AccelTex Solutions Power 2 Go Installation guide

Brand
AccelTex Solutions
Model
Power 2 Go
Type
Installation guide
1
ATS-POWER2GO-V1
Product Guide
ATS-POWER2 GO-V1VERSION 2 .1
Battery Powered
Hotspot
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
2
ATS-POWER2GO-V1
Product Guide
1.888.406.8906
[email protected]
PRODUCT GUIDE (ATS-POWER2GO-V1)
Contents
Overview ................................................................................................................................................................................................ 2
Product Safety ....................................................................................................................................................................................... 2
Parts ....................................................................................................................................................................................................... 2
Versions ................................................................................................................................................................................................. 3
Ports....................................................................................................................................................................................................... 4
Cradlepoint Router ................................................................................................................................................................................ 5
Additional Help and Support ................................................................................................................................................................. 6
Overview
This is a quick product guide for the ATS-POWER2GO-V1. This version is compatible with the Cradlepoint IBR600 or IBR900
router. Please read through the guide for a better understanding of this battery powered Wi-Fi hotspot solution. NOTE:
This guide assumes that your Cradlepoint IBR600 or IBR900 router has already been configured with a SIM card and the
desired settings.
Product Safety
Always make sure the locks on the case are securely fastened when transporting.
Only use the wall charger that comes with the case when recharging the battery.
Be sure to turn the power off when not in use to conserve the battery power.
Parts
(1) ATS-POWER2GO-V1 AccelTex Power-2-Go Case (1) Cradlepoint IBR600 or IBR900 Router (Not Included)
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
3
ATS-POWER2GO-V1
Product Guide
1.888.406.8906
[email protected]
Versions
•There are different Accelerator Battery Packs that can be used with the Power-2-Go solution. Be sure to use or order
the appropriate version for the desired setup.
a. ATS-POWER2GO-V1
i. ATS-POWER2GO (version with ATS-SSBP-0)
1. Cat6 Output: Passive 48V PoE or Passive 24V PoE
2. Battery Pack: ATS-SSBP-0
ii. ATS-POWER2GO (version with ATS-SSBP-1)
1. Cat6 Output: 802.3af/at PoE or 24V PoE
2. Battery Pack: ATS-SSBP-1
iii. ATS-POWER2GO (version with ATS-SSBP-2)
1. Cat6 Output: 802.3af/at/bt PoE
2. Battery Pack: ATS-SSBP-2
NOTE: These kits can be modified for specific applications. Contact us for more options.
ATS-SSBP-2 Battery Pack
ATS-SSBP-0 Battery Pack
ATS-SSBP-1 Battery Pack
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
4
ATS-POWER2GO-V1
Product Guide
1.888.406.8906
[email protected]
Ports
•On the side of the case, there are three ports.
a. Cat6 Output
i. This PoE output port is activated when
the power switch of the battery pack
(inside the case) is turned to the ON
position.
ii. Be sure to turn the power switch on the
battery pack to the off position when not
using PoE to conserve battery power.
iii. **ATS-POWER2GO w/ Accelerator v0 ONLY**
1. To change the type of PoE on the
port, plug the ethernet cable into
the desired PoE type inside the
case. By default, the Ethernet cord is plugged into
a Passive 48V PoE Output. (The picture to the
right shows the V1 PoE ports as an example.)
2. Be sure to push the switch in the direction of the
desired PoE type when turning the port on.
iv. **ATS-POWER2GO w/ Accelerator v1 ONLY**
1. To change the type of PoE on the port, plug the
Ethernet cable (see picture to right) into the
desired PoE type inside the case. By default, the
Ethernet cord is plugged into the 802.3af/at PoE
Output.
2. Be sure to push the switch in the direction of the desired PoE type when turning the port on.
b. 12.6V Input
i. This port is used in combination with the wall charger to recharge the battery pack.
c. Power Button
i. This button controls the power that goes to the Cradlepoint router. A blue LED indicates the button has
been pressed and power is going to the router.
ii. Remember to disengage the button when the router is not being used.
Cat6 Port
12.6V Input
Power Button
ATS-POWER2GO-V1 PoE Options
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
5
ATS-POWER2GO-V1
Product Guide
1.888.406.8906
[email protected]
Cradlepoint Router
Place either a pre-configured Cradlepoint IBR600 or IBR900 on top of the empty pre-cut slot in the case. Make sure the Wi-Fi
connections are facing to the right side of the case where the Ethernet cable is located. Make all appropriate connections to
the router. Refer to the cable diagram below. Push the router into the pre-cut slot until it is safely secured in place. The
Cradlepoint-2-Go case is now ready for use. Be sure to close and lock the case if transporting.
LTE
Wi-Fi
Wi-Fi
Router
Power
LAN
Connection
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
6
ATS-POWER2GO-V1
Product Guide
1.888.406.8906
[email protected]
Additional Help and Support
For additional help and support, please contact us:
Phone: 1.888.406.8906
Email: info@acceltex.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

AccelTex Solutions Power 2 Go Installation guide

Brand
AccelTex Solutions
Model
Power 2 Go
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents