CAME BK-221 Installation guide

BK-221

BK SERIES

INSTALLATION MANUAL

AUTOMATION

FOR SLIDING GATES

English

EN

WARNING!

Important instructions for the safety of people:

READ CAREFULLY!

Foreword

• Use of the products must be restricted to its intended use

(i.e. that for which it was expressly built for). Any other use is

to be considered dangerous. Came Cancelli Automatici S.p.A.

is not liable for any damage resulting from improper, wrongful

or unreasonable use • Keep these warnings with the installa-

tion and use manuals issued with the automated system.

Before installing

(preliminary check: in case of a negative

outcome, do not proceed before having

complied with the safety obligations)

• Make sure that the parts you intend to automate are in

good working order, and that they are properly balanced

and aligned. Also, make sure that proper mechanical stops

are already in place • If the operator will be installed at a

height of less than 2.5 m from the ground or other access

level, check whether you will need any protections and/or

warnings • Any gate leaves, ﬁ tted with pedestrian entrances,

onto which you will install an operator, must have a blocking

mechanism when the gate is in motion • Make sure that the

opening of the automated gate is not an entrapment hazard

as regards any surrounding ﬁ xed parts • Do not mount the

operator upside down or onto any elements that may fold

under its weight. If needed, add suitable reinforcements at

the points where it is secured • Do not install onto gates on

either an upward or downward slope (i.e. that are not on ﬂ at,

level ground) • Check that any lawn watering devices will not

wet the gearmotor from the bottom up.

Installation

• Carefully section off the entire site to prevent unauthorised

access, especially by minors and children • Be careful when

handling operators that weigh more than 20 Kg (see installa-

tion manual). In such cases, employ proper weight handling

safety equipment • All opening commands (e.g. buttons, key

selectors, magnetic detectors, etc.) must be installed at least

1.85 m from the gate’s area of operation perimeter - or where

they cannot be reached from the outside of the gate. Also,

the direct commands (e.g. push button, or proximity devices,

etc.) must be installed at a height of at least 1.5 m and must

not be accessible to the public • All ‘maintained action’ com-

mands, must be placed where the moving gate leaves, transit

areas and driveways are completely visible • If missing, ap-

ply a permanent label that shows the position of the release

mechanism • Before delivering to the client, verify that the

system is EN 12453 (impact test) standard compliant. Make

sure that the operator has been properly adjusted and that the

safety and protection devices, as well as the manual release

are working properly • Where necessary and in plain sight,

apply the Warning Sings (e.g. gate plate).

Special instructions and

advice for users

• Keep the gate’s area of operation clean and clear of any

obstacles. Trim any vegetation that may interfere with the

photocells • Do not allow children to play with the ﬁ xed com-

mand devices, or in the gate’s area of operation. Keep any

remote control devices (i.e. transmitters) away from the chil-

dren as well • Frequently check the system, to see whether

any anomalies or signs of wear and tear appear on the moving

parts, on the component parts, on the securing points, on the

cables and any accessible connections. Keep any joints (i.e.

hinges) lubricated and clean, and do the same where fric-

tion may occur (i.e. slide rails) • Perform functional tests on

photocells and sensitive edges, every six months. Keep glass

panels constantly clean (use a slightly water-moistened cloth;

do not use solvents or any other chemical products) • If the

system requires repairs or modiﬁ cations, release the operator

and do not use it until safety conditions have been restored

• Cut off the power supply before releasing the operator for

manual openings. See instructions • Users are FORBIDDEN

to carry out ANY ACTIONS THAT THEY HAVE NOT BEEN

EXPRESSLY ASKED TO DO OR SO INDICATED in the manu-

als. Any repairs, modiﬁ cations to the settings and extraor-

dinary maintenance MUST BE DONE BY THE TECHNICAL

ASSISTANCE STAFF • On the periodic maintenance log, note

down the checks you have done.

Special instructions and

advice for all

• Avoid working near the hinges or moving mechanical parts

• Stay clear of the gate’s area of operation when in motion •

Do not resist the direction of movement of the gate; this may

present a safety hazard • At all times be extremely careful

about dangerous points that must be indicated by proper

pictograms and/or black and yellow stripes • When using

a selector or command in ‘maintained action’ mode, keep

checking that there are no people in the area of operation of

the moving parts. Do this until you release the command •

The gate may move at any time without warning • Always cut

the power when cleaning performing maintenance.

THIS PAGE LEFT INTENTIONALLY BLANK

#

#

Pag.

2

- Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

4.1 Gearmotor

The BK-221 gearmotor is designed and built by CAME CANCELLI AUTOMATICI S.p.A. and it meets the safety standards in force.

The case consists partly of cast aluminium, inside of which operates the non-reversible electromechanical gearmotor, and partly of

a covering in ABS plastic inside of which is an electronic card and the transformer.

The BK-221 gearmotor may be supplied with complementary accessories such as:

001 R001 - Lock cylinder with DIN keys;

001 BSF - Braking device for gates installed on a sloping surface;

001 B4353 - Chain transmission device;

009 CGZ - Galvanized steel 22 x 22 module 4 rack;

009 CGZS - Galvanized steel 30 x 8 module 4 rack with fastening screws, holes and supports;

009 CCT - Simple 1/2” chain;

009 CGIU - 1/2” chain joint.

Important! Check that the safety equipment and accessories are CAME originals; this is a guarantee that also makes the system

easy to set up and upkeep.

4 Description

2.1 Destination

1 Legend

This symbol indicates sections to be read with particular care.

This symbol indicates sections concernig safety

This symbol indicates notes to communicate to users.

The company CAME cancelli automatici is ISO 9001 quality certiﬁ ed; it has also obtained the ISO 14001 environmental safeguarding

certiﬁ cation. CAME engineers and manufactures all of its products in Italy.

This product complies with the following legislation: see declaration of compliance.

2 Destination and limits of use

The BK-221 gearmotor is designed to automate sliding gates for residential and condominium complexes.

The use of this product for purposes other than the one intended and installation carried out in a manner other than as

instructed in this technical manual are prohibited.

3 Standard followed

“IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION”

“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”

“THIS MANUAL IS ONLY FOR PROFESSIONAL INSTALLERS OR QUALIFIED PERSONS”

2.2 Limits of use

Maximum gate weight 2200 kg with maximum length of 20 meters.

4.2 Technical information

GEARMOTOR

Power supply: 230 V AC 50 / 60 Hz

Motor power supply: 230 V AC 50 / 60 Hz

Max. absorption: 5.1 A

Rated power: 580 W

Reduction ratio: 1/31

Push: 1500 N

Max. speed: 10,5 m/min

Operation intermittence: 50%

Protection level: IP54

Insulation class: I

Engine thermoprotection: 150° C

Weight: 21 kg

CAME

360

105

15

22 max.

182.5

142.5

170

255

106

7

1

3

2

4

5

6

3

7

6

1

5

4

8

9

10

2

Pag.

3

-

Manual code

:

119BV25

119 BV25 ver.

1.1

1.1 06/2011

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

4.4 Overall dimensions

Measurements in mm

4.3 Parts description

GEARMOTOR UNIT

Gearmotor1.

Board cover support2.

End-stop ﬂ aps3.

ZBK10 basic control board4.

Electric board front cover5.

Release door6.

Base plate7.

Securing screws8.

Plates for securing screws9.

Nuts 10.

ACCESSORIES

R001 - Cylinder lock with DIN keys1.

BSF - Braking device2.

B4353 - Chain transmission device3.

CCT - Simple 1/2” chain4.

CGIU - 1/2” chain joint5.

CGZ - Galvanized steel 22 x 22 module 4 rack6.

CGZS - Galvanized steel 30 x 8 module 4 rack with fastening 7.

screws, holes and supports

Pag.

4

- Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

5.1 Preliminary checks

Before actually installing the gate operator, your are required to:

• Check that the leaf is rigid and compact and that the rollers are in good working order and properly greased;

• The gate track must be firmly set into the ground, above ground along its entire length and free of any foreign objects (debris)

that may hamper the gate’s movement;

• The top non-pinch rollers must not cause any friction;

• See to installing physical stops at fully-opened and fully-closed positions and the power supply line trench as per the standard

installation;

• Make sure that the spot were the operator is mounted is located in an area that is protects it from any impacts, and that the

mounting surface be solid;

• See to installing a suitable all-pole disconnector switch, with power isolation contacts more than 3mm apart from each other;

• Connections inside of the casing made to provide continuity to the protection circuit are allowed, as long as they have additional

isolation compared to other internal conductive parts;

• Set up suitable tubing and trenching to allow for electrical cables to pass, making sure they are free from any potential mechanical

damage.

Only expert, qualified personnel must carry out the installation, in full compliance with the applicable law.

5 Installation

5.2 Tools and materials

Make sure you have all the tools and materials handy, to carry out the installation in total safety, according to the laws in-force.

Below is a drawing of the tools you will need to install the operator.

N.B.: An evaluation of the size of the cables with lengths other than the data in the table must be made based on the e ective

absorption of the connected devices, according to the instructions indicated by the CEI EN 60204-1 standards.

For connections that require several loads on the same line (sequential), the size given on the table must be re-evaluated based on

actual absorption and distances.

5.3 Cable list and minimun thickness

Connections Type of cable

Length of cable

1 < 10 m

Length of cable

10 < 20 m

Length of cable

20 < 30 m

120V-230V 2F power supply

FROR CEI

20-22

CEI EN

50267-2-1

3G x 1,5 mm

2

3G x 2,5 mm

2

3G x 4 mm

2

230V flashing lamp 2 x 0,5 mm

2

2 x 1 mm

2

2 x 1,5 mm

2

Photoelectric cells TX 2 x 0,5 mm

2

2 x 0.5 mm

2

2 x 0,5 mm

2

Photoelectric cells RX 4 x 0,5 mm

2

4 x 0,5 mm

2

4 x 0,5 mm

2

24V power supply accessory 2 x 0,5 mm

2

2 x 0,5 mm

2

2 x 1 mm

2

Control button 2 x 0,5 mm

2

2 x 0,5 mm

2

2 x 0,5 mm

2

Antenna connection RG58 max. 50 m

MM

MM

MM

6

5

9

3

1

2

4

9

10

11

7

6

5

9

3

1

2

4

12

11

1010

8

4

CAME

Pag.

5

-

Manual code

:

119BV25

119 BV25 ver.

1.1

1.1 06/2011

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

BK-221 unit 1.

Control board incorporated2.

Radio receiver3.

Limit-switch tabs4.

Rack5.

Key-operated selector switch6.

Flashing light indicating door movement7.

Antenna8.

Safety photocells9.

Photocell column10.

Closure stop11.

The following applications are only examples, as the space required for unit installation and the accessories vary depending

on dimensions and therefore it is up to the installer to select the best solution.

Install the screws in the anchor plate and fasten them with a nut, then bend the preformed clamps downwards.

Construct a cement foundation that is large enough to accomodate the gear motor (it is a good idea to protrude 50 mm. from the

ground). When pouring the foundation, embed the gear motor anchor plate and the relative clamps in the cement.

The anchor bolts should be embedded in the concrete in the positions indicated; the drive unit is then attached to this bots. The anchor

plate must be perfectly level and absolutly clean; the bolts threads must be completly exposed.

N.B.: The ﬂ exible tubes for the electrical wiring must be embedded in the base and protude in the correct position.

5.4 Motor to base anchorage

Fixing plate / Anchor stays

Cables

Concrete

base

Rack-limit

Gate wing

Wall

CAME

5÷10 mm.

Pag.

6

- Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Horizontal adjustment

and unit anchorage

Vertical adjustment and

unit leveling

Cable entrances

Afstand tussen tandwiel en tandlat

Module M6 = 1,5 mm speling

During the initial phase of installation, the feet should protrude by 5-10 mm. in order to allow for alignment, anchorage of the

rack and further adjustments.

Perfect alignment with the guide rail is made possible by the (paten-ted) built-in regulation system, which consists of:

- slots for horizontal adjustment;

- threaded steel feet for vertical adjustment and levelling;

- plates and bolts for anchorage to the base.

5.5 Unit installation

5.6 Attaching the rack/limit

Attach the rack to the gate as described below:

- Release the gearmotor (parag. 5.8);

- position the rack on the pinion of the gearmotor and slide the gate manually in order to attach the rack along its entire length;

- when the rack is attached to the gate, adjust the feet using a screwdriver until the play between the pinion and the rack is correct

(1÷2 mm.).

N.B.: This position ensures that the weight of the gate does not rest on the gearmotor.

- If the rack is already attached, proceed directly to the adju-stment of the rack/pinion coupling.

- when the necessary adjustment have been completed, fasten the unit in position by tightening the two anchor bolts.

#!-%

!

"

#!-%

Pag.

7

-

Manual code

:

119BV25

119 BV25 ver.

1.1

1.1 06/2011

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

BLOCK

RELEASE

To open the access door, insert the key A, push down and rotate clockwise. Then release the ratio motor by using key B on the

threelobed pin and turning it in the direction indicated.

To re-lock the reduction gear, turn key B in the direction indicated until it will move no further, without forcing it: the three-sid ed

pin will settle into place at the ﬁ rst movement.

5.7 Attaching the switch tabs

Position the limit-switch tabs (whose positions determine the limits of gate travel) on the rack.

Note: do not allow the gate to strike the mechanical stops in the open or closed positions.

5.8 Manual release of the gearmotor

ATTENTION: the opening of the

unblock panel arrests the motor.

LN

L1T L2T

CT VS VF

U VWE

EX

26V 17V

01011

TS 1 2 3 3P 4 5 7 2 CX CY C7 C8 2 A B + E D FC FA F

4

10

11

6

812 13

9 1

7

5 2 3

Pag.

8

- Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

FUSE TABLE ZBK10

To protect: fuse:

Control board (line) 8 A-F

Accessories 1.6 A-F

Command devices 1 A-F

TECHNICAL INFORMATION

Power supply 230 V - 50 / 60 Hz

Absorption at rest 110 mA

Maximum power for 24V accessories 37 W

6 Control board

6.1 General description

6.2 Main components

Use 230V A.C. to power the electronic card using the L-N terminals, at a max 50/60Hz frequency.

Use 24V to power the command devices and accessories. Careful! The accessories cannot exceed 37W of overall power.

All connections are protected by quick-fuses – see table.

The input and output contact functions, the timing settings and users’ management, are set and viewed on the display, which is run by

software.

Warning! Before acting on the machinery, cut o the main power supply and disconnect any emergency batteries.

Display1.

Card fuse2.

Accessory fuse3.

Line fuse4.

AF card coupling for remote control5.

RSE card coupling for paired connections6.

230 V-power signalling LED7.

Connecting terminal board8.

Programming buttons9.

Display lighting adjustment trimmer10.

Memory roll board connector11.

Power supply terminals12.

Antenna terminals13.

COM

NC

COM

Pag.

9

-

Manual code

:

119BV25

119 BV25 ver.

1.1

1.1 06/2011

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

6.3 Electrical connections

230V (A.C.) motor

with encoder

Closing microswitch

Gearmotor, endstop and encoder

Modifications to the electrical connections for right-hand installations

Invert the gearmotor (U-V) and (FA-FC) endstop phases.

Opening microswitch

Description of the standard electrical connections for left-hand installations

Black

Red

Terminals for powering the following accessories:

- 24V A.C. Maximum allowed power: 37W

Power supply for accessories

230V (A.C.) Power, 50/60Hz

frequency

Cable lug with bolt and washer for connecting to earth.

Orange

Red

White

Red

White

Capacitor

Pag.

10

10 - Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Open-gate status light

(contact range: 24V – 3W max)

- Signal that gate is open; turns o when

gate is closed.

Movement ﬂ ashing light

(Contact range: 230V – 25W max).

- Flashes during the gate’s opening and

closing phases.

Command and control devices

Warning devices

Cycle lamp (contact rating: 230V – 60W max.).

- It lights up the driving area and stays on from the

moment the gate begins to open until it is fully closed

(including the automatic closing time). If automatic

closing is not activated, the lamp stays on only during

movement or for a set time of 5 minutes if used as a

courtesy lamp.

Courtesy lamp (Contact output: 230 V - 60 W max.)

- Auxiliary connection for suitably positioned external

lamp to increase lighting of the steering area. It

remain lit for a ﬁ xed time of 5 minutes.

Stop button (N.C. contact) - Gate stop button. Excludes automatic

closing. For motion to resume, press the command button or the

remote control button.

N.B.: if contact is unused, select OFF on the “FUNCTIONS” menu.

Key selector and/or opening button (N.O. contact) -

Gate opening command.

Key selector and/or commands button (N.O.

contact) Commands for opening and closing the gate

– pressing the button or turning the key-switch, inverts

the gate’s movement or stops it depending on how it is

set on the 2-7 command in the “FUNCTIONS” menu

Key selector and/or partial opening button (N.O.

contact) - Partial gate opening for pedestrian access.

Key selector and/or closing button (N.O. contact) -

Gate closing command.

Antenna with RG58

cable for the remote

control.

or in alternative

RX

TX

RX TX



./ # .#





#./.#

6 6

.#

./

#

6

#./.#

Pag.

11

11 -

Manual code

:

119BV25

119 BV25 ver.

1.1

1.1 06/2011

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Safety devices

Conﬁ gure either (N.C.) contacts CX or CY, input for

safety devices such as photocells, that comply with EN

12978 standards. See CX or CY input functions in:

- C1 «re-open during closing phase», When the gate

leaf is closing, opening the contact triggers the inversion

of the direction of movement until the gate leaf is fully

open.

- C2 «re-close during opening phase», When gate is

opening, if the contact is opened it triggers an inversion

of the direction until gate is fully closed;

- C3 «partial stop», gate stops if moving and

automatically shuts (if this functions has been selected);

- C4 «stand-by Obstacle», Halts the moving gate leaves

causing them to start moving again once obstacle is

removed.

- Deactivated, if the contact is unused.

DIR photocells

DOC photocells

Conﬁ gure either (N.C.) contacts C7 or C8, input

for EN 12978 compliant safety devices such as

sensitive edges. See C7 or C8 input functions in:

- C7 «re-open during closing phase», - During

gate closing, opening the contact causes inversion

of movement until gate is fully open;

- C8 «re-close during opening phase», - During

gate opening, opening the contact causes inversion

of movement until gate is fully close;

OFF, is the contact is unused

DF with DFI connections monitor card





./

.#

#









&53)"),%M!

48



48 

  48

#







.#





(DOC)

(DIR)

0

17

24

FRENO

1

2

3

4

SPUNTO

LN

L1T L2T

CT VS VF

U VWE

EX

26V 17V

01011

TS

Pag.

12

12 - Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

6.4 Electrical connection to operate the photocells’ safety test

At each open/close command, the card check the photocells’ e ciency.

Any problems with the photocells will cause the (PROG) Led to ﬂ ash on the

electronic card, which cancels any commands from the radio transmitter or

push-button.

Electrical connection to operate the photocells’ safety test:

- The transmitter and receiver, must be connected as shown in the diagram;

- from the functions menu, select “safety tests” and select either CX or CY input/s to activate the test.

6.5 Motor torque limiter

To vary the motor torque, move the shown

faston (the one with the black wire) to one of the

4 positions: 1 min – 4 max.

WWW.CAME.IT

ZBK10

Pag.

13

13 -

Manual code

:

119BV25

119 BV25 ver.

1.1

1.1 06/2011

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

N.B.: when the menu is active, the system cannot be used.

The ENTER key is for:

- entering the menu

- confirming and memorising set values

The ESC key is for:

- exiting the menu

- cancelling modifications

The <> keys are for:

- shifting from one menu item to another

- increase or decrease values

the <...> symbols on the display are for:

- pointing out the currently, selected item

To enter the menu, keep the

ENTER key pressed for at least one

second.

To select a menu item,

mode using the greater

than-lesser than keys...

...then press ENTER

also use the greater

than-lesser than keys

for the “sub-menus”...

If the <> are on the TIME

function, you may modify the

value.

To increase or reduce

values, use the greater than-

lesser than keys...

...then press ENTER to confirm...

...to exit the menu, wait 30

seconds, or press ESC, until start

screen is displayed.

7 Programming

LANGUAGE

English

Þß

LANGUAGE

English

Þß

FUNCTIONS

English

Þß

TIMING ADJ.

Þß

A.C.T.

90s

Þß

Cycle Time

90s

Þß

Cycle Time

90s

Þß

Cycle Time

100s

Þß

LANGUAGE

Þß

7.1 Description of display commands

7.2 Browsing the menu

ENTER

>

ENTER

>

ENTER

>

ENTER

>>

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

ENTER

>

Pag.

14

14 - Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

7.3 Menu structure

< LANGUAGE >

< INFO >

< A.C.T. >

< Cycle Time >

< New User >

< Modify User >

< Remove Usr. >

< Backup data >

< Slowdown >

< Partial op. >

< Encoder >

< NET address >

< Startup Msg >

< 10s >

< FUNCTIONS >

< 11s >

< 90s >

< 91s >

< 5s >

< 6s >

< 5s >

< 6s >

<2-7 Func>

< RADIO USRS >

Do you conf.?

< No >

< FW Version >

ver. 1.0

16480

Reading

ooooooo

•••

Writin g

ooooooo

•••

n.001 In use

n.002 Empty

n.001 In use

n.002 Empty

See detailed

description on

chap. 7.14

< 10% >

< 11% >

< 10% >

< 11% >

< Disabled >

< Master >

< Slave >

WWW.CAME.IT

ZBK10

<

ON

>

<

OFF

>

<

-oooooooo+

>

•

<

-oooooooo+

>

•

<

-oooo+

>

•

<

-oooo+

>

•

Do you conf.?

< Yes >

ENTER

>

>>

>

>>

>

Pag.

15

15 -

Manual code

:

119BV25

119 BV25 ver.

1.1

1.1 06/2011

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

< ON >

< OFF >

<Op.-Stop-Cl.>

< Disabled > < C1 >

< C2 >< C3 >< C4 >

< Disable > <Enabled on CX>

< Autom.Clos. >

< 2-7 Command >

< Preflash >

<Maint. Act. Cl.>

< CY Input >

< C7 Input >

< C8 Input >

< STOP (1) >

< Safety test >

< Lamp Output >

< CX Input >

< ON >

< OFF >

< ON >

< OFF >

< ON >

< OFF >

< Disabled > < C1 >

< C2 >< C3 >< C4 >

< ON >

< OFF >

< ON >

< OFF >

< ON >

< OFF >

< Cycle >

< Courtesy >< Fl. light >

< Obst. Detect >

< ON >

< OFF >

>

X 2

Pag.

16

16 - Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

7.4 Main menu

LANGUAGE

English

FUNCTIONS TIMING ADJ.

RADIO USRSADJUSTMENTS

INFO

Press ENTER for

1 second

7.5 Language menu

Select language: selects among the languages displayed.

< LANGUAGE >

English

LANGUAGE

< English >

LANGUAGE

< Francais >

LANGUAGE

< Deutsch >

LANGUAGE

< Espanol >

LANGUAGE

< Italiano >

FUNCTIONS

TIMING ADJ.

IMING ADJ

RADIO USRS

ADIO USRS

ADJUSTMENTS

DJUSTMENT

7.6 Functions menu

< Autom.Clos. >

ON

Autom.Clos.

< ON >

Autom.Clos.

< OFF >

Automatic Closing: activates or deactivates the automatic closing function.

The automatic closing timer activates at each opening endpoint. The predetermined time may be adjusted, and is in any case

dependent on any safety devices that may activate; and it does not activate after a total safety “stop” or during a power outage.

2-7 Command: sets the sequential command.

“Open-close” or “open-stop-close-stop” function with button [2-7] and radio transmitter (when radio-frequency card is inserted)

< 2-7 Command >

Op.-Stop-Cl.

2-7 Command

< Op.-Stop-Cl. >

2-7 Command

< Open Close >

INFO

<

LANGUAGE

>

English

h

FUNCTIONS

TIMING ADJ.

IMING ADJ

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

<

LANGUAGE

>

English

h

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

X 2

X 3

X 2

X 4

X 5

Pag.

17

17 -

Manual code

:

119BV25

119 BV25 ver.

1.1

1.1 06/2011

The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

Pre-flashing: after an opening or closing command, the ﬂ ashing light, connected to E-EX, starts ﬂ ashing before the gate begins its run

(to set the time, see “Pre-ﬂ ashing timing” from the Adjust Timings menu

< Preflash >

OFF

Preflash

< OFF >

Preflash

< ON >

Maintained action: The gate works by keeping the button pressed (button 2-3 for opening, button 2-4 for closing, or if set to the “On Closing”

function, only with button 2-4.

Closing maintained action: the gate closes by keeping the button pressed (only for the 2-4 closing button).

CX input: N.C. safety contact input, lets you pair up the following functions: C1 (re-opening during closing), C2 (re-closing during opening), C3

(partial stop), C4 (obstacle stall), or, deactivated

< CX Input >

Disabled

CX Input

< Disabled >

CX Input

< C1 >

CX Input

< C2 >

CX Input

< C3 >

CX Input

< C4 >

Maintained Act

< OFF >

OFF

Maintained Act

< ON >

Maint.Act. Cl.

< OFF >

< Maint.Act. Cl. >

OFF

Maint.Act. Cl.

< ON >

< LANGUAGE >

LANGUA

English

h

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

<

LANGUAGE

>

English

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

< LANGUAGE >

LANGUAG

English

h

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

< LANGUAGE >

ANGUA

English

h

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

X 2

X 8

X 2

X 6

X 2

X 7

X 2

X 9

Pag.

18

18 - Manual code:

119BV25

119 BV25 ver.

1.1

1.1 06/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.

ENGLISH

CY input: N.C. safety contact input, lets you pair up the following functions: C1 (re-opening during closing), C2 (re-closing during opening), C3

(partial stop), C4 (obstacle stall), or, deactivated

C7 input: N.C. safety contact input (re-opening when closing). This input is for EN 12978-compliant safety devices, like sensitive edges. When

the gate is closing, the open contact triggers an inversion in the gate’s movement until it is fully opened.

C8 input: N.C. safety contact input (re-closing during opening). This input is for EN 12978-compliant safety devices, like sensitive edges. When

the gate is opening, the open contact triggers an inversion in the gate’s movement until it is fully closed.

C8 Input

< OFF >

< C8 Input >

OFF

C8 Input

< ON >

< CY Input >

Disabled

CY Input

< Disabled >

CY Input

< C1 >

CY Input

< C2 >

CY Input

< C3 >

CY Input

< C4 >

C7 Input

< OFF >

< C7 Input >

OFF

C7 Input

< ON >

STOP (1)

< ON >

< STOP (1) >

OFF

STOP (1)

< OFF >

<

LANGUAGE

>

English

h

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

< LANGUAGE >

ANGUA

English

h

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

<

LANGUAGE

>

English

h

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

<

LANGUAGE

>

English

FUNCTIONS

TIMING ADJ.

TIMING AD

RADIO USRS

RADIO USR

ADJUSTMENTS

DJUSTMEN

INFO

STOP (1): this function stops the gate and consequently excludes any automatic closing cycle; for movement to resume, you need to use

the keypad or transmitter. Insert safety device on [1-2]; is unused, select “OFF” and confirm with ENTER.

Page is loading ...

CAME BK-221 Installation guide

CAME BK-221 Installation guide

Related papers

Other documents