Eaton MEM Memera User manual

Eaton
Brand
Eaton
Model
MEM Memera
Type
User manual
MEM
姞
Memera
Consumer unit
Important notes
1. This product should be installed, commissioned and maintained by or under the supervision of a competent electrician
in accordance with current electrical engineering Codes of Practice, Regulations for the Electrical equipment of
Buildings (BS7671), HSG224 – Construction (Design and Management) Regulations 1994, HSG150 – Health and
Safety in Construction, Statutory requirements and any Specifi c instruction issued by the Company.
2. After completing the installation and testing of this product it is essential that this leafl et is drawn to the attention of
the person responsible for its future operation and maintenance, and is at all times available for ready reference.
3. These notes assume throughout that the product is disconnected from the supply.
It is essential that this is done before any work is carried out.
1. This Consumer Unit must be installed by a competent person in accordance with BS7671 IEE Regulations for
electrical Installations with the requirements of all relevant legislation, and Accepted practices in the industry.
2. The total current supplied by the Consumer Unit must not exceed the rating of the incoming
main switch, RCD or any additional limitations (as shown on the Way Labels).
3. This board is suitable for indoor use only and is rated at IP40.
4. Ambient Temperature Conditions:
The MCB’s are calibrated to meet 35°C according to requirements laid down in IEC/EN60898. For other
temperatures the following rating factor should be used: 60°C - 0.85, 20°C - 1.0, 0°C - 1.1
5. All components used in the EATON MEMERA CONSUMER UNIT must be supplied by or approved by EATON. The use of any
other components within the EATON MEMERA CONSUMER UNIT will negate any warranty issued by EATON ELECTRIC LTD.
6. The consumer unit and appropriate devices have been type tested to the following specifi cations:
MCB’s IEC/EN 60898
RCCD’s IEC/EN 61008-1
RCBO’s IEC/EN 61009-1
Main Switch IEC/EN 60947-3
Consumer Unit IEC/EN 60493-3
Eaton Electric Limited
Reddings Lane
Birmingham B11 3EZ
United Kingdom
Customer Support Centre
UK tel: +44(0) 8700 545 333
UK fax: +44(0) 8700 540 333
email: [email protected]
www.eaton.com
© 2009 Eaton Corporation
All Rights Reserved
Printed in UK
Form No. IL01900001U
March 2009
PowerChain Management is a registered
trademark of Eaton Corporation.
All other trademarks are property of their
respective owners.
Remove the main outer cover from the
EATON MEMERA CONSUMER UNIT
1. Remove the Busbar from the transit holder.
2. Fix the back plate to the wall using the keyhole Fixings
CAUTION: DO NOT BEND & RE-STRAIGHTEN THE BUSBAR
When fi tting the Busbar into the isolator ensure that the fl exible
live connector is fi tted beneath the busbar in the box clamp.
Fit the busbar Shield into the base and
over the unprotected Busbar.
Fit the busbar Shield into the base and
over the unprotected Busbar.
Remove the appropriate “Knockouts” for cable entry.
Cut the Busbar to the desired length (number of ways
plus one tongue) the raised “Dog leg portion of the
busbar must be fi tted to the Main Switch. Ensure the full
portion between tongues is removed and discarded.
CABLE CAPACITY AND TORQUE SETTINGS
CABLE CAPACITY
ISOLATOR 2.5Nm 50mm
2
RCD/RCBO 2.5Nm 25mm
2
OTHERS 2.0Nm 25mm
2
Fit the Busbar/s: Ensure all terminals are fully open before installing
the busbar, tighten all connections to the specifi ed torques.
Apply the Instruction Label & RCD resetting instructions
(where applicable) to the inside of the door.
Affi x the required main circuit identifi cation labels
& Sub circuit identifi cation for RCD protected
circuits, for split loads cut as required.
Warning – Intellectual Property Rights
Eaton wishes to make it clear that it owns intellectual property rights in the product
which it manufactures (whether or not listed in this leafl et) and that it will take legal
action against any party found to be manufacturing, using, or selling any article which
infringes the company’s intellectual property. All marks in this document identifi ed
with an R symbol or a TM symbol adjacent to the mark are trademarks of Eaton.
The use to which this product is put and its place of installation is outside our control.
Particular care should therefore be taken to follow the instructions given here and
to ensure their continued availability in conjunction with the use of the product.
No responsibility can be accepted by us if these instructions are disregarded. Further
copies of these instructions and information concerning the installation and proper use
of this product can be obtained by contacting the: Technical Services Department
  • Page 1 1
  • Page 2 2

Eaton MEM Memera User manual

Eaton
Brand
Eaton
Model
MEM Memera
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents