© Welbilt, Inc.© Welbilt, Inc.© Welbilt, Inc.
Crafted for Every Taste
© Welbilt, Inc.© Welbilt, Inc.
Installation of the
Unity connectivity
kit.
2
© Welbilt, Inc.© Welbilt, Inc.
3
Enabling Objectives
Upon successful completion of this training you will be able to:
- Identify all components associated with a connectivity kit.
- Properly connect all components of a connectivity kit.
- Properly load all software for the installation of the
connectivity kit.
© Welbilt, Inc.© Welbilt, Inc.
Tools
44
- Phillips Screwdriver (New Units)
- T10 Hex Screwdriver (Legacy Units)
- Needle Nose Pliers
- Flathead Screwdriver
- Micro Wire Cutters
© Welbilt, Inc.© Welbilt, Inc.
Inspection
55
1. Examine the kit for all of the components.
1 Transponder
1 Male ended coaxial
1 Lock washer
1 Nut
1 T-10 Bolt
1 IMEI Card
© Welbilt, Inc.© Welbilt, Inc.
66
Front Panel
2. Open the Front Panel.
Note:
Ensure that the unit is off prior to removing
the screen.
Use the key to unlock the panel and pull the
screen towards you.
© Welbilt, Inc.© Welbilt, Inc.
77
Remove the back plate
3. Remove the plate on the back of the Front Panel.
Note:
Removing the hoppers
will make it easier to
access the back plate.
Release the plastic cover locks on either
side of the plate and remove the plate
from the back of the front panel.
© Welbilt, Inc.© Welbilt, Inc.
88
Unfasten the screen
4. Remove the screws on the back of the screen.
Locate the screw
ports as shown in
the photo to the
right.
Using either the T-
10 Hex for Legacy
units or precision
Philips for new
units, unscrew the
screen from the
front panel.
The screws will not
come all the way
out of the machine.
(only unscrew them until the screen is not fastened to the front panel)
© Welbilt, Inc.© Welbilt, Inc.
99
Unfasten the screen
5. Unhook the screen from the front panel.
Being cautious of
the connections on
the back of the
screen unhook the
screen.
Disconnect the USB
on the top right of
the screen.
Unfasten the spring
bracket.
Pro Tip!
If you are mindful
of the connections
the screen can
gravity hang while
you are getting
tools and the
connectivity kit
ready.
© Welbilt, Inc.© Welbilt, Inc.
1010
Prepare the Kit
6. Place SIM card inside IMEI card.
Connect the coaxial
push tab to the
IMEIs top center
tab.
Insert SIM into
IMEI Card.
© Welbilt, Inc.© Welbilt, Inc.
1111
Install the Kit
7. Place Transmitter on the inside of the front casing.
© Welbilt, Inc.© Welbilt, Inc.
1212
Install the Kit
8. Remove shield plate.
Remove shield
plating on the
bottom left of the
board.
Pro Tip!
You can remove the plating using either
micro wire cutters or a small flat head
screwdriver to expose the plate and work
it off.
© Welbilt, Inc.© Welbilt, Inc.
1313
Install the Kit
9. Insert the male coaxial connection through the hole on the bottom left.
Using the lock washer and nut, fasten the coaxial to the plate as shown.
© Welbilt, Inc.© Welbilt, Inc.
1414
Install the Kit
10. Connect the IMEI card to the serial port on the bottom of the board.
Pro Tip!
Routing the excessive wire behind the IMEI card allows for better access
to the serial port as shown.
© Welbilt, Inc.© Welbilt, Inc.
1515
Install the Kit
11. Connect the male and female coaxial connections.
© Welbilt, Inc.© Welbilt, Inc.
1616
Install the Kit
12. Connect the USB port.
© Welbilt, Inc.© Welbilt, Inc.
1717
Install the Kit
13. Fasten the spring bracket.
© Welbilt, Inc.© Welbilt, Inc.
1818
Place the screen and front panel back plate back
14. Hook the screen back onto the top bracket.
© Welbilt, Inc.© Welbilt, Inc.
1919
Place the screen and front panel back plate back
15. Fasten the screen back screws.
© Welbilt, Inc.© Welbilt, Inc.
2020
Place the screen and front panel back plate back
16. Fasten the front panel back plate.
Note:
Replace the hoppers
after complete.
Align the plastic cover locks on either
side of the plate and fasten the plate on
the back of the front panel.
Page is loading ...
Page is loading ...
/
