2. Axxess
  3. CHT0-01

Axxess CHT0-01 Installation Instructions And Owner's Manual

  • Hello! I am an AI chatbot trained to assist you with the Axxess CHT0-01 Installation Instructions And Owner's Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Installation instructions for CHTO-01
METRA. The World’s best kits.™
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
• Providesaccessory(12-volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinamplified,non-amplifiedsystems,ordigitalamplifiedsystems
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• ASWC-1harnessincluded(ASWC-1soldseparately)
• Adjustablegaincontrolforoverallvolume(onamplifiedsystems)
• Retainsblindspotdetectionsystem(ifequipped)
• Highlevelspeakerinput
• Micro“B”USBupdatable
• Retainsbalanceandfade
KIT FEATURES
• Cuttingtool•Tape•Crimpingtool•Connectors
(example:butt-connectors,bellcaps,etc.)
TOOLS REQUIRED
Chrysler vehicles
2004-2010
CHT O-01
APPLICATIONS
See inside front cover
• CHTO-01Interface•16-pinharnesswith
strippedleads•10-pinharnessto22-pinChrysler
harnesswithstrippedleads•4-pinharnesswith
strippedleads
INTERFACE COMPONENTS
CHTO-01
2
Applications
CHRYSLER
300 2005-2007
Aspen 2007
DODGE
Caliber 2007-2008
Charger 2006-2007
Dakota 2005-2007
Durango 2004-2007
Magnum 2005-2007
Ram1500 2006-2008
Ram2500/3500 2006-2009
JEEP
Commander 2006-2007
Compass 2007-2008
GrandCherokee 2005-2007
Patriot 2007-2008
MITSUBISHI
Raider 2006-2007
From the 16-pin harness
• Connectthe(2)Redwirestotheignition/accessorywireoftheaftermarketradio.
• ConnecttheOrange/Whitewiretotheilluminationwireoftheaftermarketradio.Iftheaftermarketradio
doesnothaveanilluminationwire,tapeofftheOrange/Whitewire.
• ConnecttheBlue/Whitewiretotheampturnonwireoftheaftermarketradio.
• TapeuptheBrownwire.Itwillnotbeusedinthisapplication.
For vehicles with built-in navigation (only), make the following connections:
• ConnecttheLight Green wiretotheparkingbrakewireoftheaftermarketnavigationradio.
• Connectthe Blue/Pink wiretotheVSSorspeedsensewireoftheaftermarketnavigationradio.
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio.
Only make the following connections if the vehicle is amplified:
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputoftheaftermarketradio.
• ConnecttheWhite/Black wiretotheleftfrontnegativespeakeroutputoftheaftermarketradio.
• ConnecttheGraywiretotherightfrontpositivespeakeroutputoftheaftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputoftheaftermarketradio.
Continued on next page
Connections to be made
CHTO-01
3
Connections to be made
• ConnecttheGreen wiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Black wiretotheradio’sleftrearnegativespeakeroutput.
• ConnectthePurplewiretotheradio’srightrearpositivespeakeroutput.
• ConnectthePurple/Blackwiretotheradio’srightrearnegativespeakeroutput.
From the 22-pin Chrysler harness
• Connectthe Yellowwiretotheradio’s12-voltbatteryormemorywire.
• Connectthe Blackwiretotheradio’sgroundwire.
• ConnecttheBlue/Whitewiretotheradio’sampturnonwireifpopulatedon
thefactoryside.
For non-amplified vehicles (only), make the following connections:
• Disconnectthe(2)4-pinconnectors,withthePurpleandGreen wiresinit.
• Connectthe4-pinharnesswithstrippedleadstothe4-pinconnector,with
thePurpleandGreenwires,comingfromtheGray22-pinconnector.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• ConnectthePurplewiretotheradio’srightrearpositivespeakeroutput.
• ConnectthePurple/Blackwiretotheradio’srightrearnegative
speakeroutput.
Tip: If you are unsure if your vehicle is amplified or not, note that these following
wires will only be populated in the factory harness if non-amplified.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Blackwiretotherightfrontnegativespeakeroutputof
theaftermarket.
From the 12-way harness
• ThisharnessisfortheASWC-1(soldseparately).PleaserefertotheASWC-1
instructionsforprogramming.
Continued on next page
Installation instructions for CHTO-01
METRA. The World’s best kits.
™
• Withallconnectionscompletedtotheaftermarketradio,plugthe22-pinharnessintothevehicles
wiringharness.
• Reconnectthenegativebatteryterminal.
• Cyclethekey,byturningtheignitiononfor30seconds.Thenoffandonagaintotesttheradio.
Installing the CHTO-01
• Turntheignitiononifnotalready,andthenturntheradioontoverifythattheradioworks.Check
balanceandfadercontrolsforproperoperation.
For amplified models only:
• Toadjusttheoverallvolumeofyouraudiosystemrotatethepotentiometer,whichislocatedonthe
16-pinsideoftheinterfaceclockwise.
Testing the CHTO-01
Our installation parts and kits make aftermarket stereo and video installation a breeze.
/