OPCOM OFG003-3 User manual

Ver.: 202006

E. Maintenance

F. Troubleshooting

Checkpoints / Solution

Make sure all power cables are connected.

Power button is ON.

Make sure LED status is ON

If it is on HI or LOW mode, the lamp has off time, during 24-hour cycle.

Pump may make a buzzing sound in the beginning due to air inside the pump. After a minute with

water running through the pump, this sould be reduced.

Control Box is designed with Auto, HI and LOW modes, which turn the lamps and the pump on and off

periodically. It simulates an outdoor daily cycle to offer the best growing condition

Rotate the ring at the end of the pump clockwise or counterclockwise to get the most suitable water flow

Make sure it is not clogged at the water flowing gateway on each planting layer

Issue

Lamps not

lighting up

Pump has a

buzzing sound

The lamp/ pump

stop Safter hours

Water Over flows

F1. Add Water

1. Measure the pH/EC value every 1-2 weeks and add water to maintain the vlaue balance

F2. Change Water

1. After a cycle of planting, change the water and clean the unit.

2.When changing water, clean water gateway on each planting layers, you may also add moss

detergent in the water tank to avoid the moss remaining

(fig 1 )

3. On the regular basis of every 1-2 weeks, clean the filtering sponge in the pump

1. Keep the electrode clean of EC meter and cover the electrode protective cap when not in use.

2. Turn off the meter when not in use for an extended amount of time.

F3. EC Meter Use and Calibration

www.opcomfarm.com

For more information, please visit

F1708038 P17103002

P17092804

F1709051

PATENT

Intertek

USC

4010499

G. Installation steps of water pump

D. Optional Accessories

1. Black Cloth Cover

(Fig1)

Manual

Grow Wall3

Hydroponics Grow Wall 3

1. As shown in the picture:

prepare the backup pump.

4. Plug in DC jack 5. Pump replacement is

completed as shown in the tank

3. Connecting control valve

2. Insert the upper water pipe

into the water tank inlet

2. Anti Insect Net 3. 500W Water Auto Heater

Please read and follow every steps to avoid any malfunction.

B2.Young Plant Stage

1. Add 10.5 gallons water to the water tank.

2. During Young Plant Stage, turn on LED and Pump . Please refer to the ChartII.

3. Add adjustment into the water tank and ensure EC value between(=1.0-2.0mS/cm)

4. Ensure pH between 5.5-6.5 (adjust by pH+/-). For EC& pH adjustment instruction, please

refer to following Chart at below.

B3. Growing Stage

B. Seedling

Status

NT-Adjuster

0.0-0.5

Add Ax2

0.5-1.0

Add Ax1

1.0-1.5

Standard range

over 2.0

Add water

Satus

Adjustment+

Adjustment-

4.0-4.5

Add Bx0.5

4.5-5.0

Add Ax2

5.0-5.5

Add Ax1

5.5-6.5

Standard range

6.5-7.0

Add Bx0.5

7.0-7.5

Add Bx1

lortnoc hctiws ,thgieh sehcni 2 revoot worg stnalp

nehW .1 box to auto mode. Please refer to Chart II

2. After 4-6 weeks, harvest the larger plants for consumption and keep smaller plants growing.

3. For time saving, sow the new seeds in sprout tray one week before you start next planting process.

1. Before you start next seedling, take advantage of the seedling tray for sprouts and microgreens. It takes 7-10 days to harvest.

2. Put seeds in warm water(recommeded temperature is 95 , not over 104 ) for 24 hours.

3. Cover the sponges with wet paper towels.

4. Place the seedling tray with cover in the shade or cover it with black cloth.

5. After germination, during the growing stage, keep green sprout under the light and white sprout in the shade or cover it

with black cloth; in 7-10 days, you can harvest.

Day 7-10Day 0 Day 1

Green sprout White sprout

Chart II: Plant Stage

Basil, Lemon Balm

Germination Stage

Planting Time

Day 0~7

LED Mode

N/A

Pump Mode

N/A

Notes

* For your expected plant amount, you can refer to the sprout rate of 1st planting cycle.

* If you need more planting information, please vist to www.opcomfarm.com and read “Plant Q&A”.

Nourishment

N/A

T ( )

68 - 77

80%

0.5-1.0

5.5-6.5

Young Plant Stage Day 3~14 ON ON NT-Starter 59 - 86 45%-70% 1.0-2.0 5.5-6.5

Growing Stage After Day 14 Auto Auto NT-Adjuster 59 - 86 45%-70% 1.0-2.0 5.5-6.5

Be sure each sponge is fully wet in

seedling tray.

* Please keep the seeds in refrigerator if you don’t use it, recommended temperture is 41 -50.

(Fig4)

(Fig3)

This side up!

(Fig2

(Fig1

1. Add water to the seedling tray, up to the water (red) level.(Fig1)

2. First time sprout: just open the seedling box and add water. Then go to step 4. (Fig 1)

3. Second time sprout: Open Grow Sponge package,put each sponge piece into water of seedling tray

(make sure the front side with the seed label is side up), press the sponges into water 5 seconds and

ensure the sponges absorb water completely. Put seed moisturizing cover on the sponges.(Fig2)

4. Place the seedling tray with cover in the shade.(Fig3)

5. Suggest using Watering Spray water to sponges and keep them wet everyday.

6. During 0 ~ 7 days, find the sprouted ones in the tray; pick them out, and move them into product (make

sure the sponges lineup with the black dot on the partition)(Fig4) and to next stage: B2. Young Plant Stage.

7. Discard unsprouted sponges after regular germination time.

8. In each sponge, keep strong plants and cut the other weak plants.

* Different plant may have different germination time, please check before plant.

B1. Germination Stage

C. Sprouts and Microgreens.

Grow Wall3

A. Assembly

A1. Remove all the parts from box and check all the accessories

Chart I: Control Box Mode

LED Growth Light x5pcs

Control Box x 1pc

Wall Mount Brackets x 2pcs

Base Stand x2pcs

Planting tray x5pcs

Hose x 1

Seedling Tray x2pcs

(665*175*65mm)

Grow Kits

Warranty Card Quick Guide Manual

Grow Sponge 60pk

x4pcs

EC Meter

x1pc

pH test

paper x1pc

Accessories Manual

Cleaning

ponge x1pc

Water

Spray x1pc

Remote

Controller x 1pc

Grow Sponge For

Green Lettuce 60pk

x3pcs

Grow Sponge 3x60pk

(OASS006 For Basil)

Grow Sponge For

Red Leaf Lettuce 60pk

x3pcs

Quick Guide Manual

Grow Wall3

Hydroponics G reen Wall3

maple plank x6pcs

Tube(2) x 1

Tube(1) x 4

Pump x 2pcs

(Backup pump x 1)

Expansion Anchor Bolts x4pcs

Wall-Mount Screws x4pcs

Ribbon x10pcs

Screwdriver

Cross-Head x1pc

Filter Sponge

x10pcs

A2. Assemble GrowWall3

1. Assembly

L1, L2, R1, R2 columns are fixed to L1 planting grooves with column screws. (Fig1.2.3)

L2, L3, R2, R3 columns are fixed to L2 grooves with column screws, follow this step until

the L5 grooves assembly is completed. (Fig4)

Unfasten the L6, R6 column fixed to the beam assembly and connect the previously

installed assembly B13. (Fig.5)

The side column is assembled with the main line.

Put LED light in the center of each layer, slide along the magnets on both sides to adjust

the height of LED. Three positioning heights to meet the lighting needs of

different grow stages of plant, and also to achieve the purpose of power saving.(Fig6.)

insert the ligh line linto the power interface of the side column.

(Fig7.)

11 Place the motor pack in the water tank and connect the fan power line on the right (Fig13)

The upper water pipe is passed through the hole of the L6 column, and the hose passes through

the hole from the upper to the lower to the L1 column. (Fig9.10)

Insert three maple planks from the side column in turn (the right L 3 maple plank is fixed with

the crossbeam part). (Fig8)

And a lower water pipe is arranged according to the opening hole of the planting groove. Fig11

Install the wall mount bracket on the top of the beam and stand up the product.(Fig12)

2. Water Line Set Up

3. Electric Line Set Up

4. Other Installations

5. LED light Control

Thank you for purchasing OPCOM Farm GrowWall3, the indoor hydroponics growing system. lt is designed for easy to use and

efficient growth by one-touch AUTO mode.lt holds up to 80 plants capacity. Please read the quick guide carefully before setting it up.

For detailed user guide video, please visit GrowWall3 page at http://www.opcomfarm.com

A spoon=1g / B spoon=5g / C spoon=10g

4-6 weeks

Harvest

Cut off Large leaf

1 week

Keep

for regrow

Soda (pH+)

50ml x1

Salt #1 (Nutrition)

250ml x2

Lemon(pH-)

50ml x2

Select your color of LED light - There is a switch in the right side of the LED light.(Fig19) You can select the color manually by pressing the switch. We have white light

the control box can only control the time of LED On or LED OFF, the color of LED light need to control manually.

The height of LED light - You can decide the height of the LED light depending on your needs. Please note that the closer the light to the plants the higher the temperature is.