ATB6600
Blender
USER MANUAL
PLEASE KEEP THIS USER MANUAL FOR FUTURE USE.
2
USER MANUAL CONTENTS
SAFETY INSTRUCTIONS.......................................................2
BEFORE USE.........................................................................4
PACKAGE CONTENTS.......................................................4
APPLIANCE OVERVIEW.....................................................4
ASSEMBLING YOUR BLENDER............................................5
USING THE BLENDER...........................................................6
CLEANING AND MAINTENANCE .................................7
SAFETY INSTRUCTIONS
• Should damages be found on the appliance, its power cord and/or
its other components – do not use the appliance and immediately
bring it to the Aztech Service Center for repair or replacement.
• Before use, please check if the power voltage of your Blender
correctly corresponds to your home’s power supply.
• Ensure that the Blender is unplugged from the power outlet before
assembling and/or removing attachments.
• Before plugging your appliance’s power adapter into a power outlet,
ensure that the Blender is OFF. In addition, before unplugging your
appliance from the power outlet, ensure that the appliance is OFF
as well.
• Always handle the appliance with care.
• Do not use hot liquids on the appliance and/or operate the Blender
without any ingredients present.
• Do not use your Blender in blending hard and dry substances since
these may blunt your Blender’s blades.
• Always operate the Blender with the jug cover in place.
• Ensure that all parts and/or components are attached and properly
locked into place.
• Do not, in any kind of manner, disassemble, dismantle, and/or perform
appliance repair on your own and/or replace its components using
non-Aztech approved components and/or attachments.
• Do not use the appliance and/or its components for anything other
than its intended purpose. The appliance is intended for household use
only, commercial usage would void the warranty of the appliance.
NOTE: It is STRONGLY ADVISED to ensure that you have read all provided safety
guides and operating instructions in this user manual rst before proceeding.
3
• Do not leave the Blender unattended.
• Do not use wet hands in inserting or removing its power adapter to
prevent electrical shocks. It is recommended to thoroughly dry your
hands rst before every use.
• Whenever plugging the Blender, ensure that the Speed Selector is set
to OFF position.
• The max operation period per cycle should not exceed 3 minutes.
Please provide a 3-minute rest period in between two continuous
blending cycles.
• Do not position the appliance in a humid environment and/or in
places exposed to multiple sources of heat such as stoves, or ovens. It
is also important to keep it away from combustible materials such as
electric burners, curtains and/or cloths especially during use.
• During use, avoid contact with moving parts.
• Do not let its power cord hang over edges of table and/or touch hot
surfaces which may damage the appliance nor use its power cord in
carrying the appliance.
• Always unplug the unit before cleaning and/or even after usage.
• Keep the appliance out of reach of children. If children are within
the area during use, ensure to operate the appliance with extra care
for safety purposes. Keep its power cord safely kept away and out of
reach during use to avoid unwanted accidents.
• When unplugging its power adapter, do not pull or tug its cord. Hold
the power adapter rmly on its base when unplugging it from the
power outlet. Also, ensure that its power cord is kept away from any
source of heat and/or sharp edges that may cause external damage
to the cord.
• Do not immerse or expose your Blender’s main body and/or its power
cord to water or any kind of liquid substance.
• Your Aztech Blender is not intended for people with reduced
physical, sensory or mental capabilities, and/or lack of experience
or knowledge. Constant supervision (from a person responsible for
their safety) should be provided if such individuals would be using,
cleaning, or operating, the appliance.
4
PACKAGE CONTENTS
• ATB6600 Blender
• Inner Cap /
Measuring Cup
APPLIANCE OVERVIEW
• Easy Start Guide
• User Manual
• Warranty Policy
BEFORE USE
Ensure to thoroughly clean and rinse all parts of the Blender (except the main
body) before rst use (refer to the Cleaning and Maintenance section of this user
manual for more details).
1. Inner Cap /
Measuring Cup
2. Jug Cover
3. Jug
4. Sealing Ring
5. Blade Holder
6. Jug Base
7. Ice Crushing Button
8. Blend Button
9. Main Body
10. Pulse Button
11. Speed Selector
1
2
3
4
5
7
8
9
10
11
6
5
D
E
F
G
A
B
C
ASSEMBLING YOUR BLENDER
STEP 1
Insert the Sealing Ring (D) into the inner rim
of the Blade Holder (E).
STEP 2
Insert the Blade Holder (with Sealing Ring)
into the Jug Base (F).
STEP 3
Mount the Jug (C) on top of the Jug Base
(F), then turn the Jug clockwise until it
securely locks into place.
STEP 4
Place the Jug Cover (B) on top of the Jug,
then insert its Inner Cap (A) in a clockwise
manner until it locks into the Jug Cover.
• Before assembling, ensure that your
Blender’s Speed Selector is in OFF
position.
• Ensure that all Blender components are
properly locked into place.
TIPS IN ASSEMBLING
YOUR BLENDER
6
USING THE BLENDER
TIPS IN USING YOUR BLENDER
• Before use, please check if the power voltage of your Blender correctly
corresponds to your home’s power supply.
• Before plugging in the power adapter to a power outlet, ensure that your
Blender’s Speed Selector is in OFF position.
• Ensure that the amount of ingredients / mixture inside the Jug does not
exceed the max level indicated on the Jug.
• Do not use boiling mixtures and/or run the appliance without any Jug
contents.
• To achieve best results in blending solid ingredients, slice the ingredients
into smaller pieces (2-3cm) and slowly add these into the Jug while using
the Pulse function.
• When mixing solid ingredients start in OFF mode rst with a small amount
of liquid. Gradually add more through the opening provided upon
removing the Inner Cap.
• During use, press the Jug Cover to ensure that the Jug is properly sealed.
• In stirring thick liquid ingredients, you may use the Pulse mode to prevent
the blades from getting stuck in the mixture.
STEP 1
Open the Jug cover and add in the ingredients that you want to blend into the
Jug. We highly recommend peeling and/or removing fruit cores and cutting
the fruits / vegetables into smaller pieces rst. It is also advisable to add a small
amount of water into the mixture to facilitate a smoother blending process.
STEP 2
Securely cover the Jug with the Jug Cover and insert the inner cap (if removed)
in a clockwise manner into the Jug Cover to completely seal the Jug.
STEP 3
Select the preferred function or turn the Speed Selector in a clockwise manner
to gradually increase the blending speed.
OPTIONAL FUNCTION BUTTONS (USE THIS WHILE APPLIANCE IS ON)
Ice
Crushing
If ice is present in your mixture (e.g. smoothies, blended
drinks), the Blender will operate at MAX speed and will stop
automatically once nished.
Blend
The Blender will operate for 60 seconds using the maximum
speed and would stop automatically.
Pulse
Press and hold to immediately accelerate blending speed.
7
CLEANING AND MAINTENANCE
STEP 4
If you want to add in extra ingredients, insert these through the Jug Cover’s
center opening. You may use the Inner cap to push the ingredients into
the jug.
STEP 5
Turn the Speed Selector to OFF position once the desired blending
consistency has been achieved. You may now remove the Jug from the
Main body and serve the blended food.
• Turn OFF and unplug its power adapter from the power outlet before
performing any cleaning, relocation, and/or maintenance.
• Do not immerse or expose your Blender’s main body and/or its power
cord to water or any kind of liquid substance. Simply use a slightly
damp cloth to clean your Blender’s external surface.
• Do not use any abrasive and/or aggressive cleaners in cleaning your
appliance.
• In assembling the appliance, handle each part carefully (e.g. Blender
Blades, Jug, etc.) to avoid injuries and/or appliance damage.
TIPS IN CLEANING YOUR BLENDER
QUICK CLEANING
Use your Blender’s Quick Cleaning feature if you plan to use your appliance
again in a different set of ingredients.
1. Dislodge the Jug from the Main Body.
2. Empty the Jug, ll it with water, then cover it using the Jug Cover.
3. Securely attach the Jug onto the Main Body again.
4. Use the Pulse function to rinse the Jug’s internal surface. Repeat this
step until the Jug is thoroughly rinsed.
5. Discard the Jug’s water. You may now use the Blender again.
THOROUGH CLEANING
To thoroughly clean your Blender after use.
1. Disassemble the Jug and its components from the main body. Ensure to
handle each component with care (e.g. Blender Blades) to avoid risks
of injury during cleaning.
2. You can wash all of the removed components except for the Main
body.
3. Dry each component using a soft dry cloth.
Copyright © 2016 Aztech Technologies Pte Ltd (CRN:199800635M ). All rights reserved.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Russell Hobbs rhbl1 User manual
-
Breville BBL200 User manual
-
Sage the 3X Bluicer User manual
-
Sunbeam MultiBlender PB7650 User manual
-
-
Kambrook KB600 User manual
-
-
Russell Hobbs RHMP750 User manual
-
-
Russell Hobbs rhbl3000 User manual
