Mircom LT-6749-MGC-4000-BR-DIN-Rail-Template Template

Mircom
Brand
Mircom
Model
LT-6749-MGC-4000-BR-DIN-Rail-Template
Type
Template

Mircom LT-6749-MGC-4000-BR-DIN-Rail-Template

This template is designed to aid in the proper spacing of DIN rails in an enclosure. It can be used for enclosures with 1, 2, or 3 DIN rails. The template includes a drill hole drill diameter of 9/64".

For enclosures with 1 or 2 modules, the minimum dimensions are 9" (229 mm) x 12.75" (324 mm) x 3.15" (80 mm). There should be a minimum of 10 conduit knockouts. The minimum distance from the DIN rail to the top of the enclosure should be 3" (76 mm) and the minimum distance from the DIN rail to the bottom of the enclosure should be 3" (76 mm).

Mircom LT-6749-MGC-4000-BR-DIN-Rail-Template

This template is designed to aid in the proper spacing of DIN rails in an enclosure. It can be used for enclosures with 1, 2, or 3 DIN rails. The template includes a drill hole drill diameter of 9/64".

For enclosures with 1 or 2 modules, the minimum dimensions are 9" (229 mm) x 12.75" (324 mm) x 3.15" (80 mm). There should be a minimum of 10 conduit knockouts. The minimum distance from the DIN rail to the top of the enclosure should be 3" (76 mm) and the minimum distance from the DIN rail to the bottom of the enclosure should be 3" (76 mm).

165
6.5"
274
10 13
16
"
6
1
4
"
18
11
16
"
250
913
16
"
12
1
2
"
274
Use this template to properly space the DIN rails in the enclosure.
Drill hole drill diameter: 9/64”
See page 2 for cable routing
LT-6749 rev 3
June 2023
Page 1
MGC-4000-BR DIN Rail Kit
Contents of kit: 3 DIN rails, 12
screws (#8 type AB 1/4” length), 12 at washers,
6 brackets, 6 nuts for the brackets
For 1 or 2 modules:
• UL or equivalent listed enclosure with 1 DIN rail
• Minimum dimensions 9” (229 mm) x 12.75” (324 mm) x 3.15” (80 mm)
• Minimum of 10 conduit knockouts
• Minimum distance from the DIN rail to top of enclosure: 3" (76 mm) (measured from the center of the rail)
• Minimum distance from the DIN rail to bottom of enclosure: 3" (76 mm) (measured from the center of the rail)
For 3 to 6 modules:
• UL or equivalent listed enclosure with 3 DIN rails
• Minimum dimensions 23” (584 mm) x 12.5” (318 mm) x 4.2” (107 mm)
• Minimum of 13 conduit knockouts
• Minimum distance from the top DIN rail to top of enclosure: 3" (76 mm) (measured from the center of the rail)
• Minimum distance from rst rail to second rail: 6" (152 mm) (measured from the center of the rails)
• If using a third DIN rail, minimum distance from second rail to third rail: 6" (152 mm) (measured from the center of the rails)
• Minimum distance from the bottom DIN rail to bottom of enclosure: 3" (76 mm) (measured from the center of the rail)
Means of securing door: key or tool
Nut
DIN rail
Enclosure
Bracket
Bracket
NutNut
Nut
FRONT VIEW
TOP VIEW
DIN rail
Bracket Bracket
Enclosure
2 included
screws
#8
type AB
and washers
2 included screws
#8 type AB
and washers
Bracket Installation
Minimum
1/4”
Min. 1/4”
Minimum
1/4”
Minimum 1/4”
Minimum 1/4”
to third DIN rail wiring
Minimum 1/4”
Minimum 1/4”
to third DIN rail wiring
Minimum 1/4”
Minimum 1/4”
Min.
1/4”
Min. 1/4”
Min.
1/4”
Min. 1/4”
Cable Routing Examples
LT-6749 rev 3
June 2023
Page 2
1 or 2 Modules
Maintain a separation of 1/4” (6.4 mm)
minimum between power-limited and
non-power-limited wiring at all times.
Right side of box is
reserved for all power
limited wiring.
Gray area (solid
outline) marks the
location for all
non-power-limited
wiring.
Green area (dotted
outline) marks the
location for all
power-limited wiring.
3 to 6 Modules
  • Page 1 1
  • Page 2 2

Mircom LT-6749-MGC-4000-BR-DIN-Rail-Template Template

Mircom
Brand
Mircom
Model
LT-6749-MGC-4000-BR-DIN-Rail-Template
Type
Template

Mircom LT-6749-MGC-4000-BR-DIN-Rail-Template

This template is designed to aid in the proper spacing of DIN rails in an enclosure. It can be used for enclosures with 1, 2, or 3 DIN rails. The template includes a drill hole drill diameter of 9/64".

For enclosures with 1 or 2 modules, the minimum dimensions are 9" (229 mm) x 12.75" (324 mm) x 3.15" (80 mm). There should be a minimum of 10 conduit knockouts. The minimum distance from the DIN rail to the top of the enclosure should be 3" (76 mm) and the minimum distance from the DIN rail to the bottom of the enclosure should be 3" (76 mm).

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents