Aiphone MYW-MD Operating instructions

Brand: Aiphone

Model: MYW-MD

Category: Door intercom systems

Type: Operating instructions

- INSTRUCTIONS -

The MYW-MD adaptor converts the video from a 2-wire signal to a standard coaxial video signal

(Demodulator mode). It can also be used to convert a standard CCTV camera's signal to a 2-wire signal,

compatible with Aiphone's MY series video monitors (Modulator mode).

MYW-MD

Video Modulator/Demodulator for MY series Video Systems

MYW-MD TERMINAL DEFINITIONS:

MODULATOR:

MA1 2-Wire output to

MA2 MY monitor/adaptor

MV+ Coax input: center cond.

MV- Coax input: Braided shield

+ Positive 18V DC

- Negative

Input signal requirements:

75 ohm, 1V peak-to-peak.

Coax: Solid copper core with copper braid.

DEMODULATOR:

DA1 2-Wire input from

DA2 MY monitor/adaptor

DV+ Coax output: center cond.

DV- Coax output: Braided shield

+ Positive 18V DC

- Negative

Output signal:

75 ohm, 1V peak-to-peak.

Coax: Solid copper core with copper braid.

Special

Order

Products

MODULATOR

MYW-MD to integrate a Standard CCTV camera with an Aiphone Monitor

*MYW-MD Can also be used with:

MY-1CD

MY-CU

MYW-P1L

MYW-P3L (input only)

Center cond. to MV+

Braid to MV-

CCTV Camera

75 Ohm, 1V Peak-to-peak

(Independently powered)

1A1

1A2

2A1

2A2

MY-2CD*

MY-DC

MA1

MA2

MV+

MV-

MYW-MD

PS-18C

Polarized

JUMPER CLIP: (Located under rubber cover in upper right corner of the faceplate of the MYW-MD)

Set in Modulator (top) position from factory.

Ensure that jumper clip is

between the top two pins.

Pg. 1

Center cond. to MV+

Braid to MV-

CCTV Camera

75 Ohm, 1V Peak-to-peak

(Independently powered)

Center cond. to MV+

Braid to MV-

CCTV Camera

75 Ohm, 1V Peak-to-peak

(Independently powered)

MA1

MA2

MV+

MV-

MYW-MD

Polarized

MODULATOR

Master Sentry Intercom and Video System with Standard CCTV Cameras

MYW-P3L

MY-DC

PS-18C

MA1

MA2

MV+

MV-

MYW-MD

Polarized

1A1

1A2

2A1

2A2

12+

12-

EL2

18+

18-

3A1

3A2

18+

18-

MYH-CUB*

12+

12-

K10

LEF-10C*

LE-DA*

NOTES:

1. In the above system example, the CCTV

cameras are addressed by pressing the

MONITOR button on the MYH-CUB. Press once

to turn on camera 1 (MY-DC), press again to

switch to camera 2 (CCTV #1), pressing

MONITOR a third time will switch to Camera 3

(CCTV #2) and a fourth time turns the monitor

off.

2. The LE-DA will become active by selecting

station #9 on the LEF-10C. Selecting this

station will also activate CCTV camera #2. The

camera will not activate when the LE-DA calls

in.

System Configurations:

1 Aiphone video door station and 2 CCTV cameras

2 Aiphone video door stations and 1 CCTV camera

Optional:

Part #261380 - Video Output connector for MYW-P3L.

(Provides a 1V peak-to-peak video signal output.)

ONLY WIRING RELATING TO THIS APPLICATION

IS SHOWN HERE. SEE PRODUCT INSTRUCTIONS

FOR COMPLETE WIRING INFORMATION.

JUMPER CLIP: (Located under rubber cover in upper

right corner of the faceplate of the MYW-MD)

Set in Modulator (top) position from factory.

Ensure that jumper clip is

between the top two pins.

Separate video cable from

intercom cable

* Any LE or LS series

door station may be used.

* Any 5 or 10 call LEF

series master can be

used.

* Use MYH-CU for surface

mount applications.

Pg. 2

DEMODULATOR

MYW-MD used for VIDEO OUTPUT with Aiphone MY series Video Entry Systems

The picture from the Video Door Station can be seen at standard monitors whenever the Aiphone system

is activated.

MY-1CD

JUMPER CLIP: (Located under rubber cover in upper

right corner of the faceplate of the MYW-MD)

Move to Demodulator (lower) position.

Coax output to standard video

input. (CCTV monitor, RF

modulator, or into cable

distribution network through a

multiplexer.)

* Used for video OUTPUT with

MY-1CD, MY-CU, MYW-

P3CB MYW-P1L, and MYW-

P3L.

DEMODULATOR

MY Video Door Station with Standard Monitor (No audio communication or PanTilt capabilities)

MY-DC

Polarized

DA1

DA2

DV+

DV-

MYW-MD*

Red

Blk

PS-18YC/A

Center cond. to DV+

Braid to DV-

MY-DC*

DA1

DA2

DV+

DV-

MYW-MD*

PS-18C

Center cond. to DV+

Braid to DV-

IMPORTANT:

CN2 speaker microphone connector inside

Aiphone Video door station must be

unplugged to prevent the possibility of

feedback.

To standard monitor

or monitor input on a

video switcher.

Ensure that jumper clip is

between the bottom two pins.

JUMPER CLIP: (Located under

rubber cover in upper right corner

of the faceplate of the MYW-MD).

Move to Demodulator (lower)

position.

Ensure that jumper clip is

between the bottom two pins.

TO POWER THE CAMERA:

(1) WHEN IN USE

- Install a switch or relay contact in series with the "+" terminal from the power supply (see diagram.)

- Solder a jumper between points labeled AA on the MYW-MD main PC board. (see Illustration)

This allows the camera to be activated manually, or when the relay contact is activated from a separate source.

(2) CONTINUALLY

- Solder a jumper between points labeled AA on the the MYW-MD main PC board. (see Illustration)

This will provide continuous power to the camera, which may cause the camera to be warm.

Note: Continually powered, the overall life of the camera will be reduced and condensation may occur.

Solder jumper

wire between two

holes in land

pattern.

Solder side

view of PC

board.

1A1

1A2

*Any MY

series camera

can be used

Standard 9"

Monitor

Pg. 3

IMPORTANT:

Modulator Deviation Control: Contrast control located underneath the cover in the upper right corner of the unit.

This applies only when the MYW-MD is used with a CCTV camera. To adjust the picture for more contrast, turn the

variable resistor clockwise with a small screwdriver.

OPERATIONS

MODULATOR:

Using the MODULATOR to Integrate a CCTV camera with an Aiphone 2-wire video system:

1. The view from the CCTV camera can be seen on the Aiphone MY monitor by pressing the MONITOR button. With

multi-camera systems (MY-2CD, MYW-P3CB & MYW-P3L), the cameras will come up sequentially. (e.g. One

press of MONITOR button brings up camera 1, second press brings up camera 2.) After the last camera in the

system is activated, the next press of the MONITOR button will turn off the monitor. If the monitor is left on, it will

automatically time out after 2-½ minutes.

2. When using a CCTV camera with the LEF/MY system, an audio sub station can be installed near the camera to

provide both audio and video monitoring. The station is activated simultaneously from the LEF master

station through the proper connection of the "K#" terminal of the master to the MYW-P3L adapter.

DEMODULATOR:

Using the Demodulator for VIDEO OUTPUT with the Aiphone 2-wire video systems:

1. When the call button is pressed on the MY door station, the inside monitor station will ring and the picture will

come on. At that time, the video signal out of the MYW-MD adaptor will be present, and the picture can be seen

on the remote monitor.

2. When the MONITOR button on the inside Aiphone station is pressed, the picture will come up for approximately

2-½ minutes and video signal sent to the monitor via the MYW-MD.

3. The video signal can be connected to any receiving device that accepts a composite video signal (75 ohm, 1V

peak-to-peak). This could be a standard CCTV monitor, a video input on a switcher or a multiplexer

system that modulates the video onto a cable TV channel. To take the video signal directly into a TV,

use a spare video input or go through an RF modulator.

Using the Demodulator to integrate the MY video door station with a standard CCTV monitor:

(No audio communication or PanTilt is possible with this application)

1. To view the camera location at any time, the camera must be powered at all times, or a switch must be installed

to turn it on. To do this, the PC board must be modified by adding a jumper wire in the location indicated on

the wiring diagram on page 3.

2. There is no PanTilt control of the camera when used in this application. To adjust the angle of the MY-DC at the

time of installation, remove the Lexan® dome and move the camera head to the desired angle. Replace the

dome and install the unit. If an MY-CA video door station is used, the camera view will be centered and is not

adjustable.

3. If the camera is powered continually, there will always be a video output from the MYW-MD. There is no audio

communication possible through the door station. This application will shorten the life of the camera.

SPECIFICATIONS:

Power: 18V DC. Use Aiphone model PS-18C (or PS-18YC/A with MY-1CD)

Current consumption: 100mA as Modulator; 500mA as Demodulator

Wiring distance: ALL DISTANCES ARE USING 18 AWG WIRE

Modulator: Max. 330' from MYW-MD to MY Monitor/adaptor

Demodulator: Max. 30' from MY monitor when used for video output

Max. 330' from MY door station when used with a standard monitor

Power supply: Max. 16' to MYW-MD

Dimensions: 5-1/2"H x 3"W x 1-1/2"D

COAXIAL CABLE: 75 ohm, copper center conductor, copper braid, 95% coverage.

DC resistance: Max, 15Ω per 1000 feet.

Aiphone Communication Systems

1700 130th Ave. N.E.

Bellevue, WA 98005

(425) 455-0510

FAX (425) 455-0071

Toll Free Technical Support:

1-800-692-0200

FAX: 1-800-832-3765

E-mail [email protected]

Pg. 4

MYW-MD Instr.

1198bkjd

Aiphone MYW-MD Operating instructions

Brand: Aiphone

Model: MYW-MD

Category: Door intercom systems

Type: Operating instructions

Download PDF

report

Aiphone MYW-MD Operating instructions

Aiphone MYW-MD Operating instructions

Related papers

Other documents