Eaton Memera Series Instruction Leaflet

Eaton
Brand
Eaton
Model
Memera Series
Type
Instruction Leaflet

Eaton Memera Series is a range of full metal 2/4 way DIN rail boxes designed for use with EMS631N and EMS1001N isolator devices. The boxes are suitable for copper connections only and have been type tested to the following specifications: Main Switch: IEC/EN 60947-3. The boxes have sealing areas for incoming and outgoing connections of isolator main switches, and all unused sub circuit positions must have an associated blank plate fitted in the box cover. The terminals are suitable for copper connections only.

Eaton Memera Series is a range of full metal 2/4 way DIN rail boxes designed for use with EMS631N and EMS1001N isolator devices. The boxes are suitable for copper connections only and have been type tested to the following specifications: Main Switch: IEC/EN 60947-3. The boxes have sealing areas for incoming and outgoing connections of isolator main switches, and all unused sub circuit positions must have an associated blank plate fitted in the box cover. The terminals are suitable for copper connections only.

170443086
Version 2
1
EATON
®
Memera
EAN Full Metal 2/4 Way DIN Rail Box - EAN2SEBD, EAN4SEBD
Important notes
1. This product should be installed, commissioned and maintained by or under the supervision of a
competent electrician in accordance with the current electrical engineering Codes of Practice, BS7671
(IET Wiring Regulations), Statutory requirements, and any specific instructions issued by Eaton.
2. After completing the installation and testing of this product it is essential that the user instruction leaflet is
drawn to the attention of the person responsible for its future operation and maintenance and is at all
times available for ready reference.
3. These notes assume throughout that the product is disconnected from the supply. It is essential that this
is done before any work is carried out.
4. The use to which this product is put and its place of installation is outside of Eaton´s control. Particular
care should therefore be taken to follow these instructions and to ensure their continued availability in
conjunction with the use of the product. No responsibility can be accepted by Eaton if these instructions
are disregarded.
5. Further copies of these instructions and information concerning the installation and proper use of this
product can be obtained by contacting:
Eaton Electric Limited
Grimshaw Lane
Middleton, Manchester M24 1GQ
United Kingdom
Customer Support Centre
UK tel: +44(0) 8700 545 333
UK fax: +44(0) 8700 540 333
email: ukcomm[email protected]
www.eaton.com
EAN2SEBD
EAN4SEBD
Sealing area for
incoming connection
of Isolator main switch
Sealing area for
incoming connection
of Isolator main switch
Sealing area for
outgoing connection
of Isolator main switch
Sealing area for
outgoing connection
of Isolator main switch
2
Installation instructions
1. Normal precautions should be taken to guard against swarf/dust entering isolators and any remaining
debris in the bottom of the box should be removed.
2. All unused sub circuit positions must have an associated blank plate fitted in the box cover. Ensure all
terminal shields are replaced.
3. Appropriate Isolator devices: EMS631N, EMS1001N
4. The EAN Full Metal Box and appropriate devices have been type tested to the following specifications:
Main Switch : IEC/EN 60947-3
Wall fixing / dimensions
Torque settings and cable capacity
ISOLATOR – 2,5 Nm – 50 mm²
Earth points: 2,0 Nm – M5 bolt for cable lug
Important: Tighten all connections to the specified torques, including factory made connections.
The terminals are suitable for copper connections ONLY.
Testing of the installation
1. After completion of the installation, it is essential that a test is carried out in accordance with the latest
Edition of the BS7671 (IET Wiring Regulations).
2. It is important that the following are included in 1 above:
Check that all connectors, are fitted correctly and all screw type connections are tightened
sufficiently.
Warning – Intellectual Property Rights
Eaton wishes to make it clear that it owns intellectual property
rights in the product which it manufactures (whether or not listed
in this leaflet) and that it will take legal action against any party
found to be manufacturing, using, or selling any article which
infringes the company’s intellectual property. All marks in this
document identified with an R symbol or a TM symbol adjacent
to the mark are trademarks of Eaton.
The use to which this product is put and its place of installation is
outside our control.
Particular care should therefore be taken to follow the
instructions given here and to ensure their continued availability
in conjunction with the use of the product.
No responsibility can be accepted by us if these instructions are
disregarded. Further copies of these instructions and information
concerning the installation and proper use of this product can be
obtained by contacting the: Technical Services Department
Eaton Electric Limited
Grimshaw Lane
Middleton, Manchester M24 1GQ
United Kingdom
Customer Support Centre
UK tel: +44(0) 8700 545 333
UK fax: +44(0) 8700 540 333
email: ukcommorders@eaton.com
www.eaton.com
© 2015 Eaton Corporation
All Rights Reserved
Form No. IL01900001U
October 2015
  • Page 1 1
  • Page 2 2

Eaton Memera Series Instruction Leaflet

Eaton
Brand
Eaton
Model
Memera Series
Type
Instruction Leaflet

Eaton Memera Series is a range of full metal 2/4 way DIN rail boxes designed for use with EMS631N and EMS1001N isolator devices. The boxes are suitable for copper connections only and have been type tested to the following specifications: Main Switch: IEC/EN 60947-3. The boxes have sealing areas for incoming and outgoing connections of isolator main switches, and all unused sub circuit positions must have an associated blank plate fitted in the box cover. The terminals are suitable for copper connections only.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents