Robertshaw 41-311 (WRC23-K) Ignitor Kit User manual

Brand: Robertshaw

Model: 41-311 (WRC23-K) Ignitor Kit

Type: User manual

INSTALLATION DATA

41-311 (WRC23-K)

IGNITOR KIT

Customer Service Telephone 1.800.304.6563

Customer Service Facsimile 1.800.426.0804

[email protected]

Robertshaw®, Ranco®, Paragon® and Uni-Line® are

trademarks of Robertshaw, its subsidiaries and/or

affiliated companies. All other brands mentioned

may be the trademarks of their respective owners.

For Technical Service

Telephone 1.800.445.8299

Facsimile 1.630.260.7294

[email protected]

www.uni-line.com

www.robertshaw.com

12/14 – WRC23K-IS Rev C

THIS IGNITOR MAY OR MAY NOT BE IDENTICAL TO THE IGNITOR BEING

REPLACED. FOLLOW INSTRUCTIONS WITH PICTURE OF THE IGNITOR

BEING REPLACED.

To Replace Round lgnitor

1. REMOVE CORD FROM OUTLET.

2. Remove lower front toe panel.

3. Shutogas.

4. Unscrew union.

5. Remove burner base from cabinet base - keep screws.

6. Remove the WHITE (F52) wire and the BLUE (FS1) wire from

the sensor.

7. Pull apart the connectors with the BLUE and BLACK wires coming

from the gas valve to the cabinet wiring harness.

8. Remove burner assembly from the dryer.

9. CutoBLACKandREDwirestwoinchesbackfrombracket.

10. Remove and throw away failed ignitor and bracket. Keep the screws.

11.StripinsulaonfromtheBLACKandREDwires3/8”from

cut end.

CAUTION

HANDLE REPLACEMENT IGNITOR WITH CARE - FRAGILE.

Check for gas leaks by using soap and water on the

threadsoftheunion.Donotuseamatchorameof

any kind.

Keepallwiresawayfromtheburnerameorignitorwhen

reassembling the burner to the cabinet base.

12. Mount the replacement ignitor and bracket assembly to the

 burnertube,reusingtheNo.10-16x1/2”screw,fromstep10.

13.Cutotheconnectoronthereplacementignitorandstrip

 insulaon3/8”fromend.

14. Using one of the wire nuts supplied, put the RED wire from the

burner assembly and one of the WHITE wires from the replacement

ignitor to gether. Then connect the BLACK wire from burner and

other WHITE wire from ignitor with remaining wire nut.

To Replace Flat lgnitor

1. REMOVE CORD FROM OUTLET.

2. Remove lower front toe panel.

3. Shutogas.

4. Unscrew Union.

5. Remove burner base from

cabinet.

6. Remove the WHITE (FS2) wire and

the BLUE (FS1) wire from the sensor. Remove and

throw away failed ignitor and

7. Pull apart the connectors with the BLUE and BLACK wires coming

from the gas valve to the cabinet wiring harness.

8. Remove burner assembly from the dryer.

9. Pull apart the connectors between the gas valve and the ignitor.

10. Remove and throw away failed ignitor and bracket. Keep the screw.

11. Mount the replacement ignitor and bracket assembly to the burner

 tube,reusingtheNo.1016x1/2”screw,menonedinstep10.

12. Reassemble in reverse order.

REMOVE & THROW AWAY

OLD IGNITOR & BRACKET

TO SENSOR

(Step 6)

WHITE

BLUE

BLACK

TO CABINET

WIRING HARNESS

(Step 7)

GAS VALVE KNOB

(Step 3)

UNION

(Step 4)

SCREWS

(Step 5)

RED

BLACK

CUT OFF HERE AND STRIP BACK

IF REPLACING ROUND IGNITOR

CUT OFF HERE AND STRIP BACK

IF REPLACING ROUND IGNITOR

DISCONNECT PLUG IF

REPLACING FLAT IGNITOR

Robertshaw 41-311 (WRC23-K) Ignitor Kit User manual

Robertshaw 41-311 (WRC23-K) Ignitor Kit User manual

Robertshaw 41-311 (WRC23-K) Ignitor Kit User manual

Related papers

Other documents