Hampton Bay 18124-000 Installation guide

UPC

USE AND CARE GUIDE

BELLEFONT SEMI FLUSH CEILING FIXTURE

Questions, problems, missing parts? Before returning to the store call

Hampton Bay Customer Service

8 a.m. - 6 p.m. EST, Monday-Friday

1-877-527-0313

HAMPTONBAY.COM

We appreciate the trust and conﬁdence you have place in the Hampton Bay through the purchase of this ceiling ﬁxture. We strive to

continually create quality products designed to enhance

Thank You

022011617916

SKU 817010

MODEL

18124-000

your home. Visit us online to see our full line of products available for your

home improvement needs. Thank you for choosing Hampton Bay.

2

Table of Contents

.....................................................

2

Safety Information

....................................................

. 2

Warranty

....................................................................

. 2

Pre-Assembly

............................................................

. 2

Planning for a Successful Assembly

2

Package Contents 3

Assembly

4

Care and Cleaning

6

Troubleshooting

6

Safety Information

WARNING: Inspect the wire insulation for any cuts,

abrasions or exposed copper that may have resulted

during shipping. If there is a defect in the wire, do not

continue the assembly operation. Please call our

Customer Service Team at 1-877-527-0313.

CAUTION: Consult a qualified electrician if you have

any electrical questions.

Warranty

The manufacturer warrants this unit to be free from defects in materials and workmanship for a period of one (1) year from date of

purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this

product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of

the

product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,

modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found to have been improperly

installed, setup, or used in any way not in accordance with the instruction supplied with the product. This warranty shall not apply to a

failure of the product as a result of an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not

relating to faulty material or workmanship. This warranty shall not

apply to the finish on any portion of the product, such as surface

and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specially disclaims any

warranty, whether express or implied, of fitness for a particular

purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any

consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair

of said product.

Contact the Customer Service Team at 1-87

7-527-0313 or visit www.hamptonbay.com.

Pre-Assembly

PLANNING FOR SUCCESSFUL

ASSEMBLY

Read all instructions before assembly.

To avoid damaging this product, assemble it on a soft, non-

abrasive surface such as carpet or cardboard.

Keep your receipt and these instructions for proof of purchase.

.................................................

................................................

.............................................................

....................................................

......................................................

HAMPTONBAY.COM

Please contact 1-877-527-0313 for further assistance.

Pre-Assembly (continued)

3

PACKAGE CONTENTS

G CANOPY

N HEX NUT

O RUBBER WASHER

H LAMP BODY

M SOCKET

J THREADED TUBE

P METAL WASHER

Q GLASS SHADE

R DECORATIVE PART

T SLEEVE

X FINIAL

N HEX NUT

W DECORATIVE OVERLAY

DECORATIVE OVERLAY

C GROUND SCREW

E SCREWS

G CANOPY

I THREADED CAPS

D1 WIRE CONNECTOR

A MOUNTING

SCREWS

B MOUNTING PLATE

B1 MOUNTING PLATE

SCREW HOLES

F HEX NUTS

H LAMP BODY

W

G

H

GROUND SCREW

WIRE CONNECTORS

CANOPY (preassembled)

1

2

3

2

LAMP BODY

1

THREADED CAPS

2

1

A

B

C

D1

E

F

Part

Description

Quantity

MOUNTING PLATE

1

MOUNTING SCREWS

1 INCH

1

2

1

2

1

2

I

J

M

N

O

P

Q

R

T

W

SCREWS

SMALL HEX NUTS

THREADED TUBE

SOCKET (preassembled)

MEDIUM HEX NUTS

8/32

1/8

RUBBER WASHER

METAL WASHER

GLASS SHADE

DECORATIVE PART

1

SLEEVE

DECORATIVE OVERLAYS

X FINIAL

1

JUNCTION BOX

(not included)

Assembly

2

4

C GROUND SCREW

E SCREWS

G CANOPY

I THREADED CAPS

D1 WIRE CONNECTOR

A MOUNTING

SCREWS

B MOUNTING PLATE

B1 MOUNTING PLATE

SCREW HOLES

F HEX NUTS

H LAMP BODY

Carefully unpack your new ﬁxture and lay all parts on a clean, level surface.

Package should contain: mounting hardware package and ﬁxture assembly.

Before starting installation of this ﬁxture, disconnect power by turning off

the circuit breaker or by removing the fuse at the fuse box.

1. Thread the two Mounting Screws (A) through the Mounting Screw Holes (B1)

located on the Mounting Plate (B). Mounting Screws (A) should now be facing

the room.

2.

Secure the two Mounting Screws (A) by threading the two Hex Nuts (F) 1/4

of an inch onto the two Mounitng Screws (A).

Place the Mounting Plate (B) with the Ground Screw (C) against the Junction

Box (not included) and secure with two Screws (E).

3.

4. Screw Threaded Tube (J) into Socket (M) and Lamp Body Assembly (H).

5. Secure Threaded Tube (J) with Hex Nut (N).

6. Make your connections to a 120V AC/60Hz circuit. Attach the green or bare

wire from the electrical supply to the green or bare wire from the ﬁxture.

Attach the black or hot wire from the electrical supply

to the black wire from the ﬁxture. NOTE: If a ground wire does not exist

in the Junction Box (not included) , connect the ﬁxture ground wire directly to the

Ground Screw (C), located on the Mounting Plate (B). If you have electrical

questions, consult your local electrical code for approved grounding methods.

7. Secure the wire connections using the Wire Connectors (D1). Wrap the two

wire connections with electrical tape for a more secure connection.

8. Tuck all wires back into the Junction Box (not included) . No loose strands or connections

should be present.

9. Raise the Canopy (G) and Lamp Body Assembly (H) toward the ceiling.

10. Fit the Canopy (G) and the Lamp Body Assembly (H) over the Mounting

Plate (B) so the threaded portions of the two Mounting Screws (A)

protrude through the two holes of the Canopy (G).

11. Secure the Canopy (G) and the Lamp Body Assembly (H) by screwing

the two Treaded Caps (I) over the the two Mounting Screws (A).

12. Install the two light bulbs into Socket (M). DO NOT EXCEED THE

RECOMMENDED WATTAGES. Light bulbs not included.

13. Center the Rubber Washer (O) and then the Metal Washer (P) over

the hole on the inside of the Glass Shade (Q).

14. Gently place the Decorative Part (R) over the Glass Shade (Q).

15. Secure with Hex Nut (N). HAND TIGHTEN ONLY.

16. Place Sleeve (T) over Threaded Tube (J).

17. Place the two Decorative Caps (W) over Sleeve (T) by overlaying one

to the front and one to the back.

18. Secure with Finial (X).

19. Turn power on at the source. Switch on the light.

G CANOPY

N HEX NUT

O RUBBER WASHER

H LAMP BODY

M SOCKET

J THREADED

P METAL WASHER

TUBE

Q GLASS SHADE

R DECORATIVE PART

T SLEEVE

X FINIAL

N HEX NUT

W DECORATIVE PART

1

JUNCTION BOX

(not included)

5 HAMPTONBAY. COM

Please contact 1-877- 527-0313 for further assistance .

Install two 60 Watt maximum standard, Type A bulbs into the socket.

(Bulbs sold separately).

Installing the light bulb

3

Page is loading ...

Questions, problems, missing parts? Before returning to the store call

Hampton Bay Customer Service

8 a.m. - 6 p.m., EST, Monday-Friday

1-877-527-0313

HAMPTONBAY.COM

Retain this manual for future use.

Page is loading ...

HAMPTONBAY.COM

Para obtener asistencia, llama al 1-877-527-0313.

Preensamblado (continuación)r

3

CONTENIDO DEL PAQUETE

G CUBIERTA

N TUERCAS

HEXAGONALES

O ARANDELA

DE GOMA

H CUERPO DE LA

LÁMPARA

M PORTABOMBILLA

J

TUBO

ROSCADO

P ARANDELA

DE METAL

Q PANTALLA DE

VIDRIO

R PIEZA

DECORATIVA

T FUNDA

X REMATE

N TUERCA

HEXAGONAL

W CUBIERTA

DECORATIVA

CUBIERTA

DECORATIVA

C TORNILLO A

TIERRA

E TORNILLOS

G CUBIERTA

I TAPAS

ROSCADAS

D1 CONECTOR DE

CABLE

A TORNILLOS DE

MONTAJE

B PLACA DE

MONTAJE

ORIFICIOS PARA

LOS TORNILLOS

DE LA PLACA

DE MONTAJE

F TUERCAS

HEXAGONALES

H CUERPO DE

LA LÁMPARA

W

B1

G

H

CUBIERTA (preensamblado)

1

2

CUERPO DE LA LÁMPARA

1

TAPAS ROSCADAS

2

1

A

B

C

E

F

Part

Description

Quantity

PLACA DE MONTAJE

1

TORNILLOS DE MONTAJE

1

2

1

2

1

TORNILLO A TIERRA

2

I

J

M

N

O

P

Q

R

T

W

TUERCAS HEXAGONALES

PEQUEÑAS DE 6,35 MM

TUBO ROSCADO

PORTABOMBILLA (preensamblado)

TUERCAS HEXAGONALES

PEQUEÑAS DE 3,17 MM

ARANDELA DE GOMA

ARANDELA DE METAL

PANTALLA DE VIDRIO

PIEZA DECORATIVA

1

FUNDA

CUBIERTAS DECORATIVAS

X REMATE

3

D1

CONECTORES DE CABLE

1

TORNILLOS DE 2,54 CM

CAJA

ELÉCTRICA

(no incluida)

Page is loading ...

Hampton Bay 18124-000 Installation guide

Hampton Bay 18124-000 Installation guide

in other languages

Related papers

Other documents