Eaton 93E 30ITC Installation guide

Eaton

®

93E Integrated Transformer Cabinet

30ITC and 60ITC

Installation Manual

Eaton

®

93E Integrated Transformer Cabinet

30ITC and 60ITC

Installation Manual

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during installation and

maintenance of the UPS system and batteries. Read all instructions before operating the

equipment and save this manual for future reference.

CONSIGNES DE SÉCURITÉ IMPORTANTES CONSERVER CES INSTRUCTIONS

Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute

procédure d'installation et de maintenance des batteries et de l'onduleur. Veuillez consulter

entièrement ces instructions avant de faire fonctionner l'équipement et conserver ce manuel afin

de pouvoir vous y reporter ultérieurement.

Eaton is a registered trademarks of Eaton Corporation or its subsidiaries and affiliates. National Electrical Code

and NEC are registered trademarks of National Fire Protection Association, Inc. All other trademarks are

property of their respective companies.

be reproduced in any way without the express written approval of Eaton Corporation.

Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality i

Table of Contents

1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

1.1 Installation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.2 Model Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

1.3 Using This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1.4 Conventions Used in This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1.5 Symbols, Controls, and Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

1.6 For More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

1.7 Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5

2 SAFETY WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

3 INSTALLATION PLAN AND UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.1 Creating an Installation Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2 Preparing the Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2.1 Environmental and Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

3.2.2 ITC Power Wiring Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

3.3 Inspecting and Unpacking the ITC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14

3.4 Transformer Breaker Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

4 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.1 Preliminary Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.2 Unloading the ITC from the Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.2.1 Unloading the 30ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

4.2.2 Unloading the 60ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

4.3 Installing the Power Terminal Cover Base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

4.4 Installing ITC External Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

4.4.1 Single-Feed UPS with Input Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

4.4.2 Single-Feed UPS with Input and Output Transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

4.4.3 Dual-Feed UPS with Two Input Transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23

4.4.4 Dual-Feed UPS with Two Input Transformers and One Output Transformer . . . . . . . . . . . . . . . . . . . 4-24

4.5 Initial Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

4.6 Completing the Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27

5 ONELINES AND SCHEMATICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.1 Onelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

5.2 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.1 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.2 Performing Preventive Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.2.1 DAILY Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.2.2 PERIODIC Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.2.3 ANNUAL Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

6.3 Recycling the ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

6.4 Maintenance Training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

Table of Contents

ii Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality

7 PRODUCT SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.1 Model Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.2.1 Input Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.2.2 Output Transformer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

7.2.3 Environmental and Safety Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W-1

Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality iii

List of Figures

Figure 1-1. Eaton 93E 30ITC and Eaton 93E 60ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Figure 1-3. Eaton 93E 60 kVA UPS and Eaton 93E 60ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Figure 3-1. 93E 30ITC Cabinet Dimensions (Front, Right Side, and Rear Views) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Figure 3-2. 93E 30ITC Dimensions (Top and Bottom Views) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Figure 3-3. 93E 30ITC Center of Gravity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5

Figure 3-4. 93E 60ITC Cabinet Dimensions (Front, Right Side, and Rear Views) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Figure 3-5. 93E 60ITC Dimensions (Top and Bottom Views) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7

Figure 3-6. 93E 60ITC Center of Gravity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8

Figure 3-7. Eaton 93E 30ITC and Eaton 93E 60ITC as Shipped on Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

Figure 3-8. Eaton 93E 30ITC and Eaton 93E 60ITC Transformer Breaker

Locations – Front Views with Doors Removed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16

Figure 4-1. Removing the Front Shipping Bracket – 93E 30ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Figure 4-2. Removing the Rear Shipping Bracket – 93E 30ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Figure 4-3. Installing the Pallet Extension Plate – 93E 30ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Figure 4-4. Removing the Pallet Skids and Supports – 93E 60ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7

Figure 4-5. ITC Power Terminal Cover Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

Figure 4-6. Eaton 93E 30ITC Power Terminal Cover Base Installation and Conduit Wire Entry Location . . . . . . . . . . . . 4-9

Figure 4-7. Eaton 93E 60ITC Power Terminal Cover Base Installation and Conduit Wire Entry Location . . . . . . . . . . . . 4-10

Figure 4-8. Wire Tray Location – 93E 30ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

Figure 4-9. Wire Tray Location – 93E 60ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

Figure 4-10. Input and Output Power Terminal Locations – 93E 30ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14

Figure 4-11. Output Transformer Breaker Terminal Detail – 93E 30ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Figure 4-12. Input Transformer Breaker Terminal Detail – 93E 30ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15

Figure 4-13. Input and Output Power Terminal Locations – 93E 60ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16

Figure 4-14. Output Transformer Breaker Terminal Detail – 93E 60ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Figure 4-15. Input Transformer Breaker Terminal Detail – 93E 60ITC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

Figure 4-16. ITC and UPS Power Terminal Cover Base Wiring Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18

Figure 4-17. ITC Power Terminal Cover Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19

Figure 4-18. ITC Power Terminal Cover Splice Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20

Figure 5-1. 93E 30ITC and 93E 60ITC Internal Oneline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Figure 5-2. Dual Transformer 93E 30ITC and 93E 60ITC Intercabinet Interconnection Oneline . . . . . . . . . . . . . . . . . . . 5-2

Figure 5-3. 93E 30ITC and 93E 60ITC Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

List of Figures

iv Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality

This page intentionally left blank.

Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality v

List of Tables

Table 3-1. ITC Weights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Table 3-2. ITC Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Table 3-3. Cooling Requirements During Full Load Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Table 3-4. External Power Wiring Requirements for the Eaton 93E 30ITC and 93E 60ITC – Single Transformer . . . . . 3-10

Table 3-5. External Power Wiring Requirements for the Eaton 93E 30ITC and 93E 60ITC – Dual Transformer . . . . . . 3-11

Table 3-6. External Input Power Cable Terminations for the Eaton 93E 30ITC – Single Transformer . . . . . . . . . . . . . . 3-12

Table 3-7. External Input Power Cable Terminations for the Eaton 93E 30ITC – Dual Transformer . . . . . . . . . . . . . . . 3-12

Table 3-8. External Input Power Cable Terminations for the Eaton 93E 60ITC – Single Transformer . . . . . . . . . . . . . . 3-13

Table 3-9. External Input Power Cable Terminations for the Eaton 93E 60ITC – Dual Transformer . . . . . . . . . . . . . . . 3-13

List of Tables

vi Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality

This page intentionally left blank.

Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality 1-1

Chapter 1 Introduction

The Eaton

®

Integrated Transformer Cabinet (ITC) provides voltage transformation and isolation for the

93E 20–30 kVA and 40–60 kVA Uninterruptable Power Supply (UPS) to enhance the usability and reliability of

the systems. Two models are available, the 93E 30ITC and 93E 60ITC to match the installed Eaton 93E UPS.

A 480/208 Vac input isolation transformer provides an isolated input to the UPS rectifier for applications that

require an input of 480 Vac.

An optional 208/480 Vac output isolation transformer provides an isolated output to the critical load or for

applications that require 480 Vac. To save space, the transformer is contained in the same ITC as the input

transformer.

The ITC is housed in a single free-standing cabinet with a safety shield behind the door for hazardous voltage

protection. The cabinets match the UPS cabinet in style and color.

Figure 1-1 shows the Eaton 93E 30ITC and Eaton 93E 60ITC.

Figure 1-1. Eaton 93E 30ITC and Eaton 93E 60ITC

NOTE Startup and operational checks must be performed by an authorized Eaton

Customer Service Engineer, or the warranty terms specified on page W-1 become

void. This service is offered as part of the sales contract for the UPS. Contact an

Eaton service representative in advance (usually a two-week notice is required) to

reserve a preferred startup date.

93E 30ITC

93E 60ITC

Introduction

1-2 Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality

1.1 Installation Features

The ITC is designed to be installed in a line-up-and-match or standalone configuration. In a line-up-and-match

configuration power wiring may be routed either external to the cabinet using conduit or the power terminal

wiring channel assembly may be utilized to pass wiring between adjacent cabinets. In standalone

configurations power wiring is routed using external conduit.

To reduce installation time, wiring enters the ITC from the back and is routed to the front panel for easy

connection to the mechanical lugs located on the input and output circuit breakers.

A line-up-and-match ITC is installed adjacent to the UPS or other accessory cabinet. The recommended

installation location is to the left of the UPS cabinet. See Figure 1-2 and Figure 1-3 for line-up-and-match

configuration views.

1.2 Model Configurations

The following model configurations are available:

l

93E 30ITC for use with the 93E 30 kVA UPS

- Single Transformer Cabinet: Contains a three-phase 480 Vac to 208Y/120 Vac input isolation transformer

- Dual Transformer Cabinet: Contains a three-phase 480 Vac to 208Y/120 Vac input isolation transformer

and a three-phase 208 Vac to 480Y/277 Vac output isolation transformer

l

93E 60ITC for use with the 93E 60 kVA UPS

- Single Transformer Cabinet: Contains a three-phase 480 Vac to 208Y/120 Vac input isolation transformer

- Dual Transformer Cabinet: Contains a three-phase 480 Vac to 208Y/120 Vac input isolation transformer

and a three-phase 208 Vac to 480Y/277 Vac output isolation transformer

Introduction

Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality 1-3

Figure 1-2. Eaton 93E 30 kVA UPS and Eaton 93E 30ITC

Figure 1-3. Eaton 93E 60 kVA UPS and Eaton 93E 60ITC

UPS93E 30ITC

UPS93E 60ITC

Introduction

1-4 Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality

1.3 Using This Manual

This manual describes how to install the ITC. Read and understand the procedures described to ensure

trouble-free installation and operation.

Read through each procedure before beginning the procedure. Perform only those procedures that apply to the

UPS system being installed or operated.

1.4 Conventions Used in This Manual

This manual uses these type conventions:

l

Bold type highlights important concepts in discussions, key terms in procedures, and menu options, or

represents a command or option that you type or enter at a prompt.

l

Italic type highlights new terms where they are defined.

l

Screen type represents information that appears on the screen or LCD.

In this manual, the term UPS refers only to the UPS cabinet and its internal elements. The term UPS system

refers to the entire power protection system – the UPS cabinet, an external battery system, and options or

accessories installed.

The term line-up-and-match refers to accessory cabinets that are physically located adjacent to the UPS. The

term standalone refers to accessory cabinets that are located separate from the UPS.

1.5 Symbols, Controls, and Indicators

The following are examples of symbols used on the UPS or accessories to alert you to important information:

Icon Description

NOTE Information notes call attention to important features or instructions.

[Keys] Brackets are used when referring to a specific key, such as [Enter] or [Ctrl].

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk

of electric shock symbol.

CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's

manual for additional information, such as important operating and

maintenance instructions.

This symbol indicates that you should not discard the UPS or the UPS

batteries in the trash. This product contains sealed, lead-acid batteries and

must be disposed of properly. For more information, contact your local

recycling/reuse or hazardous waste center.

This symbol indicates that you should not discard waste electrical or

electronic equipment (WEEE) in the trash. For proper disposal, contact your

local recycling/reuse or hazardous waste center.

Introduction

Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality 1-5

1.6 For More Information

Refer to the Eaton 93E UPS (20-30 kVA, 208/220V) Generation 3 Installation and Operation Manual or

Eaton 93E UPS (40-60 kVA, 208/220V) Generation 3 Installation and Operation Manual for the following

additional information:

l

UPS, optional components, and accessory installation instructions, including site preparation, planning for

installation, and wiring and safety information (detailed illustrations of cabinets and optional accessories with

dimensional and connection point drawings are provided)

l

UPS operation, including UPS controls, functions of the UPS, standard features and optional accessories,

procedures for starting and stopping the UPS, and information about maintenance and responding to

system events

l

Communication capabilities of the UPS system

Refer to the Eaton 93E Integrated Accessory Cabinet-Distribution Installation Manual for the following

additional information:

l

Installation instructions, including site preparation, planning for installation, wiring and safety information,

and detailed illustrations of cabinets with dimensional and connection point drawings

Refer to the Eaton 93E Integrated Accessory Cabinet-Tie and Bypass Installation and Operation Manual for the

following additional information:

l

Operation, including breakers, standard features and optional accessories, procedures for using the bypass

functions, and information about maintenance

l

Installation instructions, including site preparation, planning for installation, wiring and safety information,

and detailed illustrations of cabinets with dimensional and connection point drawings

Visit www.eaton.com/powerquality or contact an Eaton service representative for information on how to obtain

copies of these manuals.

1.7 Getting Help

If help is needed with any of the following:

l

Scheduling initial startup

l

Regional locations and telephone numbers

l

A technical question about any of the information in this manual

l

A question this manual does not answer

Please call the Customer Reliability Center at:

United States: 1-800-843-9433

Canada: 1-800-461-9166 ext 260

All other countries: Call your local service representative

Please use the following e-mail address for manual comments, suggestions, or to report an error in this manual:

E-ESSDocumentation@eaton.com

Introduction

1-6 Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality

This page intentionally left blank.

Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality 2-1

Chapter 2 Safety Warnings

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during installation and

maintenance of the UPS system and batteries. Read all instructions before operating the

equipment and save this manual for future reference.

The UPS system is designed for industrial or computer room applications, and contains safety

shields behind the door and front panels. However, the UPS system is a sophisticated power

system and should be handled with appropriate care.

DANGER

This UPS system contains LETHAL VOLTAGES. All repairs and service should be performed by

AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS inside the

UPS.

WARNING

l

The UPS system is powered by its own energy source (batteries). The output terminals may

carry live voltage even when the UPS is disconnected from an AC source.

l

To reduce the risk of fire or electric shock, install this UPS system in a temperature and humidity

controlled, indoor environment, free of conductive contaminants. Ambient temperature must

not exceed 30C (86F). Do not operate near water or excessive humidity (95% maximum). The

system is not intended for outdoor use.

l

As a result of the connected loads, high leakage current is possible. Connection to earth ground

is required for safety and proper product operation. Do not check UPS system operation by any

action that includes removal of the earth (ground) connection with loads attached.

l

Ensure all power is disconnected before performing installation or service.

l

ELECTRIC ENERGY HAZARD. Do not attempt to alter any UPS system or battery wiring or

connectors. Attempting to alter wiring can cause injury.

CAUTION

l

Installation or servicing should be performed by qualified service personnel knowledgeable of

UPS and battery systems, and required precautions. Keep unauthorized personnel away from

equipment. Consider all warnings, cautions, and notes before installing or servicing equipment.

l

Keep the Accessory cabinet doors closed and front panels installed to ensure proper cooling

airflow and to protect personnel from dangerous voltages inside the unit.

l

Do not install or operate the UPS system close to gas or electric heat sources.

l

The operating environment should be maintained within the parameters stated in this manual.

l

Keep surroundings uncluttered, clean, and free from excess moisture.

l

Observe all DANGER, WARNING, and CAUTION notices affixed to the inside and outside of the

equipment.

Safety Warnings

2-2 Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality

This page intentionally left blank.

Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality 3-1

Chapter 3 Installation Plan and Unpacking

Use the following basic sequence of steps to install the Eaton 93E 30 or Eaton 93E 60 Integrated Transformer

Cabinet (ITC):

1. Create an installation plan for the ITC (Chapter 3).

2. Prepare your site for the ITC (Chapter 3).

3. Inspect and unpack the ITC (Chapter 3).

4. Unload and install the ITC, and wire the system (Chapter 4).

5. Complete the Installation Checklist (Chapter 4).

6. Have authorized service personnel perform preliminary operational checks and start up the system.

3.1 Creating an Installation Plan

Before installing the ITC, read and understand how this manual applies to the system being installed. Use the

procedures and illustrations in this section to create a logical plan for installing the ITC. This section contains

the following information:

l

Physical features and requirements, including dimensions

l

Power wiring installation notes

l

Location of conduit and wire entry landing plates

l

Location of power terminals

3.2 Preparing the Site

For the UPS system to operate at peak efficiency, the installation site should meet the environmental

parameters outlined in this manual. If the UPS system is to be operated at an altitude higher than 1500m

(5000 ft), contact an Eaton service representative for important information about high altitude operation. The

operating environment must meet the weight, clearance, and environmental requirements specified for the

applicable accessory cabinet.

3.2.1 Environmental and Installation Considerations

The UPS system installation, including the ITC, must meet the following guidelines:

l

The system must be installed on a level floor suitable for computer or electronic equipment.

l

The system must be installed in a temperature and humidity controlled indoor area free of conductive

contaminants.

Failure to follow guidelines may void your warranty.

The ITC operating environment must accommodate the weight requirements shown in Table 3-1 and the size

requirements shown in Figure 3-1 through Figure 3-6.

NOTE Startup and operational checks must be performed by an authorized Eaton

Customer Service Engineer, or the warranty terms specified on page W-1 become

void. This service is offered as part of the sales contract for the UPS. Contact an

Eaton service representative in advance (usually a two-week notice is required) to

reserve a preferred startup date.

Installation Plan and Unpacking

3-2 Eaton 93E Integrated Transformer Cabinet (ITC) Installation Manual P-164000074—Rev 3 www.eaton.com/powerquality

The 93E 30ITC uses forced air cooling and the 93E 60ITC uses convection cooling to regulate internal

component temperature. Air inlets are in the front of the cabinet and outlets are in the back of the cabinet. Allow

clearance in front of and in back of the cabinet for proper air circulation. The clearances required around the

ITCs are shown in Table 3-2.

The basic environmental requirements for operation of the ITC are:

- Recommended Operating Range: 15–25C (59–77F)

- Maximum Relative Humidity: 95%, noncondensing

The ITC cooling requirements are shown in Table 3-3.

Table 3-1. ITC Weights

Model

Weight

kg (lb)

Shipping Installed Point Loading

Eaton 93E 30ITC with Input Transformer 250 (551) 225 (496) 8 at 28 (62)

Eaton 93E 30ITC with Input and Output Transformer 403 (889) 378 (834) 8 at 47 (104)

Eaton 93E 60ITC with Input Transformer 450 (993) 416 (918) 12 at 35 (77)

Eaton 93E 60ITC with Input and Output Transformer 690 (1521) 656 (1446) 12 at 54 (120)

Table 3-2. ITC Clearances

From Top of Cabinet 304.8 mm (12") working space

From Front of Cabinet 914.4 mm (36") working space

From Back of Cabinet 914.4 mm (36") working space

From Right Side of Cabinet None Required

From Left Side of Cabinet None Required

Table 3-3. Cooling Requirements During Full Load Operation

Rating Transformer Voltage Heat Rejection

Model kVA Type Input Output Watts BTU/hr x 1000 Kg-cal/hr

Eaton 93E 30ITC with Input Transformer 30 Input 480 208Y/120 2350 8.0 2022

Eaton 93E 30ITC with Input and Output Transformer 30

Input 480 208Y/120

3486 11.9 2999

Output 208 480Y/277

Eaton 93E 60ITC with Input Transformer 60 Input 480 208Y/120 2289 7.8 1970

Eaton 93E 60ITC with Input and Output Transformer 60

Input 480 208Y/120

5274 18.0 4538

Output 208 480Y/277

Page is loading ...

Eaton 93E 30ITC, 93E 60ITC Installation guide

Related papers

Other documents