Cabletron Systems 9A656-04 Configuration manual

9032598-02

9A656-04/9A686-04 Configuration Guide

9A656-04/9A686-04 Conﬁguration Guide i

NOTICE

Enterasys Systems reserves the right to make changes in speciﬁcations and other information contained in this document without prior

notice. The reader should in all cases consult Enterasys Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR

CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR

RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN

ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.



1999 by Enterasys Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005

Printed in the United States of America

Part Number: 9032598-02 February 1999

Enterasys Systems

,

SPECTRUM

, and

LANVIEW

are registered trademarks and

S

ecure

f

ast

,and

SmartSwitch

are trademarks of

Enterasys Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the

operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause interference in which case the user will be required to correct the interference at his own expense.

WARNING:

Changes or modiﬁcations made to this device which are not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Only qualiﬁed personnel should perform installation procedures.

Notice

ii 9A656-04/9A686-04 Conﬁguration Guide

INDUSTRY CANADA NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference

Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A

prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

VCCI NOTICE

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment

(VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be

required to take corrective actions.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT:

Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Enterasys Systems, Inc. (“Enterasys”) that sets forth your rights and

obligations with respect to the Enterasys software program (the “Program”) contained in this package. The Program may be contained in

ﬁrmware, chips or other media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE

TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER

OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT

TO THE PLACE OF PURCHASE FOR A FULL REFUND.

9A656-04/9A686-04 Conﬁguration Guide iii

Notice

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE

. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions

of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as

authorized in writing by Enterasys.

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of

New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF

WARRANTY. Except as may be specifically provided by Enterasys in writing, Enterasys makes no warranty,

expressed or implied, concerning the Program (including its documentation and media).

CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING,

EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN

MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE

FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,

PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL,

OR RELIANCE DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON

PRODUCT, EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL

DAMAGES, OR ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME INSTANCES THE ABOVE

LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer software” submitted with restricted rights

in accordance with Section 52227-19 (a) through (d) of the Commercial Computer Software - Restricted Rights Clause and its successors,

and (c) in all respects is proprietary data belonging to Enterasys and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as deﬁned in the DoD Supplement to the Federal

Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its successors, and use, duplication, disclosure by the Government is subject to

restrictions as set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at 252.227-7013. Enterasys

Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

Notice

iv 9A656-04/9A686-04 Conﬁguration Guide

SAFETY INFORMATION

CLASS 1 LASER TRANSCEIVERS

THE FE-100F3 FAST ETHERNET INTERFACE MODULE, FPIM-05 AND FPIM-07 FDDI PORT

INTERFACE MODULES, APIM-29 AND APIM-29LR ATM PORT INTERFACE MODULES,

ANIM-29/3 , ANIM-29/3LR AND ANIM-39/2 ATM NETWORK INTERFACE MODULES USE CLASS 1

LASER TRANSCEIVERS. READ THE FOLLOWING SAFETY INFORMATION BEFORE

INSTALLING OR OPERATING THESE MODULES.

The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop eliminates the need for

maintenance checks or adjustments. The output is factory set, and does not allow any user adjustment. Class 1 Laser transceivers comply with

the following safety standards:

• 21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).

• IEC Publication 825 (International Electrotechnical Commission).

• CENELEC EN 60825 (European Committee for Electrotechnical Standardization).

When operating within their performance limitations, laser transceiver output meets the Class 1 accessible emission limit of all three

standards. Class 1 levels of laser radiation are not considered hazardous.

SAFETY INFORMATION

CLASS 1 LASER TRANSCEIVERS

LASER RADIATION AND CONNECTORS

When the connector is in place, all laser radiation remains within the ﬁber. The maximum amount of radiant power exiting the ﬁber (under

normal conditions) is -12.6 dBm or 55 x 10

-6

watts.

Removing the optical connector from the transceiver allows laser radiation to emit directly from the optical port. The maximum radiance

from the optical port (under worst case conditions) is

0.8 W cm

-2

or 8 x 10

3

W m

2

sr-1.

Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard.

When viewing the output optical port, power must be removed from the network adapter.

9A656-04/9A686-04 Conﬁguration Guide v

Notice

DECLARATION OF CONFORMITY

Application of Council Directive(s):

89/336/EEC

73/23/EEC

Manufacturer’s Name:

Enterasys Systems, Inc.

Manufacturer’s Address:

35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name:

Mr. J. Solari

European Representative Address:

Enterasys Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards:

EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment:

Networking Equipment, for use in a Commercial or

Light Industrial Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this notice conforms

to the above directives.

Manufacturer Legal Representative in Europe

Mr. Ronald Fotino Mr. J. Solari

___________________________________ ___________________________________

Full Name Full Name

Principal Compliance Engineer Managing Director - E.M.E.A.

___________________________________ ___________________________________

Title Title

Rochester, NH, USA Newbury, Berkshire, England

___________________________________ ___________________________________

Location Location

Notice

vi 9A656-04/9A686-04 Conﬁguration Guide

9A656-04/9A686-04 Conﬁguration Guide vii

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 Using This Guide.......................................................................................... 1-1

1.2 Document Conventions ................................................................................ 1-2

1.3 Overview.......................................................................................................1-3

1.3.1 Distributed Management Framework.............................................. 1-4

1.3.2 ATM Forum Specifications.............................................................. 1-4

1.3.3 ATM Traffic Types........................................................................... 1-4

1.3.4 MIB Support....................................................................................1-5

1.3.5 Distributed Clocking........................................................................1-5

1.3.6 ATM Adaptation Layer (AAL) Support.............................................1-6

1.3.7 Management LAN Emulation Client................................................1-6

1.4 Interface (Port) Numbering........................................................................... 1-6

1.5 Default Settings Upon First Initialization....................................................... 1-7

1.5.1 9A686-04 Initialization Steps...........................................................1-7

1.5.2 Additional Default Settings..............................................................1-9

1.6 Configurable Options..................................................................................1-10

1.6.1 Configurable Options at the System (Chassis) Level....................1-10

1.7 Local Management Screen Elements......................................................... 1-12

1.7.1 Local Management Keyboard Conventions..................................1-14

1.8 Getting Help................................................................................................ 1-15

1.9 Related Manuals......................................................................................... 1-16

CHAPTER 2 SYSTEM CONFIGURATION

2.1 Selecting Local Management Menu Screen Items....................................... 2-2

2.2 Exiting Local Management Screens............................................................. 2-2

2.3 Accessing the Main Menu Screen................................................................ 2-3

2.4 The Main Menu Screen ................................................................................ 2-4

2.5 The Chassis Menu Screen ........................................................................... 2-5

2.6 Chassis Configuration Screen...................................................................... 2-6

2.6.1 Setting the IP Address .................................................................... 2-8

2.6.2 Setting the Chassis Date.................................................................2-9

2.6.3 Setting the Chassis Time................................................................2-9

2.6.4 Entering a New Screen Update Time............................................2-10

2.7 SNMP Community Names Screen ............................................................. 2-11

2.7.1 Establishing Community Names...................................................2-12

Contents

viii 9A656-04/9A686-04 Conﬁguration Guide

2.8 SNMP Traps Screen...................................................................................2-13

2.8.1 Configuring the Trap Table............................................................2-14

2.9 The Chassis Power Screen.........................................................................2-15

2.10 The Module Selection Screen.....................................................................2-17

2.10.1 Selecting a Module........................................................................2-17

2.11 The Module Menu Screen for the 9A686-04...............................................2-18

2.12 The Module Configuration Menu Screen ....................................................2-19

2.13 The General Configuration Screen .............................................................2-20

2.13.1 Entering a New Screen Refresh Time...........................................2-21

2.13.2 Setting the Screen Lockout Time ..................................................2-22

2.13.3 Setting the TFTP Gateway IP Address..........................................2-22

2.13.4 Setting the Default Gateway..........................................................2-23

2.13.5 Setting the Default Interface..........................................................2-23

2.14 The Module Specific Configuration Screen.................................................2-24

2.15 System Configuration Menu Screen ...........................................................2-26

2.16 The PNNI Configuration Screen..................................................................2-27

2.16.1 PNNI Configuration Screen Fields.................................................2-28

2.16.2 Setting the PNNI Mode..................................................................2-31

2.16.3 Setting the NSAP Prefix ................................................................2-31

2.16.4 Setting the PNNI Level..................................................................2-31

2.17 The ILMI Configuration Menu Screen.........................................................2-32

2.17.1 ILMI Configuration Menu Screen Fields........................................2-33

2.17.2 Setting the MIN SVCC VCI Field...................................................2-33

2.17.3 Setting the MAX SVCC VPI Field..................................................2-34

2.17.4 Setting the MAX SVPC VPI Field..................................................2-34

2.18 The ATM Diagnostics Screen .....................................................................2-35

2.18.1 Enabling/Disabling ATM Diagnostics.............................................2-35

2.19 Module Configuration Menu Screen............................................................2-36

2.19.1 Module Configuration Menu Screen Fields ...................................2-36

2.20 Port Status Screen......................................................................................2-38

2.20.1 Port Status Screen Fields..............................................................2-38

2.21 Port Errors Screen ......................................................................................2-42

2.21.1 Port Errors Screen Fields..............................................................2-42

2.22 EPD/PPD Configuration Menu Screen........................................................2-44

2.22.1 EPD/PPD Configuration Menu Screen Fields ...............................2-44

2.22.2 Configuring EPD/PPD ...................................................................2-45

2.23 SPVC Connection Management Menu Screen...........................................2-46

2.23.1 SPVC Connection Management Menu Screen Fields...................2-46

2.24 SPVC Source Creation Screen...................................................................2-47

2.24.1 SPVC Source Creation Screen Fields...........................................2-47

2.24.2 Creating the Source End of an SPVP............................................2-49

2.24.3 Creating the Source End of a SPVC .............................................2-51

9A656-04/9A686-04 Conﬁguration Guide ix

Contents

2.25 SPVC Destination Creation Screen............................................................ 2-53

2.25.1 SPVC Destination Creation Screen Fields.................................... 2-53

2.25.2 Creating the Destination End of an SPVP.....................................2-55

2.25.3 Creating the Destination End of a SPVC ...................................... 2-56

2.26 LAN Emulation Menu Screen ..................................................................... 2-57

2.26.1 LAN Emulation Client Menu Screen Fields...................................2-58

2.27 LAN Emulation Client Properties Screen....................................................2-59

2.27.1 LAN Emulation Client Properties Screen Fields............................2-59

2.28 LAN Emulation Client Administration Screen ............................................. 2-63

2.28.1 LAN Emulation Client Administration Screen Fields.....................2-63

2.28.2 Configuring the LEC Automatically ............................................... 2-65

2.28.3 Configuring the LEC Manually ...................................................... 2-66

2.29 Network Tools.............................................................................................2-67

2.29.1 Built-in Commands........................................................................ 2-68

2.29.2 Special Commands.......................................................................2-74

2.30 The Environmental Module Screen ............................................................ 2-75

2.30.1 Setting the Fan Speeds.................................................................2-77

2.30.2 Enabling/Disabling COM1 and COM2...........................................2-77

2.30.3 Changing the COM2 Application................................................... 2-78

2.30.4 Downloading a New Image into Flash Memory.............................2-78

2.31 Creating a PVC........................................................................................... 2-79

2.31.1 Getting the Traffic Descriptor........................................................2-79

2.31.2 Adjusting ILMI Parameters for PVC Creation................................2-79

2.31.3 Setting the Instance of the First Interface ..................................... 2-81

2.31.4 Setting the Traffic Descriptor for the Receive Side

of the Interfaces ............................................................................ 2-82

2.31.5 Setting the Traffic Descriptor for the Transmit

Side of the Interfaces....................................................................2-83

2.31.6 Setting the VCL Status to Active...................................................2-84

2.31.7 Getting the Cross-Connect Identifier (CCID).................................2-85

2.31.8 Activating the PVC........................................................................2-86

CHAPTER 3 ILMI 4.0 AND THE SMARTSWITCH 9500 SYSTEM

3.1 ILMI Autoconfiguration Examples................................................................. 3-1

3.2 Port Status Screen........................................................................................ 3-5

3.3 ILMI Configuration Screen............................................................................ 3-7

Contents

x 9A656-04/9A686-04 Conﬁguration Guide

CHAPTER 4 SIGNALLING AND ROUTING

4.1 Persistence ...................................................................................................4-1

4.2 Signalling Overview.......................................................................................4-2

4.2.1 Stack Types.....................................................................................4-2

4.2.2 Configuration...................................................................................4-2

4.2.3 Setting Types...................................................................................4-3

4.2.4 Setting Sides ...................................................................................4-5

4.3 Routing Overview..........................................................................................4-7

4.3.1 PNNI Overview................................................................................4-7

4.3.2 Peer Groups....................................................................................4-8

4.3.3 Crankback .......................................................................................4-9

4.3.4 GCAC............................................................................................4-10

4.3.5 Addressing.....................................................................................4-10

4.4 IISP Overview .............................................................................................4-10

4.4.1 Supported UNI Signalling Versions...............................................4-10

4.4.2 UNI Sides ......................................................................................4-10

4.5 Configuring IISP..........................................................................................4-11

4.5.1 Signalling Configuration.................................................................4-12

4.5.1.1 Step 1: Set the IISP Signalling Version and Type.........4-12

4.5.1.2 Step 2: Set the IISP Side...............................................4-14

4.6 Creating and Configuring a Reachable Address (Static Route)..................4-16

4.6.1 Step 1: Create a Row in the pnniRouteAddrTable ........................4-17

4.6.2 Step 2: Associate the Reachable Address with Its

Advertising Node ID.......................................................................4-19

4.6.3 Step 3: Associate the Reachable Address with a Port ID..............4-21

4.6.4 Step 4: Associate the Reachable Address with an Interface.........4-23

APPENDIX A ACRONYMS

APPENDIX B DEFAULT SETTINGS

B.1 SmartSwitch 9500 System Settings................................................................ B-1

B.1.1 IP Addresses........................................................................................ B-1

B.1.2 SNMP Community Names.................................................................... B-1

B.1.3 SNMP Traps......................................................................................... B-1

B.1.4 Signalling.............................................................................................. B-1

B.1.5 ILMI Settings......................................................................................... B-2

B.1.6 Management LAN Emulation Client ..................................................... B-2

B.1.7 PNNI Settings....................................................................................... B-2

B.1.8 Clocking................................................................................................ B-2

B.1.9 Maximum Number of Connections....................................................... B-2

9A656-04/9A686-04 Conﬁguration Guide xi

Contents

APPENDIX C SUPPORTED MIBS

C.1 MIB, SMI, MIB Files and Internet MIB Hierarchy.............................................C-1

C.2 SmartSwitch 9500 MIB Hierarchy ...................................................................C-3

Contents

xii 9A656-04/9A686-04 Conﬁguration Guide

9A656-04/9A686-04 Conﬁguration Guide Page 1-1

CHAPTER 1

INTRODUCTION

Welcome to the Enterasys Systems

9A656-04/9A686-04 Conﬁguration Guide.

This guide

describes the management features of the 9A656-04/9A686-04 and how to conﬁgure the

modules and SmartSwitch 9500 chassis via Local Management screens and MIBs, and

includes information concerning network requirements and troubleshooting.

1.1 USING THIS GUIDE

Read through this guide completely to understand the features, capabilities, Local

Management Functions, and MIB support of the 9A686-04 and the SmartSwitch 9500 chassis.

The following list provides an overview of each section in this manual:

Chapter 1,

Introduction

, provides a brief overview of the management features of the

9A686-04, describes the interface numbering scheme used by the 9A686-04, provides an

overview of the conﬁgurable options of the modules and the entire system (SmartSwitch

9500), provides instructions on getting help and concludes with a list of related manuals.

NOTE

This is a draft manual for the 9A686-04 only. Additional information regarding PNNI

local management screens will be added to the next revision.

NOTE

In this document, the Cabletron Systems SmartSwitch 9000 chassis is referred to

as the “SmartSwitch 9500 chassis” which indicates a SmartSwitch 9000 chassis

with a CTM backplane and one or more 9A656-04/9A686-04 modules installed.

Unless noted differently, this guide applies to both the 9A656-04 and 9A686-04 ATM

SmartSwitch modules, which are referred to as the “9A686-04”.

NOTE

This guide is for Cabletron Systems service personnel and QUALIFIED customer

maintenance personnel who are familiar with installing networking systems, and

have a working knowledge of ATM networks, and for system managers and others

who perform network management tasks.

Chapter 1:

Introduction

Page 1-2 9A656-04/9A686-04 Conﬁguration Guide

Chapter 2,

Basic System Conﬁguration

, provides instructions on setting the In-Band,

Out-Of-Band, and SMB-10 IP Addresses, setting SNMP Community Names and SNMP

Traps, viewing chassis power supply information, creating PVCs and SPVCs, conﬁguring

PNNI for the SmartSwitch 9500, setting ILMI parameters, conﬁguring the management LEC,

and conﬁguring the Environmental Module of the SmartSwitch 9500 chassis.

Chapter 3,

ILMI 4.0 and the SmartSwitch 9500 System

, provides information on how the

SmartSwitch 9500 uses ILMI 4.0 to auto-conﬁgure signalling stacks and sides depending on

the requirements of the network, with no user input required.

Chapter 4,

Signalling and Routing

, provides information and instructions on how to use

MIBs to force individual interfaces to use speciﬁc Signalling stacks and sides, how to

conﬁgure an IISP interface via MIB tools, and provides a brief overview of PNNI 1.0 support

of the SmartSwitch 9500.

Appendix A,

Acronyms

, provides a list of acronyms commonly used in this document.

Appendix B,

Default Settings

, provides information on the default settings the SmartSwitch

9500 system has upon ﬁrst initialization, and cross references to sections of this manual where

these settings may be changed.

Appendix C,

Supported MIBs

, provides tables that detail all of the MIB branches and branch

leaves supported by the SmartSwitch 9500 system.

1.2 DOCUMENT CONVENTIONS

The following conventions are used throughout this document:

NOTE

Note

symbol. Calls the reader’s attention to any item of information that may be of

special importance.

!

CAUTION

Caution

symbol. Contains information essential to avoid damage to the equipment.

TIP

Tip

symbol. Conveys helpful hints concerning procedures or actions.

9A656-04/9A686-04 Conﬁguration Guide Page 1-3

Overview

1.3 OVERVIEW

The following two subsections provide brief overviews of the 9A656-04 and the 9A686-04

respectively:

9A656-04

The 9A656-04 is a 4.5 Gbps, single slot module for the SmartSwitch 9500 chassis. Up to four

ATM Network Interface Modules (ANIMs) of any type can be installed in the 9A656-04 to

provide front panel connectivity to the network. Enterasys Systems ANIMs can support up to

622 Mbps of bandwidth per port. The 9A656-04 switches data between the ANIMs and the

Cell Transfer Matrix (CTM) backplane in the SmartSwitch 9500 chassis. This allows for

high-speed switching of data between modules installed in the same chassis that connect to

the CTM backplane. The CTM provides a dedicated 1.6 Gbps link between each 9A656-04

module.

9A686-04

The 9A686-04 is a 5.4 Gbps, single slot module for the SmartSwitch 9500 chassis. Up to four

ATM Network Interface Modules (ANIMs) of any type can be installed in the 9A686-04 to

provide front panel connectivity to the network. Enterasys Systems ANIMs can support up to

622 Mbps of bandwidth per port. The 9A686-04 switches data between the ANIMs and the

Cell Transfer Matrix (CTM) backplane in the SmartSwitch 9500 chassis. This allows for

high-speed switching of data between modules installed in the same chassis that connect to

the CTM backplane. The CTM provides a dedicated 1.6 Gbps link between each 9A686-04

module.

Chapter 1:

Introduction

Page 1-4 9A656-04/9A686-04 Conﬁguration Guide

1.3.1 Distributed Management Framework

Through its distributed management framework, the 9A686-04 allows all the modules in the

chassis to appear as a single entity, managed through a single IP address. The individual

modules are transparent to the network manager and management applications. A fully loaded

SmartSwitch 9500 chassis appears as a single switch, with one IP address.

1.3.2 ATM Forum Speciﬁcations

The 9A686-04 is fully compliant with the following ATM Forum speciﬁcations:

•

Intergrated Local management Interface (ILMI) 4.0 for autoconﬁguration.

•

UNI v3.0 /3.1 and v4.0 for signalling.

•

ATM Forum P-NNI 1.0 and IISP 3.0/3.1/4.0 routing speciﬁcations for establishing

connections between ATM switches.

•

LANE 1.0 for the management LAN Emulation Client.

•

TM 4.0

1.3.3 ATM Trafﬁc Types

The 9A686-04 supports the following standard ATM trafﬁc classes:

•

Constant Bit Rate (CBR): ATM trafﬁc class that is guaranteed a ﬁxed amount of bandwidth

while the Virtual Circuit (VC) is active.

•

Variable Bit Rate (VBR): ATM trafﬁc class that varies the amount of bandwidth used on the

VC while the VC is active, while maintaining a minimum CBR component.

•

Available Bit Rate (ABR): ATM trafﬁc class that allows VCs to use the greatest amount of

bandwidth available on the link at any point in time.

•

Unspeciﬁed Bit Rate (UBR): ATM trafﬁc class that does not contain any bandwidth

guarantees.

NOTE

“

Throughout this manual, it is important to understand that the 9A656-04/9A686-04

are part of an overall “system” which is the SmartSwitch 9500. With one or more

9A656-04/9A686-04s installed, the chassis becomes a single switch, with all boards

installed being a part of that single switch, not a separate component.

When this manual refers to the “system” it is referring to a SmartSwitch 9500

chassis with one or more 9A656-04/9A686-04 modules installed.

9A656-04/9A686-04 Conﬁguration Guide Page 1-5

Overview

1.3.4 MIB Support

The 9A686-04 provides support for a variety of Industry Standard and Enterasys Systems

speciﬁc MIBs. Details on these MIBs are provided in later chapters of this Guide. The MIBs

supported are as follows:

•

MIB2 (RFC 1573)

•

AToM MIB (RFC 1695)

•

AToM II MIB

•

ILMI MIB

•

PNNI MIB

•

Enterasys MIBs

•

SFCS MIB

•

ctNetwork MIB

•

ctPIC MIB

•

ctFlash MIB

•

nwRouter MIB

•

ctron Mib2 MIB Ext.

1.3.5 Distributed Clocking

The 9A686-04 supports three clocking modes:

Clock Recovery Mode

This clocking mode is required when the 9A686-04 is CONNECTED to the public ATM

network. In this mode, the 9A686-04 derives its transmit clock from the incoming line clock.

Master Clock Distribution

This clocking mode is required when the 9A686-04 is PART of the public ATM network. In

this mode, one 9A686-04 installed in the SmartSwitch 9500 chassis is conﬁgured as the

master clock for all other modules attached to the CTM backplane. The 9A686-04 that is the

master clock then distributes all clocking information to all the other modules.

Local Clock Mode

This clocking mode may be used by the 9A686-04 if the master clock signal is lost, or in the

absence of any external clock source. In this mode each 9A686-04 installed in the chassis acts

as its own clock source.

Chapter 1: Introduction

Page 1-6 9A656-04/9A686-04 Conﬁguration Guide

1.3.6 ATM Adaptation Layer (AAL) Support

The 9A686-04 support all ATM Adaptation Layers, (AAL 1, AAL 3/4 and AAL 5).

1.3.7 Management LAN Emulation Client

The SmartSwitch 9500 system creates a default management LEC upon ﬁrst initialization.

The LEC automatically joins the default ELAN. Although all modules in the chassis are

capable of becoming the LEC, only one LEC is active in the system at one time. This is

accomplished through a LEC election algorithm.

1.4 INTERFACE (PORT) NUMBERING

The 9A686-04 use a geographic interface numbering scheme that allows for easy identiÞca-

tion of each front panel and backplane interface of each 9A686-04 installed in the Smart-

Switch 9500 chassis. Interface numbers are generated as follows:

Slot ##, ANIM ##, Interface ##

Table 1-1 provides an example of how the interface numbering scheme works. In this

example, there is a SmartSwitch 9500 chassis with ﬁve 9A686-04 modules installed. These

modules are installed in slots 1, 3, 7, 11 and 14. Each of these modules are equipped with 4

ANIM 21/3s. This provides each 9A686-04 with 12 front panel interfaces. Refer to Table 1-1

for a breakdown of the interface numbering scheme.

Table 1-1 Interface (Port) Numbering Example

ANIM # Interface # Slot 1 Slot 3 Slot 7 Slot 11 Slot 14

1 1 10101 30101 70101 110101 140101

1 2 10102 30102 70102 110102 140102

1 3 10103 30103 70103 110103 140103

2 1 10201 30201 70201 110201 140201

2 2 10202 30202 70202 110202 140202

2 3 10203 30203 70203 110203 140203

3 1 10301 30301 70301 110301 140301

3 2 10302 30302 70302 110302 140302

3 3 10303 30303 70303 110303 140303

4 1 10401 30401 70401 110401 140401

4 2 10402 30402 70402 110402 140402

4 3 10403 30403 70403 110403 140403

Page is loading ...

Cabletron Systems 9A656-04, 9A686-04 Configuration manual

Related papers

Other documents