Axler APC-A7S Quick start guide

Brand
Axler
Model
APC-A7S
Type
Quick start guide

Axler APC-A7S is a rugged, dedicated camera cage for Sony’s a7 and a7 II series cameras. It offers stability, protection, and a wide variety of options for mounting accessories to your camera. This camera cage is constructed with sturdy aluminum to precisely fit your Sony camera. It provides numerous 1/4ʺ and 3/8ʺ mounting points for accessories such as monitors, microphones, lights, or audio recorders. In addition, the camera cage is designed with three cold-shoe mounts for more attachment options. An ergonomic rosewood handle provides comfort when holding the camera, and the removable top handle makes lifting and moving a heavy rig easy.

Axler APC-A7S is a rugged, dedicated camera cage for Sony’s a7 and a7 II series cameras. It offers stability, protection, and a wide variety of options for mounting accessories to your camera. This camera cage is constructed with sturdy aluminum to precisely fit your Sony camera. It provides numerous 1/4ʺ and 3/8ʺ mounting points for accessories such as monitors, microphones, lights, or audio recorders. In addition, the camera cage is designed with three cold-shoe mounts for more attachment options. An ergonomic rosewood handle provides comfort when holding the camera, and the removable top handle makes lifting and moving a heavy rig easy.

www.AxlerSupports.com
APC-A7S
CAMERA CAGE
ONE-YEAR LIMITED WARRANTY
This Axler product is warranted to the original purchaser to be free
from defects in materials and workmanship under normal consumer
use for a period of one (1) year from the original purchase date or thirty
(30) days after replacement, whichever occurs later. The warranty
provider’s responsibility with respect to this limited warranty shall be
limited solely to repair or replacement, at the provider’s discretion, of
any product that fails during normal use of this product in its intended
manner and in its intended environment. Inoperability of the product or
part(s) shall be determined by the warranty provider. If the product has
been discontinued, the warranty provider reserves the right to replace
it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse,
neglect, accident, alteration, abuse, improper installation or
maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. This warranty provides you with specific legal rights, and
you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Axler Customer Service
Department to obtain a return merchandise authorization (“RMA”)
number, and return the defective product to Axler along with the RMA
number and proof of purchase. Shipment of the defective product is at
the purchaser’s own risk and expense.
For more information or to arrange service, visit axlersupports.com or
call Customer Service at 212-594-2353.
Product warranty is provided by the Gradus Group.
www.gradusgroup.com
Axler is a registered trademark of the Gradus Group.
© 2016 Gradus Group LLC. All Rights Reserved.
• Please read and follow these instructions, and keep this manual in a safe place.
• Handle the unit with care.
• Clean the unit with a soft, dry cloth.
• Use only parts provided by the manufacturer.
• Make sure that this product is intact and that there are no missing parts.
• To avoid damage to this product, be careful not to overtighten or improperly
thread any of the threaded fittings.
• Make sure everything is secure before proceeding.
• All images are for illustrative purposes only.
1. Main body
2. Top hand grip
3. Arc T key
4. Baseplate
5. 15 mm standard rods (×2)
6. Top hand grip connector
7. M4×14 screws (×2)
8. M4×8 screws (×2)
9. M4×6 screws (×3)
10. HDMI plug protector
11. Micro HDMI adapter cable
12. 1/4ʺ-20 camera locking screw
13. Hex key
OVERVIEW
PRECAUTIONS
QUICK-START
GUIDE
GG2
1
3
4
5
6
7 98
10
11
12
13
2
SPECIFICATIONS
Dimensions
(H × W × D)
Cage: 4ʺ × 6ʺ × 2.5ʺ (10.2 × 15.2 × 6.3 cm)
Handle: 3.25ʺ × 1ʺ × 6ʺ (8.2 × 2.5 × 15.2 cm)
Baseplate: 2.75ʺ × 4.25ʺ × 1.75ʺ
(7 × 10.8 × 4.4 cm)
Rod compatibility Rod size: 15 mm
Rod spacing: 60 mm
Mounting holes 1/4ʺ-20, 3/8ʺ-16
Weight (assembled
without camera)
2.3 lb. (1 kg)
Material Cage: Aluminum
Rods: Aluminum
Grip: Rosewood
Camera compatibility Sony a7, a7R, a7S, a7 II, a7R II, a7S II
www.AxlerSupports.com
APC-A7S
CAMERA CAGE
ONE-YEAR LIMITED WARRANTY
This Axler product is warranted to the original purchaser to be free
from defects in materials and workmanship under normal consumer
use for a period of one (1) year from the original purchase date or thirty
(30) days after replacement, whichever occurs later. The warranty
provider’s responsibility with respect to this limited warranty shall be
limited solely to repair or replacement, at the provider’s discretion, of
any product that fails during normal use of this product in its intended
manner and in its intended environment. Inoperability of the product or
part(s) shall be determined by the warranty provider. If the product has
been discontinued, the warranty provider reserves the right to replace
it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse,
neglect, accident, alteration, abuse, improper installation or
maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. This warranty provides you with specific legal rights, and
you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Axler Customer Service
Department to obtain a return merchandise authorization (“RMA”)
number, and return the defective product to Axler along with the RMA
number and proof of purchase. Shipment of the defective product is at
the purchaser’s own risk and expense.
For more information or to arrange service, visit axlersupports.com or
call Customer Service at 212-594-2353.
Product warranty is provided by the Gradus Group.
www.gradusgroup.com
Axler is a registered trademark of the Gradus Group.
© 2016 Gradus Group LLC. All Rights Reserved.
• Please read and follow these instructions, and keep this manual in a safe place.
• Handle the unit with care.
• Clean the unit with a soft, dry cloth.
• Use only parts provided by the manufacturer.
• Make sure that this product is intact and that there are no missing parts.
• To avoid damage to this product, be careful not to overtighten or improperly
thread any of the threaded fittings.
• Make sure everything is secure before proceeding.
• All images are for illustrative purposes only.
1. Main body
2. Top hand grip
3. Arc T key
4. Baseplate
5. 15 mm standard rods (×2)
6. Top hand grip connector
7. M4×14 screws (×2)
8. M4×8 screws (×2)
9. M4×6 screws (×3)
10. HDMI plug protector
11. Micro HDMI adapter cable
12. 1/4ʺ-20 camera locking screw
13. Hex key
OVERVIEW
PRECAUTIONS
QUICK-START
GUIDE
GG2
1
3
4
5
6
7 98
10
11
12
13
2
SPECIFICATIONS
Dimensions
(H × W × D)
Cage: 4ʺ × 6ʺ × 2.5ʺ (10.2 × 15.2 × 6.3 cm)
Handle: 3.25ʺ × 1ʺ × 6ʺ (8.2 × 2.5 × 15.2 cm)
Baseplate: 2.75ʺ × 4.25ʺ × 1.75ʺ
(7 × 10.8 × 4.4 cm)
Rod compatibility Rod size: 15 mm
Rod spacing: 60 mm
Mounting holes 1/4ʺ-20, 3/8ʺ-16
Weight (assembled
without camera)
2.3 lb. (1 kg)
Material Cage: Aluminum
Rods: Aluminum
Grip: Rosewood
Camera compatibility Sony a7, a7R, a7S, a7 II, a7R II, a7S II
ASSEMBLY INSTRUCTIONS
1. Attach the top hand grip to the top hand grip connector. (Fig. 1)
a. Align the three screw holes of the top hand grip connector with the
screw sockets on the top hand grip.
b. Insert the top hand grip and attach it by tightening all three M4×6
screws with the hex key.
2. Attach the top hand grip connector to the main body. (Fig. 2)
a. Align the two holes at the base of the top hand grip connector with
two of the sockets on the front of the main body (see note below).
b. Insert and tighten the two M4×8 screws with the hex key.
Note: There are three available sets of screw sockets to attach the top
hand grip connector to the main body. If the position of the top hand grip
needs to be changed to better balance the camera once it is attached to
the main body, remove the two M4×8 screws and select another pair of
screw sockets on the main body.
3. Attach the camera to the main body.
a. Turn the cage and top handle assembly upside down and fit the
camera into the cage. (Fig. 3)
b. Align the camera’s mounting socket with the camera locking screw
hole on the main body. (Fig. 4)
c. Use the 1/4ʺ-20 screw to attach the camera. To ensure the camera is
securely attached, tighten the screw with a screwdriver or a coin.
4. Attach the HDMI plug protector and micro HDMI cable.
a. Open the door to the HDMI port on the side of the camera.
b. Align the screw holes of the HDMI plug protector with the screw
sockets on the side of the main body, and attach the HDMI plug
protector by tightening the M4×14 screws with the hex key. (Fig. 5)
c. Insert the HDMI D (Micro) plug through the plug protector and into
the camera’s HDMI D (Micro) port. Secure the cable by tightening
the two plug protector screws.
d. Fit the HDMI plug through the gap in the plug protector and lock it
into place by tightening the plug protector screws. (Fig. 6)
ATTACHING THE RODS
1. Insert the two 15 mm rods into the baseplate holes and set the rods
at the desired position. (Fig. 7)
2. Tighten the locking knobs on both sides of the baseplate.
ATTACHING THE BASEPLATE
1. Loosen the locking screw on the baseplate and fit the quick-release
plate into the baseplate. (Fig. 8)
2. Lock the quick-release plate by tightening the locking screw.
Important! Make sure that the quick-release plate is seated entirely
inside the baseplate.
MOUNTING ON A TRIPOD
The baseplate is designed with 3/8ʺ-16 and 1/4ʺ-20 threaded mounting
sockets .
1. Remove the camera cage and camera assembly from the baseplate.
2. Align the appropriate mounting socket with the mounting stud of
the tripod's quick-release plate and screw it in until secure.
3. Attach the camera cage and camera assembly to the baseplate and
secure with the locking screw.
4. Mount the assembly to your tripod's locking plate.
THANK YOU FOR CHOOSING AXLER.
The Axler APC-A7S is a rugged, dedicated camera cage for Sony’s a7 and
a7 II series cameras. It offers stability, protection, and a wide variety of
options for mounting accessories to your camera.
This camera cage is constructed with sturdy aluminum to precisely fit
your Sony camera. It provides numerous 1/4ʺ and 3/8ʺ mounting points
for accessories such as monitors, microphones, lights, or audio recorders.
In addition, the camera cage is designed with three cold-shoe mounts
for more attachment options. An ergonomic rosewood handle provides
comfort when holding the camera, and the removable top handle makes
lifting and moving a heavy rig easy.
The APC-A7S gives you access to all of the features of your Sony camera.
The HDMI plug protector ensures that the HDMI connection will not come
loose during shooting, and will securely hold the plug in place to prevent
damage to the camera’s HDMI port.
The cage comes with a quick-release plate for easy attachment to
the baseplate. And the baseplate is designed with 1/4"-20 and 3/8"-16
tripod mounting options. The baseplate accommodates two 15 mm rods
(included) to allow for the addition of follow focus or matte box systems
as well as other rail-mounted accessories.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 8
Fig. 7
Fig. 6
www.AxlerSupports.com
APC-A7S
CAMERA CAGE
ONE-YEAR LIMITED WARRANTY
This Axler product is warranted to the original purchaser to be free
from defects in materials and workmanship under normal consumer
use for a period of one (1) year from the original purchase date or thirty
(30) days after replacement, whichever occurs later. The warranty
provider’s responsibility with respect to this limited warranty shall be
limited solely to repair or replacement, at the provider’s discretion, of
any product that fails during normal use of this product in its intended
manner and in its intended environment. Inoperability of the product or
part(s) shall be determined by the warranty provider. If the product has
been discontinued, the warranty provider reserves the right to replace
it with a model of equivalent quality and function.
This warranty does not cover damage or defect caused by misuse,
neglect, accident, alteration, abuse, improper installation or
maintenance. EXCEPT AS PROVIDED HEREIN, THE WARRANTY
PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY
IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. This warranty provides you with specific legal rights, and
you may also have additional rights that vary from state to state.
To obtain warranty coverage, contact the Axler Customer Service
Department to obtain a return merchandise authorization (“RMA”)
number, and return the defective product to Axler along with the RMA
number and proof of purchase. Shipment of the defective product is at
the purchaser’s own risk and expense.
For more information or to arrange service, visit axlersupports.com or
call Customer Service at 212-594-2353.
Product warranty is provided by the Gradus Group.
www.gradusgroup.com
Axler is a registered trademark of the Gradus Group.
© 2016 Gradus Group LLC. All Rights Reserved.
• Please read and follow these instructions, and keep this manual in a safe place.
• Handle the unit with care.
• Clean the unit with a soft, dry cloth.
• Use only parts provided by the manufacturer.
• Make sure that this product is intact and that there are no missing parts.
• To avoid damage to this product, be careful not to overtighten or improperly
thread any of the threaded fittings.
• Make sure everything is secure before proceeding.
• All images are for illustrative purposes only.
1. Main body
2. Top hand grip
3. Arc T key
4. Baseplate
5. 15 mm standard rods (×2)
6. Top hand grip connector
7. M4×14 screws (×2)
8. M4×8 screws (×2)
9. M4×6 screws (×3)
10. HDMI plug protector
11. Micro HDMI adapter cable
12. 1/4ʺ-20 camera locking screw
13. Hex key
OVERVIEW
PRECAUTIONS
QUICK-START
GUIDE
GG2
1
3
4
5
6
7 98
10
11
12
13
2
SPECIFICATIONS
Dimensions
(H × W × D)
Cage: 4ʺ × 6ʺ × 2.5ʺ (10.2 × 15.2 × 6.3 cm)
Handle: 3.25ʺ × 1ʺ × 6ʺ (8.2 × 2.5 × 15.2 cm)
Baseplate: 2.75ʺ × 4.25ʺ × 1.75ʺ
(7 × 10.8 × 4.4 cm)
Rod compatibility Rod size: 15 mm
Rod spacing: 60 mm
Mounting holes 1/4ʺ-20, 3/8ʺ-16
Weight (assembled
without camera)
2.3 lb. (1 kg)
Material Cage: Aluminum
Rods: Aluminum
Grip: Rosewood
Camera compatibility Sony a7, a7R, a7S, a7 II, a7R II, a7S II
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Axler APC-A7S Quick start guide

Brand
Axler
Model
APC-A7S
Type
Quick start guide

Axler APC-A7S is a rugged, dedicated camera cage for Sony’s a7 and a7 II series cameras. It offers stability, protection, and a wide variety of options for mounting accessories to your camera. This camera cage is constructed with sturdy aluminum to precisely fit your Sony camera. It provides numerous 1/4ʺ and 3/8ʺ mounting points for accessories such as monitors, microphones, lights, or audio recorders. In addition, the camera cage is designed with three cold-shoe mounts for more attachment options. An ergonomic rosewood handle provides comfort when holding the camera, and the removable top handle makes lifting and moving a heavy rig easy.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents