Metra Electronics XSVI-5524-NAV User manual

Type
User manual
INSTXSVI-5524-NAV
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 4/29/14
INSTXSVI-5524-NAV
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 4/29/14
INSTXSVI-5524-NAV
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 4/29/14
INSTXSVI-5524-NAV
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 4/29/14
XSVI-5524-NAV
Ford accessory and NAV output CAN harness 2011-up
• Providesaccessory(12volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinnon-amplifiedsystems,orwhenreplacingamplifiedsystem
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• PrewiredASWC-1harnessincluded(ASWC-1soldseparately)
• Highlevelspeakerinput
• USBupdatable
Note: TheXSVI-5524-NAVdoesnotretainSYNC.
APPLICATIONS
FORD
Edge(4.2”screen) 2011-up
Explorer(4.2”screen) 2011-up
F-150(4.2”screen) 2013-up
Fiesta 2011-up
(without MyFord Touch, with SYNC)
Focus 2012-up
(without MyFord Touch, with SYNC)
WIRING UP THE XSVI-5524-NAV
• ConnecttheYellowwiretotheradio’s12voltbatteryormemorywire.
• ConnecttheBlackwiretotheradio’sgroundwire.
• ConnecttheRedwiretotheignitionwireoftheaftermarketradio
• ConnecttheOrangewiretotheilluminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeofftheorangewire.
• Connectthe Blue wiretotheantennaturnonwireoftheaftermarketradio.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
XSVI-5524-NAV
XSVI-5524-NAV
Ford accessory and NAV output CAN harness 2011-up
• Providesaccessory(12volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinnon-amplifiedsystems,orwhenreplacingamplifiedsystem
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• PrewiredASWC-1harnessincluded(ASWC-1soldseparately)
• Highlevelspeakerinput
• USBupdatable
Note: TheXSVI-5524-NAVdoesnotretainSYNC.
APPLICATIONS
FORD
Edge(4.2”screen) 2011-up
Explorer(4.2”screen) 2011-up
F-150(4.2”screen) 2013-up
Fiesta 2011-up
(without MyFord Touch, with SYNC)
Focus 2012-up
(without MyFord Touch, with SYNC)
WIRING UP THE XSVI-5524-NAV
• ConnecttheYellowwiretotheradio’s12voltbatteryormemorywire.
• ConnecttheBlackwiretotheradio’sgroundwire.
• ConnecttheRedwiretotheignitionwireoftheaftermarketradio
• ConnecttheOrangewiretotheilluminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeofftheorangewire.
• Connectthe Blue wiretotheantennaturnonwireoftheaftermarketradio.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
Ford accessory and NAV output CAN harness 2011-up
• Providesaccessory(12volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinnon-amplifiedsystems,orwhenreplacingamplifiedsystem
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• PrewiredASWC-1harnessincluded(ASWC-1soldseparately)
• Highlevelspeakerinput
• USBupdatable
Note: TheXSVI-5524-NAVdoesnotretainSYNC.
APPLICATIONS
FORD
Edge(4.2”screen) 2011-up
Explorer(4.2”screen) 2011-up
F-150(4.2”screen) 2013-up
Fiesta 2011-up
(without MyFord Touch, with SYNC)
Focus 2012-up
(without MyFord Touch, with SYNC)
WIRING UP THE XSVI-5524-NAV
• ConnecttheYellowwiretotheradio’s12voltbatteryormemorywire.
• ConnecttheBlackwiretotheradio’sgroundwire.
• ConnecttheRedwiretotheignitionwireoftheaftermarketradio
• ConnecttheOrangewiretotheilluminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeofftheorangewire.
• Connectthe Blue wiretotheantennaturnonwireoftheaftermarketradio.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
XSVI-5524-NAV
Ford accessory and NAV output CAN harness 2011-up
• Providesaccessory(12volt10amp)
• RetainsR.A.P.(retainedaccessorypower)
• Usedinnon-amplifiedsystems,orwhenreplacingamplifiedsystem
• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)
• PrewiredASWC-1harnessincluded(ASWC-1soldseparately)
• Highlevelspeakerinput
• USBupdatable
Note: TheXSVI-5524-NAVdoesnotretainSYNC.
APPLICATIONS
FORD
Edge(4.2”screen) 2011-up
Explorer(4.2”screen) 2011-up
F-150(4.2”screen) 2013-up
Fiesta 2011-up
(without MyFord Touch, with SYNC)
Focus 2012-up
(without MyFord Touch, with SYNC)
WIRING UP THE XSVI-5524-NAV
• ConnecttheYellowwiretotheradio’s12voltbatteryormemorywire.
• ConnecttheBlackwiretotheradio’sgroundwire.
• ConnecttheRedwiretotheignitionwireoftheaftermarketradio
• ConnecttheOrangewiretotheilluminationwireoftheaftermarketradio.Ifthe
aftermarketradiohasnoilluminationwire,tapeofftheorangewire.
• Connectthe Blue wiretotheantennaturnonwireoftheaftermarketradio.
• ConnecttheWhitewiretotheleftfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheWhite/Blackwiretotheleftfrontnegativespeakeroutputofthe
aftermarketradio.
INSTXSVI-5524-NAV
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 4/29/14
INSTXSVI-5524-NAV
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 4/29/14
INSTXSVI-5524-NAV
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 4/29/14
INSTXSVI-5524-NAV
© COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
REV. 4/29/14
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• Connectthe Purplewiretotheradio’srightrearpositivespeakeroutput.
• Connectthe Purple/Blackwiretotheradio’srightrearnegativespeakeroutput.
Thefollowingwiresarefortheaftermarketradiosthathavenavigationbuiltin.
• Connectthe Light Greenwiretotheparkingbrakewireoftheaftermarketnavigation
radio(ifapplicable).
• ConnecttheBlue/PinkwiretotheVSSorspeedsensewireoftheaftermarket
navigationradio(ifapplicable).
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio
(ifapplicable).
• Cyclethekeybyturningtheignitiononfor30seconds,then“off”and“on”againto
testtheradio.
ASWC-1 (if installing)
AftertheXSVIisinitialized,plugintheASWC-1intothe12pinharnessofthe
XSVI-5524-NAVandrefertotheASWC-1instructions.
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Caution: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
Note: Refer to the instructions included with the
aftermarket radio.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• Connectthe Purplewiretotheradio’srightrearpositivespeakeroutput.
• Connectthe Purple/Blackwiretotheradio’srightrearnegativespeakeroutput.
Thefollowingwiresarefortheaftermarketradiosthathavenavigationbuiltin.
• Connectthe Light Greenwiretotheparkingbrakewireoftheaftermarketnavigation
radio(ifapplicable).
• ConnecttheBlue/PinkwiretotheVSSorspeedsensewireoftheaftermarket
navigationradio(ifapplicable).
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio
(ifapplicable).
• Cyclethekeybyturningtheignitiononfor30seconds,then“off”and“on”againto
testtheradio.
ASWC-1 (if installing)
AftertheXSVIisinitialized,plugintheASWC-1intothe12pinharnessofthe
XSVI-5524-NAVandrefertotheASWC-1instructions.
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• Connectthe Purplewiretotheradio’srightrearpositivespeakeroutput.
• Connectthe Purple/Blackwiretotheradio’srightrearnegativespeakeroutput.
Thefollowingwiresarefortheaftermarketradiosthathavenavigationbuiltin.
• Connectthe Light Greenwiretotheparkingbrakewireoftheaftermarketnavigation
radio(ifapplicable).
• ConnecttheBlue/PinkwiretotheVSSorspeedsensewireoftheaftermarket
navigationradio(ifapplicable).
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio
(ifapplicable).
• Cyclethekeybyturningtheignitiononfor30seconds,then“off”and“on”againto
testtheradio.
ASWC-1 (if installing)
AftertheXSVIisinitialized,plugintheASWC-1intothe12pinharnessofthe
XSVI-5524-NAVandrefertotheASWC-1instructions.
• ConnecttheGraywiretotherightfrontpositivespeakeroutputofthe
aftermarketradio.
• ConnecttheGray/Black wiretotherightfrontnegativespeakeroutputofthe
aftermarketradio.
• ConnecttheGreenwiretotheradio’sleftrearpositivespeakeroutput.
• ConnecttheGreen/Blackwiretotheradio’sleftrearnegativespeakeroutput.
• Connectthe Purplewiretotheradio’srightrearpositivespeakeroutput.
• Connectthe Purple/Blackwiretotheradio’srightrearnegativespeakeroutput.
Thefollowingwiresarefortheaftermarketradiosthathavenavigationbuiltin.
• Connectthe Light Greenwiretotheparkingbrakewireoftheaftermarketnavigation
radio(ifapplicable).
• ConnecttheBlue/PinkwiretotheVSSorspeedsensewireoftheaftermarket
navigationradio(ifapplicable).
• Connectthe Green/Purplewiretothereversewireoftheaftermarketnavigationradio
(ifapplicable).
• Cyclethekeybyturningtheignitiononfor30seconds,then“off”and“on”againto
testtheradio.
ASWC-1 (if installing)
AftertheXSVIisinitialized,plugintheASWC-1intothe12pinharnessofthe
XSVI-5524-NAVandrefertotheASWC-1instructions.
  • Page 1 1
  • Page 2 2

Metra Electronics XSVI-5524-NAV User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI