AccelTex Solutions Ceiling Tile Enclosure Installation guide

Type
Installation guide
1
ATS-CT-XXXX-2x2
Installation Guide
ATS-CT-XXXX-2x2
VERSION 1.1
Ceiling Tile Enclosure
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
2
1.888.406.8906
Step 1
Locate and remove the designated ceiling tile by tilting the tile diagonally.
Step 2
Open ceiling tile enclosure box and remove key from the AP backplate for later use.
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
3
1.888.406.8906
Step 3
Locate cable connector hole and loosen screws until the gap is large enough for RJ45 cable.
Step 4
Push RJ45 cable through the cable connector hole.
Cable
Connector
Hole
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
4
1.888.406.8906
Step 5
Tighten cable connector hole screws until snug against cable. NOTE: Leave enough slack to reach the AP. Do NOT over-
tighten the cable hole screws as this may damage the cable.
Step 6
Turn enclosure over. NOTE: Four secure mounting points are provided per enclosure. Number 12-gauge wire or better should
be used to secure enclosure to ceiling structure for support once placed in the ceiling tile grid.
Secure Mounting Points
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
5
1.888.406.8906
Step 7
Place AccelTex ceiling tile in place. Working above the ceiling route Ethernet cable to enclosure and through ceiling tile cable
entry point. Connect the cable to the 10/100/1000 POE port on the access point (accessible through door). Secure the four
support points to secure ceiling structure using 12 AWG wire or better.
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
6
1.888.406.8906
Step 8
Using the studs on the back of the AP, align them to the slots on the AP backplate of the ceiling tile enclosure.
Step 9
Press the AP studs into the slots of the back plate then slide forward until the AP is seated and secured. TIP: This process can be
accelerated if an adjacent ceiling tile is pushed up so that the installer can apply downward pressure on the ceiling tile
enclosure. However, this is optional and is not a requirement to complete the installation.
The facts and figures herein are carefully compiled to the best of our knowledge and are intended for general informational purposes only.
Responsibility for the use and application of AccelTex Solutions materials rests with the end user. All AccelTex Solutions products are sold pursuant
to the AccelTex Solutions Terms and Conditions of Sale. © 2020 AccelTex Solutions. All Rights Reserved. AccelTex, AccelTex Solutions, the AccelTex
Solutions Logo and other marks are trademarks or registered trademarks of AccelTex Solutions.
7
1.888.406.8906
Step 10
Close and relock the AP panel on the ceiling tile enclosure. Test the network.
Additional Help and Support
For additional help and support, please contact us:
Phone: 1.888.406.8906
Email: info@acceltex.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

AccelTex Solutions Ceiling Tile Enclosure Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI