Assembly Instructions: 2618-5 (Cosmic)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes
above. Shut off the power at the circuit breaker and completely
removetheoldxturefromtheceiling,includingtheoldmounting
strap.
1. Take the mounting strap assembly from the parts bag. Mounting
strap(B)shouldhavemountingscrews(D)attached.Youmayneedto
tightenhexnuts(C)thatholdthescrewsinplace.
2. Use mounting screws (A) and a screw driver to attach mounting
strap(A)tothejunctionbox.
ASSEMBLING THE FIXTURE
3.Rods(J,K,andL)areonthexture’swires.Bymeasuring,determine
thecorrectnumberofrodsneededforproperhangingheight.
To lengthen the xture, add additional rods. If additional rods are
needed,contacttheplaceofpurchasetoorder.
Toshortenthexture,addatleast8to10inchesofwiretothedesired
lengthandtrimthewires.Slideanyexcessrodsoffthexture’swires
to discard.
4. Pull the wires taut through the rods before threading the rods
together.Threadbottomrod(J,K,orL)ontopost(M)atthecenterof
thexture’sbody.
5. Twist the top rod(J,K,orL)intothethreadsofswivelpost(I)of
canopy(F).Locktherod(s)inplacebytwistingthumbscrew(G).Pull
thexture’swiresthroughthetopofcanopy(F).
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
For Customer Service, please
contact the place of purchase.
CONNECTING THE WIRES
6.Haveanassistantsupporttheweightofthexturewhilecompleting
the wiring. Cut away excess wire. Thread the xture’s wires through
canopyloop(H)andnipple(F).Attachthexture’swirestothepower
supplywiresfromthejunctionbox.Connectblacktoblack(orsmooth);
whitetowhite(orribbed);groundtoground(greenorcopper).Twistthe
endsofthewirepairstogether,andthentwistonawireconnector.Make
surealltwistsareinthesamedirection.Ifthereisnogroundwire(green
or copper)comingfromthejunctionbox,locategroundscrew(E) on
mountingstrap(A)andwrapthexture’sgroundwirearoundthegreen
groundscrew(E).Useascrewdrivertosecuregroundscrew(E)ontothe
mountingbracket.Tuckallwiresneatlyintothejunctionbox.
FINISHING THE INSTALLATION
7.Raisecanopy(F)totheceiling.Positionmountingscrews(D)sothattheyprotrudethroughtheopeningsofcanopy(F).Securecanopy
(F)tomountingstrap(B)withdecorativenuts(H).
8.
Installlightbulbs(notprovided)inaccordancewiththexture’sspecications.Donotexceedthemaximumrecommended
wattage.
Yourinstallationiscomplete.Turnonthepowerandtestthexture.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
G
N
D
L
L
J
L
A
E
D
B
C
F
I
H
M
K
G