguring the IVP 8000 PET sensor 117

7.1. Conguring the sensor through the keyboard ....................................................117

7.2. Information on sensor settings ...............................................................117

7.3. Conguring the sensor through the application ..................................................118

8. Battery 119

9. Homologation 119

XAC 8000 - Remote control 120

1. Care and security 121

1. Technical specications 122

2. Features 122

3. Register 123

4. Handling 123

5. Battery 124

6. Homologation 124

Warranty term 125

AMT 8000

Alarm center

AMT 8000 Wireless Alarm Center has advanced technology and is easy to program. Due to its differentiated technology, the

following unique wireless devices can be connected to this center: XAC 8000 remote control, XAS 8000 magnetic wireless

sensor, IVP 8000 Pet passive wireless sensor, IVP 8000 Pet Cam passive wireless sensor, XSS 8000 wireless siren, wireless

keypad for XAT 8000 alarm center, REP 8000 range RF amplier and also the TX 8000 universal transmitter with all devices

exchanging information with encryption, for greater system security. In addition to various security devices such as tamper

against removal of the installation surface and violation of devices and with long battery life. This center has 16 partitions,

8 memories for phone numbers,

Panic

function,

Emergency

function, smart battery charger with protection against short

circuit or polarity reversal, timing and sensor test function. The system has differentials such as high performance wireless

device communication (bidirectional) with a range of up to 1000 meters without barriers and direct view, GPRS and

GSM type connections, telephone line, Ethernet and Wi-Fi connection to provide greater ease for system monitoring and

checking. Reports events to 2 IP destinations (monitoring companies). The center is already directed to the Intelbras Cloud

using initially the random remote access password indicated along with the QR Code label that also contains the MAC.

AMT 8000 Center has remote software update (rmware), using Ethernet cable or Wi-Fi communication to download the

most updated rmware version.

In addition to this option, the center can also be updated using the BootLoader feature. To do this, you need to have the

Atualizador 8000

software previously installed on your computer.

Care and security

» Follow all instructions in the manual for product installation and handling.

» Perform the installation in environments not susceptible to factors such as rain, fog and splashes of water.

» Wireless communication technology, when exposed to environments with high power radiation, may suffer interference

and have its performance impaired. Example: places near TV towers, AM/FM radio stations, amateur radio stations, etc.

» Do not install the control panel and its accessories near radio frequency equipment such as routers, repeaters and / or wi-

 signal ampliers. The control panel and its devices must maintain a minimum distance of 2 meters from this equipment.

» Do not install the alarm center facing air conditioning or heating equipment.

» Do not expose directly to sunlight.

» Clean only the external part of the device, using only a damp cloth (do not use chemical solvents).

» Do not subject the device to excessive pressure or knocks/falls.

» Do not cover the device with adhesives, paper or inks.

» Check that at the installation site, the LED indicating the devices ash green when activated.

» Avoid installation on metal surfaces in order not to attenuate the transmission signal between the devices in the system.

» The installation, conguration of the center and the other products that make up this system must be performed by a

qualied professional.

» Perform periodic tests on it in order to validate weather conditions, battery level and other factors, so that the site super-

vised by the system is always able to operate correctly.

» LGPD - General Law for the Protection of Personal Data: this product handles personal data, but Intelbras does not

» has access to data from this product.

8

1. Technical Specications

Product Monitored alarm center

AC power 90 to 265 V (we recommend the use of a cable with gauge ≥ 1 mm)

DC power 5.7 V coming from XFT 8000 source

Battery 3.7 Vdc rechargeable battery (supplied with alarm center)

Operating temperature –10 °C to 50 °C @ 90% humidity

Weight 568 grams (with battery and other accessories connected - XAG and FXO)

Dimensions (W × H × D) of Product: 84 × 290 × 273 mm

With individual packaging: 90 × 292 × 276 mm

Average power¹

AMT 8000: 5.2 Watts

AMT 8000 + FXO 8000: 5.8 Watts

AMT 8000 + XAG 8000: 8.1 Watts

AMT 8000 + FXO 8000 + XAG 8000: 8.2 Watts

Antenna type: internal

Antenna gain: 0 dBi

Wireless communication frequency

AMT 8000/Accessories 915 to 928 MHz via internal antenna, power 18 dBm

Modulation DSSS BPSK 40 Kbps

Battery 3.7 Vdc lithium rechargeable, internal

Optional²

XAC 8000 remote control

REP 8000 Range RF Amplier

XAT 8000 Wireless Keyboard

XAS 8000 Wireless Magnetic Sensor

TX 8000 Universal Transmitter

IVP 8000 Pet passive infrared wireless sensor

IVP 8000 Pet Cam passive infrared wireless sensor

FXO 8000 Telephone Line Module

XAG 8000 GPRS Module

XSS 8000 Wireless Siren

XAG 8000 3G GSM Module

1

Conditions: maximum power veried with alarm center activated, with registered peripherals (keyboards/sensors/sirens) and with the

means of communication connected and operating in conjunction with the center. In some operations the consumption may vary ac-

cording to the number of peripherals operating in the security system and their information exchange (

Stand by

- continuous mode).

² Optional: for more information see the website

www.intelbras.com.br.

Attention: Intelbras wireless systems are tested to the highest standards and bring high reliability, however, due to their

use/installation in various scenarios, some considerations must be taken into account:

» Transmitters/receivers may be being disturbed by radio signals, natural interference, location of device operation, climatic

issues and other adversities that affect the transmission of data regardless of the frequency or technology used, since the

means of transmission is adverse and different from place to place.

» Receivers/transmitters of the devices have an internal processing time, and only receive the data necessary for commu-

nication between them after this particular time for the system.

» Wireless devices must be tested regularly to determine if sources of interference exist and to protect against possible

failures.

2. AMT 8000 Alarm Center Features

» Capacity for 16 partitions with independent activations/deactivations.

» Zone allocation according to the desired partitions.

» Wireless signal receiver/transmitter integrated into the alarm center operating with a frequency from 915 to 928 MHz.

» Support for 2 (SIM card) mobile phone chips with XAG 8000 module installed.

» Quad-band GPRS modem: compatible with most national GSM operators for AMT 8000 operating with XAG 8000 and

XAG 8000 3G module (sold separately).

» Event reporting via Ethernet / Wi-Fi connection, telephone line (with FXO 8000 module installed - sold separately), GPRS connection

(with XAG 8000 module installed - sold separately) and GSM connection (with XAG 8000 3G module installed - sold separately).

9

» Remote access from the alarm center via applications and services (telephone and SMS - requires communication mo-

dules).

» Use in connection with all wireless devices on the 8000 line.

» Ability to display and program parameters by up to 16 XAT 8000 keyboards.

» Ability to connect up to 16 XSS 8000 wireless sirens.

» Ability to connect up to 98 XAC 8000 controls with user identication.

» Ability to connect up to 64 wireless sensors of the 8000 line.

» Remote programming via fax/modem card, Ethernet, Wi-Fi, GPRS and GSM.

» Ability to connect up to 04 REP 8000 RF ampliers.

» Programming for up to 97 passwords including duress with congurable permissions.

» Monitorable by Contact-ID protocol.

» Supervision of sensors, sirens and keyboards.

» Low battery detection of registered wireless devices.

» Internal buffer for 512 events.

» Remote software update through Ethernet or Wi-Fi connections.

3. AMT 8000 Accessories

AMT 8000 alarm center can have several accessories grouped to compose the monitoring and security system, with the

accessories responsible for communication and monitoring, sound warning, LCD keyboard and several sensors, for better

adequacy and composition of the necessary protection system.

3.1. GPRS XAG 8000 Module and GSM XAG 8000 3G Module

Optional accessory dedicated for data transmission via GPRS / GSM for communication, conguration and reporting of

events between user and / or monitoring company with the AMT 8000 security system.

Features

» Supports up to two SIM card type chips.

» 2G GPRS communication with the XAG 8000 module and 2G / 3G communication with the XAG 8000 3G module.

» External antenna with 0 dBi gain.

» Reports events to 2 IP destinations (monitoring company) plus the Intelbras cloud.

» Operates with xed or dynamic IP.

» Connections to DNS destinations.

» Power from the AMT 8000 alarm panel.

The following gure shows the illustrative image of the XAG 8000 and XAG 8000 3G modules:

ST

100

25V

GPRS XAG 8000 Module and GSM XAG 8000 3G Module

10

Note:

the XAG 8000 and XAG 8000 3G modules are compatible with most national GPRS / GSM operators with 2G and

3G technology and can only be used with the AMT 8000 alarm panel.

3.2. Communication module via telephone line - FXO 8000

Optional accessory dedicated to data transmission via telephone line for communication and event reporting to a

monitoring company with the AMT 8000 security system, in addition to dialing up to 5 personal phones and emitting the

sound of a siren from the telephone line.

Features

» Up to 8 programmable phone addresses.

» DTMF type dialing mode.

» Telephone line cut/interruption check.

» Contact-ID communication protocol.

» Power supply from the AMT 8000 alarm center.

The following gure shows the illustrative image of the FXO 8000 module:

+

10

50G

682

FX8000

4640353/P/4P

108XXXX

LINHA FONE

FXO 8000 Telephone Line Module

3.3. Wireless keyboard for alarm centers– XAT 8000

Optional dedicated accessory to congure, check status and operate the AMT 8000 alarm center. Communication between

the keyboard and the center is made through a wireless signal, providing a simpler installation and long communication

range. Up to 16 XAT 8000 keyboards can be added to each AMT 8000 alarm center.

Features

» Monochrome character liquid crystal screen with 3 lines:

» 1st line for graphic icons (alarm center battery charge indication, problem indication and siren activated).

» 2nd message line with 14 segments.

» 3rd message line with 14 segments.

» Keyboard with illumination on the keys.

» Cover for protection against accidental activation of the keys.

» Light sensor to activate the illumination of the display and keys.

» Display of problems.

» Wireless communication with the alarm center (915 to 928 MHz) via internal antenna, power 11 dBm.

» Simplies the programming of the alarm center.

» Text message display.

» Display of the battery level of the alarm center.

» Display of zone status (open/closed).

» Signs the status of the partitions.

»

Panic, Medical Emergency

and

Fire

function.

» Violation protection (tamper).

11

» Sound signalling during operation.

» DC Power:4 batteries 3 Vdc (CR2450) included.

» Communication supervision and encrypted transmission.

» Range: up to 600 m with direct view in open eld.

The following gure shows the illustrative image of the keyboard:

1 2 3

4 5 6

7 8

0

9

XAT 8000 Wireless Keyboard

The keyboard has two tamper keys, one of which is located on the front of the keyboard, under the cover, is activated by

moving the keyboard cover, its function is to activate the keyboard and the other key, located on the back of the keyboard

cabinet is functioning as tamper (violation protection). On the front of the XAT 8000 there is the light conductor for the

brightness sensor, which has the function of controlling the intensity of the display and keyboard for battery optimization.

The keyboard can be installed on different surfaces, always placing it in the vertical position in relation to the oor and

using double-sided tape or screws (not included) to x the base and after attaching the device, tting and checking that it

was placed correctly so that there are no falls and damage.

3.4. XAC 8000 remote control

Optional dedicated accessory for interface between user and alarm center. Allows to activate, deactivate and perform other

functions together with the alarm center with three keys and light identication of events. Up to 98 XAC 8000 controls can

be added for each AMT 8000 alarm center.

Features

» Visual indication of communication with the system through a two-color LED.

» 3 programmable buttons.

» Wireless communication with the alarm center (915 to 928 MHz) via internal antenna.

» Power 11 dBm.

» DC Power Supply:1 internal 3 Vdc (CR2032) battery of long duration.

» Encrypted transmission.

» Range: up to 200 m with direct view in open eld.

The following gure shows the illustrative image of the control:

XAC 8000 remote control

12

3.5. Wireless siren - XSS 8000

Optional dedicated accessory for status audible warning, intrusion and emergency indications from the AMT 8000 alarm

center. Communication between the siren and the center is made through a wireless signal, providing a simpler installation

and long communication range. Up to 16 XAC 8000 sirens can be added for each AMT 8000 alarm center.

» Features Sound power from 100 dB to 1 meter.

» Communication status check through LED.

» Audible trigger if communication is lost with the alarm center.

» Wireless communication with the alarm center (915 to 928 MHz) via internal antenna, power 11 dBm.

» DC Power Supply:1 Li-SoCl2 3.6 V / 14 A non-rechargeable battery with wire/connector - included.

» Communication supervision and encrypted transmission.

» Range: up to 600 m with direct view in open eld.

The following gure shows the illustrative siren image:

XSS 8000 Wireless Siren

XSS 8000 siren has a tamper key against violation, located at the back of the siren, and if this key is opened/violated,

registered sirens will trigger and send the corresponding event if the

Problems that generate trigger

function is enabled

(see section

Problems that generate trigger

).

Siren can be installed on several surfaces, always placing it in a vertical position with a height between 1.80 and 2.20

meters from the oor and using double-sided tape or screws (not included) to x the base and after securing the device,

tting and checking that it has been placed correctly so that there are no falls and damage. The status of the siren

communication with the alarm center will be represented on it through the indicator LED located on the front, and when

in normal communication the LED will ash green, with partial communication orange and no communication red (the

indicator LED after 15 minutes will enter hibernation mode for battery saving, not hindering the device communication and

to activate again press the device synchronisation key once).

3.6. Wireless magnetic sensor - XAS 8000

Optional dedicated accessory for door and window open checking in a distinctive, discreet and compact design. With low

battery indication and sensor communication status, supervision, activation and anti-violation system with internal tamper

to compose the 8000 line security system with maximum results.

Features

» Wireless communication with the alarm center (915 to 928 MHz) via internal antenna, power 11 dBm.

» Communication status check through LED.

» Fastening by screws (not included) or double-sided tape (not included).

» DC Power Supply:1 CR2450 type 3 Vdc battery of long life lithium.

» Communication supervision and encrypted transmission.

» Range: up to 600 m with direct view in open eld.

13

The following gure shows the illustrative image of the XAS 8000 sensor:

XAS 8000 aperture sensor

XAS 8000 sensor has a tamper key against violation, and if this key is opened/violated, registered sirens will trigger and

send the corresponding event if the

Problems that generate trigger

function is enabled (Problems that generate trigger).

The status of the sensor communication with the alarm center will be represented on it through the indicator LED located

on the front, and when in normal communication the LED will ash green, with partial communication orange and no

communication red (the indicator LED after 15 minutes will enter hibernation mode for battery saving, not hindering the

device communication and to activate again press the device synchronisation key once).

3.7. Passive infrared wireless sensor - IVP 8000 Pet

Dedicated accessory for checking intrusions through infrared reading in indoor environments, in a discreet and compact

way and taking into account the presence of a pet and not triggering the alarm. With low battery indication and sensor

communication status, supervision, activation and anti-violation system with internal tamper to compose the 8000 line

security system with maximum results.

Features

» Wireless communication with the alarm center (915 to 928 MHz) via internal antenna, power 11 dBm.

» Communication status check through LED.

» Coverage of 12 meters by 90°.

»

Pet

function with detection ≥20 kg.

» Fastening by screws (not included) or double-sided tape (not included).

» DC Power Supply:1 CR123A type 3 Vdc battery of long life lithium.

» Communication supervision and encrypted transmission.

» Range: up to 600 m with direct view in open eld.

The following gure shows the illustrative image of the IVP 8000 sensor:

IVP 8000 Pet presence sensor

14

IVP 8000 Pet sensor has a tamper key against violation, and if this key is opened/violated, registered sirens will trigger and

send the corresponding event if the

Problems that generate trigger

function is enabled (see section

Problemas que geram

disparo

). The status of the sensor communication with the alarm center will be represented on it through the indicator LED

located on the front, and when in normal communication the LED will ash green, with partial communication orange and

no communication red (the indicator LED after 15 minutes will enter hibernation mode for battery saving, not hindering

the device communication and to activate again press the device synchronisation key once).

3.8. Passive infrared wireless sensor - IVP 8000 Pet Cam

Dedicated accessory for checking intrusions through infrared reading in indoor environments, in a discreet and compact

way and taking into account the presence of a pet and not triggering the alarm. It has a camera that after the sensor

triggering, sends the image of the site to the applications and software compatible with the AMT 8000 Alarm Center. With

low battery indication and sensor communication status, supervision, activation and anti-violation system with internal

tamper to compose the 8000 line security system with maximum results.

Features

» Wireless communication with the alarm center (915 to 928 MHz) via internal antenna, power 11 dBm.

» Communication status check through LED.

» Coverage of 12 meters by 90°.

»

Pet

function with detection ≥20 kg.

» Takes two pictures per shot. Attending therefore light and dark environments / night period.

» Fastening by screws (not included) or double-sided tape (not included).

» DC Power Supply:2 CR123A type 3 Vdc batteries of long life lithium.

» Communication supervision and encrypted transmission.

» Range: up to 600 m with direct view in open eld.

The following gure shows the illustrative image of the IVP 8000 Pet Cam sensor:

Presence sensor with IVP 8000 Pet Cam camera

IVP 8000 Pet Cam sensor has a tamper key against violation, and if this key is opened/violated, registered sirens will

trigger and send the corresponding event if the

Problems that generate trigger

function is enabled (see section

Problems

that generate trigger

). The status of the sensor communication with the alarm center will be represented on it through the

indicator LED located on the front, and when in normal communication the LED will ash green, with partial communication

orange and no communication red (the indicator LED after 15 minutes will enter hibernation mode for battery saving, not

hindering the device communication and to activate again press the device synchronisation key once).

3.9. Universal Transmitter – TX 8000

Optional accessory dedicated to receive wired sensor signals and transmission of this reading to the AMT 8000 alarm

center. The operation of this device is the same as that of a XAS 8000 wireless magnetic sensor, but it will be activated

every time another sensor has an opening/closing and sends the signal via a pair of wires of the dry contact type (NO or

NC), thus transforming a wired sensor into a wireless one.

15

Features:

» Wireless communication with the alarm center (915 to 928 MHz) via internal antenna, power 11 dBm.

» Communication status check through LED.

» Fastening by screws (not included) or double-sided tape (not included).

» DC Power Supply:1 CR2450 type 3 Vdc battery of long life lithium.

» Communication supervision and encrypted transmission.

» Range: up to 600 m with direct view in open eld.

The following gure shows the illustrative image of the TX 8000 transmitter:

TX 8000 Wired Sensor Transmitter

TX 8000 transmitter has a tamper key against violation, and if this key is opened/violated, registered sirens will trigger and

send the corresponding event if the

Problems that generate trigger

function is enabled (see section

Problemas que geram

disparo

). The status of the sensor communication with the alarm center will be represented on it through the indicator LED

located on the front, and when in normal communication the LED will ash green, with partial communication orange and

no communication red (the indicator LED after 15 minutes will enter hibernation mode for battery saving, not hindering

the device communication and to activate again press the device synchronisation key once).

Attention: the sensors can be installed on different surfaces, always respecting the best position and height for the sensor

to read data correctly. Use double-sided tape or screws (not included) to x the base and after attaching the device, tting

and checking that it was placed correctly so that there are no falls and damage. Observe the maximum communication

distance of the devices with the alarm center.

Range RF Amplier (REP 8000 Repeater)

Optional dedicated accessory for amplifying the RF range between the AMT 8000 alarm center and the other devices.

Communication between the repeater and the center is made through a wireless signal, providing a simpler installation

and long communication range. Repeater can be installed at a distance of 600 meters from the alarm center without

barriers and the other devices at 600 meters from the repeater, also without barriers. Extending the range of the alarm

center from 600 m to 1200 m without barriers.

Features:

» Range: up to 600 m with direct view in open eld.

» Amplier of the coverage area of the AMT 8000 system.

» Protection against malicious signals.

» Cryptography in data transmission between devices.

» Easy installation and handling.

» Amplication of the RF signal up to 600 meters beyond the maximum limit for communication with the alarm center, so

with the use of the amplier a device can communicate at a distance of up to 1.2 kilometers with the alarm center in the

case of direct view and without barriers.

» Rechargeable battery.

» Includes 7 Vdc/500 mA source.

Important: each AMT 8000 alarm center can have up to 4 repeaters operating simultaneously, but all in separate

operation from each other, so there is no possibility of one repeater being used to extend the signal to another, only in

direct use between devices and alarm center.

16

The following gure shows the illustrative image of the repeater:

Range RF Amplier (REP 8000 Repeater)

Range RF Amplier (REP 8000 Repeater) has a tamper key against violation, located at the back of the repeater, and if this

key is opened/violated, registered sirens will trigger and send the corresponding event if the

Problems that generate trigger

function is enabled (see the

Problems that generate trigger

section).

The installation of the Range RF Amplier (REP 8000 Repeater) can be on various surfaces, always placing it in a vertical

position with a height between 1.80 and 2.20 meters from the oor and using double-sided tape or screws (not included)

to x the base and after securing the device, tting and checking that it has been placed correctly so that there are no

falls and damage. The status of the repeater communication with the alarm center will be represented on it through the

indicator LED located on the front, and when in normal communication the LED will ash green, with partial communication

orange and no communication red (the indicator LED after 15 minutes will enter hibernation mode for battery saving, not

hindering the device communication and to activate again press the device synchronisation key once).

4. Installation of the alarm center and its peripherals

Attention: only connect the AMT 8000 alarm center to the mains and battery after the installation of all equipment and

peripherals.

Open the product box and then open the cover of the AMT 8000 alarm center cabinet by removing the screws, where two

plates can be seen, that is, its basic conguration contains the AMT 8000 alarm center board and its respective power

supply and rechargeable battery that comes with the system.

telephone, GPRS and GSM, these cards with their respective interconnection cables with the AMT 8000 exchange.

If you choose the full conguration, 4 boards must be installed in the alarm center cabinet (the alarm center board, the

source board, the telephone line module and the GPRS module or GSM module).

AMT 8000 alarm center has only wireless zones, as well as other accessories (keyboard, sirens, etc.) are connected to the

alarm center via wireless signal, with only the AC power cables, telephone line and Ethernet network cable connected to

the alarm center.

17

Image below illustrates the alarm center with all the devices that can be physically connected:

AMT8000

SENTIDO DE SOLDA

12524

23

22

2

3

4

5

6

7891011

12

1314

15

16

18

19

20

21

17

26

AMT 8000 Alarm Center

1. Connector for network cable (Ethernet).

2. CPU card of the AMT 8000 alarm center.

3. Mini-USB type connector for alarm center rmware update.

4. Alarm center CPU card indicator LED.

5. Alarm center board connector for interconnecting the FXO 8000 telephone line module.

6. Alarm center board connector for interconnecting the XAG 8000 GPRS/GSM module.

7. Pin-type connector (2×5-way) for rmware update of the alarm center.

8. Key for wireless device registration.

9. Input connector for telephone line.

10. Output connector for telephones.

11. CPU board for FXO 8000 telephone line module.

12. Flat cable connector for the XAG 8000 module.

13. Connector for SIM 1 card and SIM 2 card.

14. Connector for external antenna of the XAG 8000 GPRS module.

15. CPU card of the XAG 8000 GPRS module.

16. External GSM antenna (included with XAG 8000 module).

17. Connector for at cable for the output of the telephone line signal to the alarm center board.

18. 3.7 V battery.

19. Flat cable connector for DC output from power supply.

20. Input connector for two-way battery cable.

21. XFT 8000 power supply board.

22. Protection fuses (2 x 250 Vac/400 mA).

23. Connector to connect the ground to the power supply (ground).

24. AC input of the power supply (switched full range - 90 to 265 Vac).

25. Flat cable input of the power supply.

26. Radio connector (future use).

18

Attention: the AMT 8000 alarm center does not have an auxiliary output to feed other devices and no connection point

must be used on the alarm center cards (alarm center, GPRS card, telephone line card or source) for this functionality,

because besides damaging the alarm center, it may damage the devices due to the alarm center operating at different

voltages according to the circuit.

4.1. Power supply for the alarm center (full range 90 and 265 Vac)

Alarm unit is equipped with a full range switching source that works with the input voltage of 90 and 265 Vac without the

need of a voltage selector switch. This way, even if some voltage variation occurs in the mains, the alarm unit will continue

working normally (as long as the voltage is in the range of 90 to 265 Vac).

On this board there are two protection fuses of the unit. If you need to change, use new ones of the same value (250

V/400 mA).

To connect the AC mains input and also to ground, it is recommended to use a three pin cable with a gauge of 1 mm or

higher.

The output to the alarm center board is 5.7 Vdc and 1.7 A.

CN3

Q1 Q2

R3

R5

C7

JP1

CN3

TERRA

CN2

CL2

TR1

D1

R4

UR1

CN1

TE

OK

U1

12

L3

L1

FONE

LINHA

108XXXX

XFT8000

4640511/0/8P

TRIGON 1721a

YEE19V-9P2.03MHA

Terra

Rede AC

Fusíveis

Conector bateria

Conector para a central

Ground

Fuses

AC Mains

Connector for the alarm

center

Battery connector

XFT 8000 Power Supply

Connect the source ground terminal as shown above to the local electrical installation ground.

If the local electrical installation is not grounded, install a grounding bar and wire the connection terminal to the alarm

center to perform the correct grounding.

Attention: it is mandatory to connect the grounding to the alarm center in order to have greater protection against

lightning and overload by the mains and/or telephone line. If this connection is not made, the alarm center will function

normally, but will be unprotected against overloads.

Warranty does not cover possible damages caused by lightning to the alarm center or to any other equipment connected

to it.

4.2. Battery

AMT 8000 alarm center has an internal rechargeable battery of 3.7 Vdc and a capacity of 3,000 mA. The battery connector

is located on the power supply board and is used to connect the battery to the alarm system. To wire the battery to this

connector use the cable that comes with it, as shown below.

TERRA

CN2

CL2

CN3

Q1 Q2

R3

R5

C7

JP1

CN3

TR1

D1

R4

UR1

CN1

TE

OK

U1

12

L3

L1

FONE

LINHA

108XXXX

XFT8000

4640511/0/8P

TRIGON 1721a

YEE19V-9P2.03MHA

Rechargeable battery for AMT 8000 alarm center

19

Alarm center has protection against reverse polarity and short circuit in the battery.

The unit also has protection to prevent the battery from being damaged in the event of a mains failure.

If the voltage in the battery is below 2.8 V, the alarm center will switch off in order not to damage the battery.

Battery life of 8 hours with Wi-Fi enabled and 16 hours with Wi-Fi disabled.

Attention: in case battery replacement is required, please contact our accredited service network.

4.3. XAG 8000 GPRS Module

Check that the cable for connection to the alarm center is correctly connected, passing under the board of the FXO

8000 telephone line module (if used), and its installation should be done only with the unit off, to avoid damage to the

equipment and the installer.

In the XAG 8000 module there are two slots to be allocated two chips (SIM card) being superimposed on each other, with

chip 1 being above chip 2. When installing the chips, let the metal contacts of the same face down and insert until the end

of the slot for the correct allocation of chips.

2

1

CHIP

CHIP 1CHIP 2

Chip allocation in XAG 8000 GPRS module

4.4. FXO 8000 Phone Module

Check that the cable for connection to the alarm center is correctly connected, and that it is only installed with the unit off,

to avoid damage to the equipment and the installer.

In the FXO 8000 module there is the

Line

terminal, where the main telephone line (two wires) must be wired, connecting

the

Phone

output (two wires) in the other telephone sets contained in this same line and as can be seen in the image

below:

Line

Phone

Wiring diagram of telephone line in the FXO 8000 module

This connection is necessary so that in case of reporting events or remote accesses, the alarm center is not without

communication or has it interrupted if other phones of the same circuit enter/are in operation. In this case, when reporting

events or remote access, the other phones will be inoperative, because the center will be occupying the line.

4.5. AMT 8000 Alarm Center

AMT 8000 alarm center has a tamper key against violation, and if this tamper switch is opened/violated, registered

sirens will trigger and send the corresponding event if the

Problems that generate trigger

function is enabled (see section

Problems that generate trigger

).

Ethernet cables, AC power and telephone line should be directed through the hole located at the rear of the alarm center.

20

Alarm center can be installed on several surfaces, always placing it in a vertical position with a height between 1.80 and

2.20 meters and using double-sided tape or screws (not included) to x the base and after securing the alarm center,

tting and checking that it has been placed correctly so that there are no falls and damage, and directing the wires in the

dedicated areas.

5. Operation

Once the installation is nished, connect the alarm center to the local mains and the rechargeable battery.

Note:

to connect the AMT 8000 alarm center it is necessary that it is connected to the AC mains and the 5-way cable of

the source is wired to the

Source

connector of the alarm center board, otherwise the alarm center will not power on even if

the same is with battery. With the alarm center on and the battery connected, it will be recharged by the source and when

the AC network is dropped the alarm center will be maintained by battery power.

5.1. Description of the XAT 8000 LCD keyboard indications

The following icons are located on top of the LCD display:

» : If this icon is ashing, it indicates that a trouble has been detected.

» : it will light up whenever there is a shot in the siren

.

» P: with the icon lit, the center is in programming mode.

» Battery: indicates the battery status of the alarm center.

5.2. Display of troubles

The occurrence of troubles is described as follows:

On the XAT 8000 keyboard the icon will ash.

If any trouble is detected, press the up or down arrow keys on the XAT 8000 keyboard to view them. To end the display,

press the

Exit

key.

Note:

if the

Indication of troubles by the siren in the activation/deactivation

function and

Beeping of the siren in the

activation/deactivation

are enabled and if any trouble is detected, 1 long beep will beep on activation and 2 long beeps

on deactivation.

5.3. Description of the LEDs signaling on the alarm center boards

LEDs of alarm center baseplate

LED Status/event Signaling1

LED1/LED2 Disconnected from the Ethernet network LED off

LED1/LED2 Connected to Ethernet network1Flashing LED

LED3 Center off LED off

LED3 Center on Flashing LED

LED3 Center on and registering devices LED lit

1

This status does not mean that the system is connected to the monitoring servers. To view the connection status, observe through the

Menu

function (see section

Connections).

LEDs of XAG 8000 GPRS board

LED Status/event Signaling1

LED1, LED2 Powered (connected to CPU board) LED1 and LED2 constantly on

LED1, LED2 Chip (SIM1 or SIM2) seeking

connection Only the corresponding LED is lit

LED1 Chip 1 (SIM1) connected to servers LED ashing 1 time (connected to server 1),

LED ashing 2 times (connected to server 2)

LED2 Chip 2 (SIM2) connected to servers LED ashing 1 time (connected to server 1),

LED ashing 2 times (connected to server 2)

1

This status does not mean that the system is connected to the monitoring servers. To view the connection status, observe through the

Menu

function (see section

Connections).

Page is loading ...

Intelbras 8000 Slim System User guide

Intelbras 8000 Slim System User guide

Related papers

Other documents