Black Box QCE42U Datasheet

Brand: Black Box

Model: QCE42U

Category: Racks

Type: Datasheet

This manual is also suitable for

QCE12U

Black Box QCE42U is a cabinet designed to provide a quiet and secure environment for sensitive electronic equipment. It features a heavy-duty steel frame and thick acoustic foam insulation that reduces noise levels by up to 25 decibels. The QCE42U has a spacious interior with 42 rack units of mounting space, making it ideal for housing a variety of equipment, including servers, network switches, and telecommunications gear. The cabinet is also equipped with a built-in fan system that helps to circulate air and prevent overheating.

Black Box QCE42U is a cabinet designed to provide a quiet and secure environment for sensitive electronic equipment. It features a heavy-duty steel frame and thick acoustic foam insulation that reduces noise levels by up to 25 decibels. The QCE42U has a spacious interior with 42 rack units of mounting space, making it ideal for housing a variety of equipment, including servers, network switches, and telecommunications gear. The cabinet is also equipped with a built-in fan system that helps to circulate air and prevent overheating.

Instructions for Removing a QuietCab Elite

™

Cabinet from a Pallet Using a Forklift Truck

1. Make sure the pallet is placed on a flat, even surface.

Remove the straps and then the sides from the crate

(use a mallet). Leave the bubble-wrapped cabinet on

the pallet.

CAUTION: A forklift must be used by a

trained driver to safely remove the cabinet

from the pallet.

2. To remove the cabinet from the pallet, make sure the

forklift is facing the front or rear of the cabinet (not the

sides). Carefully place forks through the aperture

underneath the frame. Gently lift away from the pallet,

making sure the cabinet is properly balanced on the forks.

CAUTION: Toppling hazard! A person should stand on each

side of the cabinet to help balance it during lifting.

3. Gently lift away from the pallet, making sure the cabinet

is properly balanced on the forks.

Instructions for Removing a QuietCab Elite Cabinet

from a Pallet without Using a Forklift Truck

1. Make sure the pallet is placed on a flat, even surface.

Remove the straps and then the sides from the crate (use

a mallet). Leave the bubble-wrapped cabinet on the pallet.

2. While the cabinet is still on the pallet, remove the

packaging and bubble wrap. The cabinet is heavy, so

remove the front and rear doors and the side panels.

CAUTION: Make sure the doors and side panels are placed

against a solid wall on a clean, even surface after

removing them from the cabinet.

3. Once all the cladding has been removed, the frame should

be light enough for 2 or 3 people to lift it off the pallet.

NOTE: Place the frame where you want it to remain before

replacing the cladding.

724 -746 -5500 | blackbox.com

BL A C K B OX

®

QCE12U

QCE24U

QCE42U

© Copyright 2012. Black Box Corporation. All rights reserved. Black Box and the Double Diamond logo are registered trademarks, and Elite is a trademark, of BB Technologies,

Inc. Any third-party trademarks appearing in this document are acknowledged to be the property of their respective owners.

1

Black Box QCE42U Datasheet

Brand: Black Box

Model: QCE42U

Category: Racks

Type: Datasheet

This manual is also suitable for

QCE12U

Black Box QCE42U is a cabinet designed to provide a quiet and secure environment for sensitive electronic equipment. It features a heavy-duty steel frame and thick acoustic foam insulation that reduces noise levels by up to 25 decibels. The QCE42U has a spacious interior with 42 rack units of mounting space, making it ideal for housing a variety of equipment, including servers, network switches, and telecommunications gear. The cabinet is also equipped with a built-in fan system that helps to circulate air and prevent overheating.

Download PDF

Related papers

Other documents