CAME BK-221 Installation guide

Category
Gate Opener
Type
Installation guide
BK-221
BK SERIES
INSTALLATION MANUAL
AUTOMATION
FOR SLIDING GATES
English
EN
#
#
Pag.
2
- Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
4.1 Gearmotor
The BK-221 gearmotor is designed and built by CAME CANCELLI AUTOMATICI S.p.A. and it meets the safety standards in force.
The case consists partly of cast aluminium, inside of which operates the non-reversible electromechanical gearmotor, and partly of
a covering in ABS plastic inside of which is an electronic card and the transformer.
The BK-221 gearmotor may be supplied with complementary accessories such as:
001 R001 - Lock cylinder with DIN keys;
001 BSF - Braking device for gates installed on a sloping surface;
001 B4353 - Chain transmission device;
009 CGZ - Galvanized steel 22 x 22 module 4 rack;
009 CGZS - Galvanized steel 30 x 8 module 4 rack with fastening screws, holes and supports;
009 CCT - Simple 1/2” chain;
009 CGIU - 1/2” chain joint.
Important! Check that the safety equipment and accessories are CAME originals; this is a guarantee that also makes the system
easy to set up and upkeep.
4 Description
2.1 Destination
1 Legend
This symbol indicates sections to be read with particular care.
This symbol indicates sections concernig safety
This symbol indicates notes to communicate to users.
The company CAME cancelli automatici is ISO 9001 quality certifi ed; it has also obtained the ISO 14001 environmental safeguarding
certifi cation. CAME engineers and manufactures all of its products in Italy.
This product complies with the following legislation: see declaration of compliance.
2 Destination and limits of use
The BK-221 gearmotor is designed to automate sliding gates for residential and condominium complexes.
The use of this product for purposes other than the one intended and installation carried out in a manner other than as
instructed in this technical manual are prohibited.
3 Standard followed
“IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION”
“CAUTION: IMPROPER INSTALLATION MAY CAUSE SERIOUS DAMAGE, FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY”
“THIS MANUAL IS ONLY FOR PROFESSIONAL INSTALLERS OR QUALIFIED PERSONS”
2.2 Limits of use
Maximum gate weight 2200 kg with maximum length of 20 meters.
4.2 Technical information
GEARMOTOR
Power supply: 230 V AC 50 / 60 Hz
Motor power supply: 230 V AC 50 / 60 Hz
Max. absorption: 5.1 A
Rated power: 580 W
Reduction ratio: 1/31
Push: 1500 N
Max. speed: 10,5 m/min
Operation intermittence: 50%
Protection level: IP54
Insulation class: I
Engine thermoprotection: 150° C
Weight: 21 kg
CAME
360
105
15
22 max.
182.5
142.5
170
255
106
7
1
3
2
4
5
6
3
7
6
1
5
4
8
9
10
2
Pag.
3
-
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
4.4 Overall dimensions
Measurements in mm
4.3 Parts description
GEARMOTOR UNIT
Gearmotor1.
Board cover support2.
End-stop fl aps3.
ZBK10 basic control board4.
Electric board front cover5.
Release door6.
Base plate7.
Securing screws8.
Plates for securing screws9.
Nuts 10.
ACCESSORIES
R001 - Cylinder lock with DIN keys1.
BSF - Braking device2.
B4353 - Chain transmission device3.
CCT - Simple 1/2” chain4.
CGIU - 1/2” chain joint5.
CGZ - Galvanized steel 22 x 22 module 4 rack6.
CGZS - Galvanized steel 30 x 8 module 4 rack with fastening 7.
screws, holes and supports
Pag.
4
- Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
5.1 Preliminary checks
Before actually installing the gate operator, your are required to:
• Check that the leaf is rigid and compact and that the rollers are in good working order and properly greased;
• The gate track must be firmly set into the ground, above ground along its entire length and free of any foreign objects (debris)
that may hamper the gate’s movement;
• The top non-pinch rollers must not cause any friction;
• See to installing physical stops at fully-opened and fully-closed positions and the power supply line trench as per the standard
installation;
Make sure that the spot were the operator is mounted is located in an area that is protects it from any impacts, and that the
mounting surface be solid;
• See to installing a suitable all-pole disconnector switch, with power isolation contacts more than 3mm apart from each other;
• Connections inside of the casing made to provide continuity to the protection circuit are allowed, as long as they have additional
isolation compared to other internal conductive parts;
• Set up suitable tubing and trenching to allow for electrical cables to pass, making sure they are free from any potential mechanical
damage.
Only expert, qualified personnel must carry out the installation, in full compliance with the applicable law.
5 Installation
5.2 Tools and materials
Make sure you have all the tools and materials handy, to carry out the installation in total safety, according to the laws in-force.
Below is a drawing of the tools you will need to install the operator.
N.B.: An evaluation of the size of the cables with lengths other than the data in the table must be made based on the e ective
absorption of the connected devices, according to the instructions indicated by the CEI EN 60204-1 standards.
For connections that require several loads on the same line (sequential), the size given on the table must be re-evaluated based on
actual absorption and distances.
5.3 Cable list and minimun thickness
Connections Type of cable
Length of cable
1 < 10 m
Length of cable
10 < 20 m
Length of cable
20 < 30 m
120V-230V 2F power supply
FROR CEI
20-22
CEI EN
50267-2-1
3G x 1,5 mm
2
3G x 2,5 mm
2
3G x 4 mm
2
230V flashing lamp 2 x 0,5 mm
2
2 x 1 mm
2
2 x 1,5 mm
2
Photoelectric cells TX 2 x 0,5 mm
2
2 x 0.5 mm
2
2 x 0,5 mm
2
Photoelectric cells RX 4 x 0,5 mm
2
4 x 0,5 mm
2
4 x 0,5 mm
2
24V power supply accessory 2 x 0,5 mm
2
2 x 0,5 mm
2
2 x 1 mm
2
Control button 2 x 0,5 mm
2
2 x 0,5 mm
2
2 x 0,5 mm
2
Antenna connection RG58 max. 50 m
MM
MM
MM
6
5
9
3
1
2
4
9
10
10
11
7
6
5
9
3
1
2
4
12
11
1010
8
4
CAME
Pag.
5
-
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
BK-221 unit 1.
Control board incorporated2.
Radio receiver3.
Limit-switch tabs4.
Rack5.
Key-operated selector switch6.
Flashing light indicating door movement7.
Antenna8.
Safety photocells9.
Photocell column10.
Closure stop11.
The following applications are only examples, as the space required for unit installation and the accessories vary depending
on dimensions and therefore it is up to the installer to select the best solution.
Install the screws in the anchor plate and fasten them with a nut, then bend the preformed clamps downwards.
Construct a cement foundation that is large enough to accomodate the gear motor (it is a good idea to protrude 50 mm. from the
ground). When pouring the foundation, embed the gear motor anchor plate and the relative clamps in the cement.
The anchor bolts should be embedded in the concrete in the positions indicated; the drive unit is then attached to this bots. The anchor
plate must be perfectly level and absolutly clean; the bolts threads must be completly exposed.
N.B.: The fl exible tubes for the electrical wiring must be embedded in the base and protude in the correct position.
5.4 Motor to base anchorage
Fixing plate / Anchor stays
Cables
Concrete
base
Rack-limit
Gate wing
Wall
5÷10 mm.
Pag.
6
- Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
Horizontal adjustment
and unit anchorage
Vertical adjustment and
unit leveling
Cable entrances
Afstand tussen tandwiel en tandlat
Module M6 = 1,5 mm speling
During the initial phase of installation, the feet should protrude by 5-10 mm. in order to allow for alignment, anchorage of the
rack and further adjustments.
Perfect alignment with the guide rail is made possible by the (paten-ted) built-in regulation system, which consists of:
- slots for horizontal adjustment;
- threaded steel feet for vertical adjustment and levelling;
- plates and bolts for anchorage to the base.
5.5 Unit installation
5.6 Attaching the rack/limit
Attach the rack to the gate as described below:
- Release the gearmotor (parag. 5.8);
- position the rack on the pinion of the gearmotor and slide the gate manually in order to attach the rack along its entire length;
- when the rack is attached to the gate, adjust the feet using a screwdriver until the play between the pinion and the rack is correct
(1÷2 mm.).
N.B.: This position ensures that the weight of the gate does not rest on the gearmotor.
- If the rack is already attached, proceed directly to the adju-stment of the rack/pinion coupling.
- when the necessary adjustment have been completed, fasten the unit in position by tightening the two anchor bolts.
#!-%
#!-%
!
"
#!-%
#!-%
Pag.
7
-
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
BLOCK
RELEASE
To open the access door, insert the key A, push down and rotate clockwise. Then release the ratio motor by using key B on the
threelobed pin and turning it in the direction indicated.
To re-lock the reduction gear, turn key B in the direction indicated until it will move no further, without forcing it: the three-sid ed
pin will settle into place at the fi rst movement.
5.7 Attaching the switch tabs
Position the limit-switch tabs (whose positions determine the limits of gate travel) on the rack.
Note: do not allow the gate to strike the mechanical stops in the open or closed positions.
5.8 Manual release of the gearmotor
ATTENTION: the opening of the
unblock panel arrests the motor.
LN
L1T L2T
CT VS VF
UVWE
EX
26V 17V
01011
TS 1 2 3 3P 4 5 7 2 CX CY C7 C8 2 A B + E D FC FA F
4
10
11
6
812 13
9 1
7
5 2 3
Pag.
8
- Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
FUSE TABLE ZBK10
To protect: fuse:
Control board (line) 8 A-F
Accessories 1.6 A-F
Command devices 1 A-F
TECHNICAL INFORMATION
Power supply 230 V - 50 / 60 Hz
Absorption at rest 110 mA
Maximum power for 24V accessories 37 W
6 Control board
6.1 General description
6.2 Main components
Use 230V A.C. to power the electronic card using the L-N terminals, at a max 50/60Hz frequency.
Use 24V to power the command devices and accessories. Careful! The accessories cannot exceed 37W of overall power.
All connections are protected by quick-fuses – see table.
The input and output contact functions, the timing settings and users’ management, are set and viewed on the display, which is run by
software.
Warning! Before acting on the machinery, cut o the main power supply and disconnect any emergency batteries.
Display1.
Card fuse2.
Accessory fuse3.
Line fuse4.
AF card coupling for remote control5.
RSE card coupling for paired connections6.
230 V-power signalling LED7.
Connecting terminal board8.
Programming buttons9.
Display lighting adjustment trimmer10.
Memory roll board connector11.
Power supply terminals12.
Antenna terminals13.
COM
COM
NC
NC
NC
NC
COM
COM
Pag.
9
-
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
6.3 Electrical connections
230V (A.C.) motor
with encoder
Closing microswitch
Gearmotor, endstop and encoder
Modifications to the electrical connections for right-hand installations
Invert the gearmotor (U-V) and (FA-FC) endstop phases.
Opening microswitch
Description of the standard electrical connections for left-hand installations
Black
Red
Terminals for powering the following accessories:
- 24V A.C. Maximum allowed power: 37W
Power supply for accessories
230V (A.C.) Power, 50/60Hz
frequency
Cable lug with bolt and washer for connecting to earth.
Orange
Orange
White
Red
White
Red
Capacitor
Capacitor
Pag.
10
10 - Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
Open-gate status light
(contact range: 24V – 3W max)
- Signal that gate is open; turns o when
gate is closed.
Movement fl ashing light
(Contact range: 230V – 25W max).
- Flashes during the gate’s opening and
closing phases.
Command and control devices
Warning devices
Cycle lamp (contact rating: 230V – 60W max.).
- It lights up the driving area and stays on from the
moment the gate begins to open until it is fully closed
(including the automatic closing time). If automatic
closing is not activated, the lamp stays on only during
movement or for a set time of 5 minutes if used as a
courtesy lamp.
Courtesy lamp (Contact output: 230 V - 60 W max.)
- Auxiliary connection for suitably positioned external
lamp to increase lighting of the steering area. It
remain lit for a fi xed time of 5 minutes.
Stop button (N.C. contact) - Gate stop button. Excludes automatic
closing. For motion to resume, press the command button or the
remote control button.
N.B.: if contact is unused, select OFF on the “FUNCTIONS” menu.
Key selector and/or opening button (N.O. contact) -
Gate opening command.
Key selector and/or commands button (N.O.
contact) Commands for opening and closing the gate
– pressing the button or turning the key-switch, inverts
the gate’s movement or stops it depending on how it is
set on the 2-7 command in the “FUNCTIONS” menu
Key selector and/or partial opening button (N.O.
contact) - Partial gate opening for pedestrian access.
Key selector and/or closing button (N.O. contact) -
Gate closing command.
Antenna with RG58
cable for the remote
control.
or in alternative
or in alternative
RX
TX
RX TX
./ # .#

#./.#
6 6
.#
./
#
6
#./.#
Pag.
11
11 -
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
Safety devices
Confi gure either (N.C.) contacts CX or CY, input for
safety devices such as photocells, that comply with EN
12978 standards. See CX or CY input functions in:
- C1 «re-open during closing phase», When the gate
leaf is closing, opening the contact triggers the inversion
of the direction of movement until the gate leaf is fully
open.
- C2 «re-close during opening phase», When gate is
opening, if the contact is opened it triggers an inversion
of the direction until gate is fully closed;
- C3 «partial stop», gate stops if moving and
automatically shuts (if this functions has been selected);
- C4 «stand-by Obstacle», Halts the moving gate leaves
causing them to start moving again once obstacle is
removed.
- Deactivated, if the contact is unused.
DIR photocells
DOC photocells
Confi gure either (N.C.) contacts C7 or C8, input
for EN 12978 compliant safety devices such as
sensitive edges. See C7 or C8 input functions in:
- C7 «re-open during closing phase», - During
gate closing, opening the contact causes inversion
of movement until gate is fully open;
- C8 «re-close during opening phase», - During
gate opening, opening the contact causes inversion
of movement until gate is fully close;
OFF, is the contact is unused
DF with DFI connections monitor card

./
.#
#
&53)"),%M!
48
48
  48
#
.#
(DOC)
(DIR)
0
17
24
FRENO
1
2
3
4
SPUNTO
LN
L1T L2T
CT VS VF
UVWE
EX
26V 17V
01011
TS
Pag.
12
12 - Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
6.4 Electrical connection to operate the photocells’ safety test
At each open/close command, the card check the photocells’ e ciency.
Any problems with the photocells will cause the (PROG) Led to fl ash on the
electronic card, which cancels any commands from the radio transmitter or
push-button.
Electrical connection to operate the photocells’ safety test:
- The transmitter and receiver, must be connected as shown in the diagram;
- from the functions menu, select “safety tests” and select either CX or CY input/s to activate the test.
6.5 Motor torque limiter
To vary the motor torque, move the shown
faston (the one with the black wire) to one of the
4 positions: 1 min – 4 max.
WWW.CAME.IT
ZBK10
LANGUAGE
English
Þß
LANGUAGE
English
Þß
FUNCTIONS
English
Þß
TIMING ADJ.
Þß
A.C.T.
90s
Þß
Cycle Time
90s
Þß
Cycle Time
90s
Þß
Cycle Time
100s
Þß
LANGUAGE
Þß
Pag.
13
13 -
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
N.B.: when the menu is active, the system cannot be used.
The ENTER key is for:
- entering the menu
- confirming and memorising set values
The ESC key is for:
- exiting the menu
- cancelling modifications
The <> keys are for:
- shifting from one menu item to another
- increase or decrease values
the <...> symbols on the display are for:
- pointing out the currently, selected item
To enter the menu, keep the
ENTER key pressed for at least one
second.
To select a menu item,
mode using the greater
than-lesser than keys...
...then press ENTER
also use the greater
than-lesser than keys
for the “sub-menus”...
If the <> are on the TIME
function, you may modify the
value.
To increase or reduce
values, use the greater than-
lesser than keys...
...then press ENTER to confirm...
...to exit the menu, wait 30
seconds, or press ESC, until start
screen is displayed.
7 Programming
LANGUAGE
English
Þß
LANGUAGE
English
Þß
FUNCTIONS
English
Þß
TIMING ADJ.
Þß
A.C.T.
90s
Þß
Cycle Time
90s
Þß
Cycle Time
90s
Þß
Cycle Time
100s
Þß
LANGUAGE
Þß
7.1 Description of display commands
7.2 Browsing the menu
ENTER
>
ENTER
>
>
ENTER
>
>
ENTER
>>
>
ENTER
>
>
ENTER
>
>
ENTER
>
ENTER
>
ENTER
ENTER
ENTER
ENTER
ENTER
>
ENTER
ENTER
ENTER
>
>
>
>
>
>
>
>
>
>
>
>
>
ENTER
>
>
>
>
>
>
>
>
ENTER
>
>
>
ENTER
>
>
ENTER
>
>
ENTER
ENTER
>
>
ENTER
>
>
ENTER
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
< LANGUAGE >
<TIMING ADJ.>
<ADJUSTMENTS>
<English>
< INFO >
<Francais>
<Deutsch>
<Espanol><Italiano>
< A.C.T. >
< Cycle Time >
<Preflashing T.>
<Partial A.C.T.>
< New User >
< Modify User >
< Remove Usr. >
< Backup data >
<Restore backup>
<Delete all Usr>
<Gate run Adj >
< Slowdown >
<Gate run sens.>
<Slowdown sens.>
< Partial op. >
< Encoder >
< NET address >
< Startup Msg >
< 10s >
< FUNCTIONS >
< 11s >
< 90s >
< 91s >
< 5s >
< 6s >
< 5s >
< 6s >
<2-7 Func>
<Only Open>
< RADIO USRS >
Do you conf.?
< No >
< FW Version >
ver. 1.0
<Manoeuvres No.>
16480
<Partial>
Reading
ooooooo
••
Writing
ooooooo
••
n.001 In use
n.002 Empty
n.001 In use
n.002 Empty
< 10% >
< 11% >
< 10% >
< 11% >
< Disabled >
< Master >
< Slave >
WWW.CAME.IT
ZBK10
<
ON
>
<
OFF
>
<
-oooooooo+
>
<
-oooooooo+
>
<
-oooo+
>
<
-oooo+
>
Do you conf.?
< Yes >
Pag.
14
14 - Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
7.3 Menu structure
< LANGUAGE >
<TIMING ADJ.>
<ADJUSTMENTS>
<English>
< INFO >
<Francais>
<Deutsch>
<Espanol><Italiano>
< A.C.T. >
< Cycle Time >
<Preflashing T.>
<Partial A.C.T.>
< New User >
< Modify User >
< Remove Usr. >
< Backup data >
<Restore backup>
<Delete all Usr>
<Gate run Adj >
< Slowdown >
<Gate run sens.>
<Slowdown sens.>
< Partial op. >
< Encoder >
< NET address >
< Startup Msg >
< 10s >
< FUNCTIONS >
< 11s >
< 90s >
< 91s >
< 5s >
< 6s >
< 5s >
< 6s >
<2-7 Func>
<Only Open>
< RADIO USRS >
Do you conf.?
< No >
< FW Version >
ver. 1.0
<Manoeuvres No.>
16480
<Partial>
Reading
ooooooo
••
Writing
ooooooo
••
n.001 In use
n.002 Empty
n.001 In use
n.002 Empty
See detailed
description on
chap. 7.14
< 10% >
< 11% >
< 10% >
< 11% >
< Disabled >
< Master >
< Slave >
WWW.CAME.IT
ZBK10
<
ON
>
<
OFF
>
<
-oooooooo+
>
<
-oooooooo+
>
<
-oooo+
>
<
-oooo+
>
Do you conf.?
< Yes >
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
>
>
>
>
>
>
>
>>
>
>
>
>
>
>
>
>
>
>
>>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
< ON >
< OFF >
<Op.-Stop-Cl.>
<Open Close>
< Disabled > < C1 >
< C2 >< C3 >< C4 >
< Disable > <Enabled on CX>
<Enabled on CY><Enabled CX+CY>
< Autom.Clos. >
< 2-7 Command >
< Preflash >
<Maintained Act>
<Maint. Act. Cl.>
< CY Input >
< C7 Input >
< C8 Input >
< STOP (1) >
< Safety test >
< Lamp Output >
< CX Input >
< ON >
< OFF >
< ON >
< OFF >
< ON >
< OFF >
< Disabled > < C1 >
< C2 >< C3 >< C4 >
< ON >
< OFF >
< ON >
< OFF >
< ON >
< OFF >
< Cycle >
< Courtesy >< Fl. light >
< Obst. Detect >
< ON >
< OFF >
Pag.
15
15 -
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
< ON >
< OFF >
<Op.-Stop-Cl.>
<Open Close>
< Disabled > < C1 >
< C2 >< C3 >< C4 >
< Disable > <Enabled on CX>
<Enabled on CY><Enabled CX+CY>
< Autom.Clos. >
< 2-7 Command >
< Preflash >
<Maintained Act>
<Maint. Act. Cl.>
< CY Input >
< C7 Input >
< C8 Input >
< STOP (1) >
< Safety test >
< Lamp Output >
< CX Input >
< ON >
< OFF >
< ON >
< OFF >
< ON >
< OFF >
< Disabled > < C1 >
< C2 >< C3 >< C4 >
< ON >
< OFF >
< ON >
< OFF >
< ON >
< OFF >
< Cycle >
< Courtesy >< Fl. light >
< Obst. Detect >
< ON >
< OFF >
>
X 2
X 2
LANGUAGE
English
FUNCTIONS TIMING ADJ.
RADIO USRSADJUSTMENTS
INFO
< LANGUAGE >
English
LANGUAGE
< English >
LANGUAGE
< Francais >
LANGUAGE
< Deutsch >
LANGUAGE
< Espanol >
LANGUAGE
< Italiano >
< Autom.Clos. >
ON
Autom.Clos.
< ON >
Autom.Clos.
< OFF >
< 2-7 Command >
Op.-Stop-Cl.
2-7 Command
< Op.-Stop-Cl. >
2-7 Command
< Open Close >
FUNCTIONS
FUNCTIONS
Pag.
16
16 - Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
7.4 Main menu
LANGUAGE
English
FUNCTIONS TIMING ADJ.
RADIO USRSADJUSTMENTS
INFO
Press ENTER for
1 second
7.5 Language menu
Select language: selects among the languages displayed.
< LANGUAGE >
English
LANGUAGE
< English >
LANGUAGE
< Francais >
LANGUAGE
< Deutsch >
LANGUAGE
< Espanol >
LANGUAGE
< Italiano >
FUNCTIONS
FUNCTIONS
FUNCTIONS
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
IMING ADJ
IMING ADJ
RADIO USRS
ADIO USRS
ADIO USRS
ADJUSTMENTS
ADJUSTMENTS
DJUSTMENT
DJUSTMENT
7.6 Functions menu
< Autom.Clos. >
ON
Autom.Clos.
< ON >
Autom.Clos.
< OFF >
Automatic Closing: activates or deactivates the automatic closing function.
The automatic closing timer activates at each opening endpoint. The predetermined time may be adjusted, and is in any case
dependent on any safety devices that may activate; and it does not activate after a total safety “stop” or during a power outage.
2-7 Command: sets the sequential command.
“Open-close” or “open-stop-close-stop” function with button [2-7] and radio transmitter (when radio-frequency card is inserted)
< 2-7 Command >
Op.-Stop-Cl.
2-7 Command
< Op.-Stop-Cl. >
2-7 Command
< Open Close >
INFO
INFO
INFO
INFO
<
LANGUAGE
>
< LANGUAGE >
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
IMING ADJ
IMING ADJ
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
<
LANGUAGE
>
< LANGUAGE >
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
X 2
X 2
X 2
X 2
X 3
X 2
X 4
X 5
< Preflash >
OFF
Preflash
< OFF >
Preflash
< ON >
< CX Input >
Disabled
CX Input
< Disabled >
CX Input
< C1 >
CX Input
< C2 >
CX Input
< C3 >
CX Input
< C4 >
Maintained Act
< OFF >
<M aintained Act>
OFF
Maintained Act
< ON >
Maint.Act. Cl.
< OFF >
< Maint.Act. Cl. >
OFF
Maint.Act. Cl.
< ON >
FUNCTIONS
FUNCTIONS
FUNCTIONS
FUNCTIONS
Pag.
17
17 -
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
Pre-flashing: after an opening or closing command, the fl ashing light, connected to E-EX, starts fl ashing before the gate begins its run
(to set the time, see “Pre-fl ashing timing” from the Adjust Timings menu
< Preflash >
OFF
Preflash
< OFF >
Preflash
< ON >
Maintained action: The gate works by keeping the button pressed (button 2-3 for opening, button 2-4 for closing, or if set to the “On Closing”
function, only with button 2-4.
Closing maintained action: the gate closes by keeping the button pressed (only for the 2-4 closing button).
CX input: N.C. safety contact input, lets you pair up the following functions: C1 (re-opening during closing), C2 (re-closing during opening), C3
(partial stop), C4 (obstacle stall), or, deactivated
< CX Input >
Disabled
CX Input
< Disabled >
CX Input
< C1 >
CX Input
< C2 >
CX Input
< C3 >
CX Input
< C4 >
Maintained Act
< OFF >
<M aintained Act>
OFF
Maintained Act
< ON >
Maint.Act. Cl.
< OFF >
< Maint.Act. Cl. >
OFF
Maint.Act. Cl.
< ON >
< LANGUAGE >
< LANGUAGE >
LANGUA
ANGUA
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
<
LANGUAGE
>
< LANGUAGE >
English
English
English
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
< LANGUAGE >
< LANGUAGE >
LANGUAGLANGUAG
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
< LANGUAGE >
< LANGUAGE >
ANGUA
ANGUA
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING ADTIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
X 2
X 8
X 2
X 6
X 2
X 7
X 2
X 9
C8 Input
< OFF >
< C8 Input >
OFF
C8 Input
< ON >
< CY Input >
Disabled
CY Input
< Disabled >
CY Input
< C1 >
CY Input
< C2 >
CY Input
< C3 >
CY Input
< C4 >
C7 Input
< OFF >
< C7 Input >
OFF
C7 Input
< ON >
STOP (1)
< ON >
< STOP (1) >
OFF
STOP (1)
< OFF >
FUNCTIONS
FUNCTIONS
FUNCTIONS
FUNCTIONS
Pag.
18
18 - Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
CY input: N.C. safety contact input, lets you pair up the following functions: C1 (re-opening during closing), C2 (re-closing during opening), C3
(partial stop), C4 (obstacle stall), or, deactivated
C7 input: N.C. safety contact input (re-opening when closing). This input is for EN 12978-compliant safety devices, like sensitive edges. When
the gate is closing, the open contact triggers an inversion in the gate’s movement until it is fully opened.
C8 input: N.C. safety contact input (re-closing during opening). This input is for EN 12978-compliant safety devices, like sensitive edges. When
the gate is opening, the open contact triggers an inversion in the gate’s movement until it is fully closed.
C8 Input
< OFF >
< C8 Input >
OFF
C8 Input
< ON >
< CY Input >
Disabled
CY Input
< Disabled >
CY Input
< C1 >
CY Input
< C2 >
CY Input
< C3 >
CY Input
< C4 >
C7 Input
< OFF >
< C7 Input >
OFF
C7 Input
< ON >
STOP (1)
< ON >
< STOP (1) >
OFF
STOP (1)
< OFF >
<
LANGUAGE
>
< LANGUAGE >
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
< LANGUAGE >
< LANGUAGE >
ANGUA
ANGUA
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
<
LANGUAGE
>
< LANGUAGE >
English
English
h
h
FUNCTIONS
TIMING ADJ.TIMING ADJ.
TIMING ADTIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
<
LANGUAGE
>
< LANGUAGE >
English
English
English
English
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
STOP (1): this function stops the gate and consequently excludes any automatic closing cycle; for movement to resume, you need to use
the keypad or transmitter. Insert safety device on [1-2]; is unused, select “OFF” and confirm with ENTER.
X 2
X 12
X 2
X10
X 2
X 11
Obst. Detect
< OFF >
< Obst. Detect >
OFF
Obst. Detect
< ON >
< Safety Test >
Disable
< Lamp Output >
Courtesy
Safety Test
<Enabled on CX>
Safety Test
<Enabled on CY>
Safety Test
< En.on CX + CY >
Lamp Output
< Courtesy >
Lamp Output
< Fl. light >
Lamp Output
< Cycle >
Safety Test
< Disable >
FUNCTIONS
FUNCTIONS
FUNCTIONS
Pag.
19
19 -
Manual code
:
119BV25
119 BV25 ver.
1.2
1.2 08/2011
© CAME cancelli automatici s.p.a. -
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
Safety test: Allows the card to check the efficiency of any safety devices (i.e. photocells) after every opening or closing command.
Lamp output: to configure the lamp connected to E-Ex:
- cycle: outdoor lamp, which can be positioned at leisure, for better illumination in the parking/driveway area.
It stays on from the moment the gate leaf begins to open, until it is fully closed (including automatic closing time).
In case the automatic closing function is not inserted, it stays on only during gate movement.
- courtesy: outdoor lamp, which can be positioned at leisure, for better illumination in the parking/driveway area.
It stays on for a set time of 5 minutes.
- flashing light: signals the gate opening or closing movement.
Obstacle detected - When motor is stopped (gate closed or after a total stop command) it prevents any movement if safety devices,
such as photocells, detect any obstacles.
Obst. Detect
< OFF >
< Obst. Detect >
OFF
Obst. Detect
< ON >
< Safety Test >
Disable
< Lamp Output >
Courtesy
Safety Test
<Enabled on CX>
Safety Test
<Enabled on CY>
Safety Test
< En.on CX + CY >
Lamp Output
< Courtesy >
Lamp Output
< Fl. light >
Lamp Output
< Cycle >
Safety Test
< Disable >
< LANGUAGE >
< LANGUAGE >
ANGUA
ANGUA
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
< LANGUAGE >
< LANGUAGE >
ANGUA
ANGUA
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
<
LANGUAGE >
< LANGUAGE >
English
English
h
h
FUNCTIONS
TIMING ADJ.
TIMING ADJ.
TIMING AD
TIMING AD
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
X 2
X 2
X 2
X 2
X 2
X 3
< A.C.T >
10 s
A.C.T.
< 10 s >
A.C.T.
< 11 s >
< Cycle Time >
90 s
Cycle Time
< 90 s >
< Preflashing T. >
5 s
Preflashing T.
< 5 s >
< Partial A.C.T. >
5 s
Partial A.C.T.
< 5 s >
TIMING ADJ.
Cycle Time
< 91 s >
Preflashing T.
< 6 s >
Partial A.C.T.
< 6 s >
TIMING ADJ.
TIMING ADJ.
TIMING ADJ.
Pag.
20
20 - Manual code:
119BV25
119 BV25 ver.
1.2
1.2 08/2011 © CAME cancelli automatici s.p.a. - The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
ENGLISH
< A.C.T >
10 s
A.C.T.
< 10 s >
A.C.T.
< 11 s >
7.7 Time setting menu
Automatic closing: to set the waiting time when gate is in the open position.
Once this time is elapsed, the gate closes automatically. The waiting time can be set to between 0” and 120”.
< Cycle Time >
90 s
Cycle Time
< 90 s >
Working time: the motor’s working time during opening or closing; from 10” to 120”.
< Preflashing T. >
5 s
Preflashing T.
< 5 s >
Pre-flashing time: after an opening or closing command is given, the flasher connected to “E-EX), flashes for between 1” and 10”,
before the gate begins to move.
< Partial A.C.T. >
5 s
Partial A.C.T.
< 5 s >
Automatic partial closing: gate leaf’s waiting time, after a partial opening command is given. The waiting time can be set to between
0” and 120”.
<
LANGUAGE
>
< LANGUAGE >
English
English
h
h
FUNCTIONS
FUNCTIONS
FUNCTION
FUNCTION
TIMING ADJ.
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
Cycle Time
< 91 s >
Preflashing T.
< 6 s >
Partial A.C.T.
< 6 s >
<
LANGUAGE
>
< LANGUAGE >
English
English
English
English
FUNCTIONS
FUNCTIONS
FUNCTION
FUNCTION
TIMING ADJ.
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
<
LANGUAGE
>
< LANGUAGE >
English
English
English
English
FUNCTIONS
FUNCTIONS
FUNCTION
FUNCTION
TIMING ADJ.
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
<
LANGUAGE
>
< LANGUAGE >
English
English
h
h
FUNCTIONS
FUNCTIONS
FUNCTIONS
FUNCTIONS
TIMING ADJ.
RADIO USR
RADIO USR
ADJUSTMENTS
ADJUSTMENTS
DJUSTMEN
DJUSTMEN
INFO
INFO
INFO
INFO
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

CAME BK-221 Installation guide

Category
Gate Opener
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI