Aiphone MYW-P10L Operating instructions

Aiphone
Brand
Aiphone
Model
MYW-P10L
Category
Door intercom systems
Type
Operating instructions
- INSTRUCTIONS -
MYW-P10L
10 Camera Adaptor for LEF/LDF System
Special
Order
Products
WIRING DIAGRAM:
Pg. 1
The MYW-P10L adaptor allows up to 10 2-wire video door stations to be used with the LEF series Master
Sentry System. MY or MK PanTilt series video door stations may be used with the MYW-P10L. CCTV
cameras may be connected through the MYW-P10L using the MYW-MD/B adaptor. Door release is
available through the intercom system (LEF or LDF only).
NOTES:
1. The MONITOR button,
Auto-Scan Duration, and
Monitor Receive Volume
switches on the front of the
unit are non-functional.
2. Diodes shown must be
used when using RY-PA door
release relays. They are
1N4007, and are included in
the box with the unit.
3. Only wiring concerning the
MYW-P10L is shown here. For
complete installation and
wiring information, please see
the standard LEF instructions.
0804
MK-DAC
RY-PA
RY-PA
RY-PA
RY-PA
Yellow
Yellow
Yellow
Yellow Black
Black
Black
Black
To Strike
& Power
#1
To Strike
& Power
#2
To Strike
& Power
#3
To Strike
& Power
#4
Yellow Black
To Strike
& Power
#5
RY-PA
MK-DAC
MK-DBC
MK-DBC
MK-DGC
Any MK-series
video door station
is compatible with
this system.
B1 1A1
B2 1A2
2A1
U1 2A2
U2
3A1
3A2
+18V
-18V 4A1
4A2
5A1
5A2
~
10A1
10A2
1
2
3
4
5
6
7
8
9
10
E
+12V
-12V
K1
K2
K3
K4
K5
~
K10
MYW-P10L
A1
A2
A1
A2
A1
A2
A1
A2
A1
A2
1
2
3
4
5
6
7
8
9
10
C
E
R
Y
+
-
L
K1
K2
K3
K4
K5
~
K10
1
2
3
4
5
6
7
8
9
10
C
E
R
Y
+
-
L
K1
K2
K3
K4
K5
~
K10
LEF-10
LEF-10
+
-
PS-1225UL
A1
A2
B1
B2
U1
U2
+
-
B1
B2
A1
A2
U1
U2
+
-
MYH-CU
MYH-CU
+
-
PS-1820UL
INSIDE MYW-P10L CHASSIS
EXTERNAL TERMINAL BLOCK
MYW-P10L TERMINAL DEFINITIONS:
Found inside MYW-P10L
nA1 Input from MY/MK Series
nA2 video door station
B1 Video signal output
B2 to monitors
U1 Video activation
U2 to monitors
18V+ Positive 18V DC
18V- Negative
N1,N2 Unused
Found in external terminal box
1 ~ 10 Audio communication
E Common communication
12V+ Positive 12V DC
12V- Negative
K1 ~ K10 Video control terminals
OPERATION:
Call-in from a video door station:
1. When a video door station calls in, all monitors in the system will activate, and the appropriate LED will illuminate
on the LEF master. The call tone will be heard until the call is answered or for 5 seconds, whichever comes first.
The monitor will turn off in 45 seconds if the call is not answered. The LED will remain lit for approximately 20
seconds after the tone is no longer heard.
2. While the monitor is active, the PanTilt button may be used to control the camera position (PanTilt cameras only.)
3. If the door is not selected within 45 seconds, the monitor will turn off. Communication and video can be
established by pressing the appropriate selector button on the LEF master.
4. When called by a door station while communicating, only the LED will activate. Press the OFF button to
end the existing conversation, then select the door button to establish communication and video.
Monitoring a door station:
1. On the LEF master, press the selector button of the door that you wish to monitor.
2. Video monitor will turn on showing the selected door, remaining active for approximately 2-1/2 minutes.
3. Communicate with the door using the LEF master station.
4. Press the OFF button on the LEF master to end the conversation.
Initializing the system:
If the MYW-P10L is used with CCTV cameras and MYW-MD/B's, the unit must be initialized before operation.
To initialize the system:
1. Turn power switch on the MYW-P10L OFF.
2. Turn switches associated with CCTV camera locations to ON position.
(For example if stations 4, 5, 6 are
CCTV cameras, set switches 4, 5, and 6 to ON.)
3. Turn MYW-P10L power switch to ON.
4. Wait for red STANDBY light to go out.
(STANDBY light is located on the face of the unit.)
5. Turn switches associated with the camera locations back to the OFF position.
6. The system is now operational.
Pre-Tone On/Off
When a door station is selected, a short pre-tone will be heard. This pre-tone can be turned off:
1. Remove top left cover of MYW-P10L.
2. Move the second switch from the left to the OFF position.
Reset switch
If the MYW-P10L malfunctions, press the reset switch located under the top left coverplate of the MYW-P10L.
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
(425) 455-0510
FAX (425) 455-0071
Toll Free Technical Support:
1-800-692-0200
FAX: 1-800-832-3765
E-mail: [email protected]
Pg. 2
MYW-P10L/A Instr.
0804bkjs
SPECIFICATIONS:
Power Source: 18V DC. Use PS-1820UL for every 3 video components.
Calling: Electronic call tone and LED on LEF master. Call tone remains active for 5 seconds. LED
remains activated for 25 seconds, or until the call is answered, whichever comes first.
Monitors stay activated for 45 seconds.
Monitoring: Select door station to monitor using LEF master.
Monitors are active for 2-1/2 minutes.
Wiring Distance: MYW-P10L to MK series Video door station: 330' using 18 AWG
MYW-P10L to farthest MY series monitor: 245' using 18 AWG
MYW-P10L to farthest LEF-10: 650' using 22AWG; 1600' using 18AWG
Dimensions (HxWxD): 4-1/2" X 7-11/16" X 9"
Weight: 3.31 lbs. (Approx.)
Off
On
Off
10
8
9
7
6
5
1
2
3
4
Set switches located inside bottom of unit.
  • Page 1 1
  • Page 2 2

Aiphone MYW-P10L Operating instructions

Aiphone
Brand
Aiphone
Model
MYW-P10L
Category
Door intercom systems
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents