TMI Products 1994-98 Mustang Coupe Upholstery Kit Installation guide

Brand
TMI Products
Model
1994-98 Mustang Coupe Upholstery Kit
Type
Installation guide
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Preparation
Page1of25
IssueA:12-01-11
Item2
Item3
Item5
Item4
Part#:43-76624,43-76724,43-76324,43-76627,43-76727,43-76327,43-76628,43-76728,
43-76328
Conflicts:Convertible-KitforCoupeModelsOnly
KitContents:
HardwareContent
Item# QuantityReqd. Description
1 2 BackrestUpholstery
2 2 SeatBottomUpholstery
3 2 HeadrestCovers
4 2 BackrestSeatFoam
5 2 SeatBottomSeatFoam
6 4 LSupportRods
7 6 111/2”MainRods
8 6 12”MainRods
9 4 15”SupportRods
10 1 RearUpperUpholstery
11 1 RearLowerUpholstery
12 4 13”MetalRods
13 6 137/8”MetalRods
14 6 PlasticStringAnchor
15 18FT String(Cutto18”Pieces)
AdditionalItems(mayberequired)
Item# QuantityReqd. Description
1 91 HogRings
2 2 ThinPlasticBag
3 1 ClothesHanger
RecommendedSequenceofApplication
Item# Accessory
Legend
STOP:Damagetothevehiclemayoccur.Donotproceeduntil
processhasbeencompliedwith.
CAUTION:Aprocessthatmustbecarefullyobservedinorderto
reducetheriskofdamagetotheaccessory/vehicle.
OPERATORSAFETY:Usecautiontoavoidriskofinjury.
TOOLS&EQUIPMENT:UsedinFigurestocalloutthespecific
toolsandequipmentrecommendedfortheprocess.
REVISIONMARK:Thismarkhighlightsachangeininstallation
withrespecttopreviousissue.
SAFETYTORQUE:Thismarkindicatesthattorqueisrelatedto
safety.
VIDEO:VideoAvailable;clicktoPlay
RecommendedTools
Personal&VehicleProtection Notes
SafetyGoggles
Latex/RubberGloves
SpecialTools
Sockets 10mm(DeepSocket),5/8”,1/2”
Screwdriver Phillips,Flathead
WireCutters
HogRingPliers
TorxScrewdriver T45,T25
HeyKey 2mm
ThreadingNeedle Canbemadeusingaclotheshanger
RazorBlade(S)
Steamer/HeatGun
SpecialChemicals Notes
FoamLock™Glue
Usedtosecurecovertofoam
Vinyl/LeatherCleaner Optional-Usedtocleancoverafterinstallation
Item1
Item6
Item8
Item7
TM
Item9
Item11
Item12
Item14
Item13
Item10
Item15
99-6624-000REV1
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Preparation
Page2of25
IssueA:12-01-11
TableofContents
I. Preparation............................................................................................................................................... 1-2
1. TableOfContents..................................................................................................................................2
II. Procedure...............................................................................................................................................3-15
1. FrontDriverandPassengerSeatDisassembly......................................................................................3
2. InstallTMIFoamandUpholsterytoSeatBottomFrame....................................................................7
3. InstallTMIFoamandUpholsterytoBackrestFrame.........................................................................10
4. RemoveandInstallHeadrestUpholstery...........................................................................................15
5. RearSeatRemoval................................................................................................................................16
6. RemoveFactorySeatUpholstery........................................................................................................16
7. TMIReplacementUpholsteryInstall-RearLowerCushion..............................................................18
8. TMIReplacementUpholsteryInstall-RearUpperCushion..............................................................24
AccessoryInstallationPractice(readbeforeinstallation)
Caremustbetakenwheninstallingthisaccessorytoensuredamagedoesnotoccurtothevehicleorvehicle’scomponents.Theinstal-
lationofthisaccessoryshouldfollowapprovedguidelinestoensureaqualityinstallation.
Thisdocumentcoverssuchitemsas:
• VehicleProtection(useofcoversandblankets,cleaningchemicals,etc.)
• Safety(eyeprotection,checkingtorqueprocedure,etc.)
• VehicleDisassembly/Reassembly(panelremoval,partstorage,etc.)
• ElectricalComponentDisassembly/Reassembly(batterydisconnection,connectorremoval,etc.)
PleaseseeyourAuthorizedTMIProductsdealerforacopyofthisdocument.
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page3of25
IssueA:12-01-11
1. FrontDriverandPassengerSeatDisassembly
a. Disconnect(-)Negativeterminalonbattery.
b. Removefrontdriverandpassengerseat.
1. UsingaPhillipsscrewdriver,removethe
plasticretaininglockslocatedontheplastic
trims.
2. Pullplastictrimsrearwardtoremove(Fig.
1).
3. Removetworearboltsandtwofrontbolts
usinga5/8”ratchet/socket(Fig.2andInsert
Image).
4. Disconnectanyconnectorsandremoveseat.
5. Repeatsteps1-4toremoveotherfrontseat.
c. Removereclinerlevercovers.
1. UsingaPhillipsscrewdriverremoveone
screwonthebacksideofthecoverandre-
move(Fig.3).
NOTE:Coversarelocatedonrightsideforpas-
sengerseatandonleftsidefordriverseat.
PhillipsScrewdriver
Fig.1
5/8”Ratchet/Socket
Fig.2
Fig.3
PhillipsScrewdriver
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page4of25
IssueA:12-01-11
d. Removebackrestreleaselever.
1. RemoverubberlevercapandonePhillips
screwtoremove(Fig.4).
e. Removeseatrails.
1. Usinga10mmratchet/socket,removefour
boltssecuringtheseatrailtotheseat(Fig.
5).
2. Removetensionspring(InsertImage).
f. Removebackrestfromseatbottom.
1. Removetwoboltsusinga1/2”ratchet/
socket(Fig.6).
NOTE:Locatedonrightsideonpassengerseat
andleftsideondriverseat.
2. RemoveoneboltusingaTroxT45(Insert
Image).
NOTE:Locatedonleftsideonpassengerseatand
rightsideondriverseat.
Fig.4
Fig.5
Fig.6
PhillipsScrewdriver
10mmRatchet/Socket
1/2”Ratchet/Socket,TorxT45
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page5of25
IssueA:12-01-11
3. Disconnectlumbarsupporthose(Fig.7).
g. Removelumbarsupportswitchbezel.
1. Pushinthesidesofthebezeltoremove
(Fig.8).
STEP2-3AREFORTHEDRIVERSIDESEAT
ONLY(Skipstep2-3forpassengerseat).
2. Removeseatbottomadjustmentknobusing
a2mmhexkey(TopInsertImage).
3. RemovepowerseatcontrolusingaPhillips
screwdriver(BottomInsertImage).
h. Removeseatbottomupholstery.
1. Usingaflatheadscrewdriverorappropri-
ateprytool,releasetheJ-Clipssecuringthe
upholsterytotheseatframe(Fig.9).
DriverSeatOnly
DriverSeatOnly
Fig.7
Fig.8
Fig.9
Phillipsscrewdriver/2mmHexKey
FlatheadScrewdriver
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page6of25
IssueA:12-01-11
2. Carefullyremovethefoamcushionand
upholsteryfromtheframe(Fig.10).
i. Removebackrestfoamandupholsteryfrom
seatframe.
1. DisconnectJ-Clipfrombottomofbackrest
(Fig.11).
2. Removeheadrestbyreleasinglocking
mechanismandpullingtheheadrestout
(Fig.12andTopInsertImage).
NOTE:Toaccessreleaselevertoheadrestand
postguide,werecommendcuttingtherearofthe
backrestupholsteryasshown.
3. Removepostguidebyreleasethelocktabs
onthesidesofthepostguide(BottomInsert
Image).
Fig.10
Fig.11
Fig.12
RazorBlade
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page7of25
IssueA:12-01-11
4. RemoveseatbeltholderusingaTroxT25
(Fig.13).
5. Carefullyremovethefactoryfoamandup-
holsteryfrombackrestframe(Fig.14).
2. InstallTMIFoamandUpholsterytoseatbot-
tomframe.
a. Placeseatbottomfoamontoframe(Fig.15).
Fig.13
Fig.14
Fig.15
TroxT25
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page8of25
IssueA:12-01-11
b. Insertlumbarsupporthosethroughseatbot-
tomfoam(Fig.16).
NOTE:Fig.16representsthepassengerseat.
Driverseatshouldbepositionontheopposite
side.
c. Secureupholsterytoseatbottomfoam.
1. Insertthethree12”mainrodsintotherod
sleeves(Fig.17).
2. Usinghogringsandhogringpliers,secure
mainrodstorodsupportsmoldedintothe
foamseatbottom(TopInsertImage).
NOTE:Locationofhogringtiedownsarehigh-
lightedintheBottomInsertImage.Usethreehog
ringsforeachsupportrod.
3. Insertthetwo15”supportrodsintotherod
sleeves(Fig.18).
4. Usinghogringsandhogringpliers,secure
mainrodstorodsupportsmoldedintothe
foamseatbottom.
NOTE:Locationofhogringtiedownsarehigh-
lightedintheInsertImage.Usefourhogringsfor
eachsupportrod.
3”
2”
Fig.16
Fig.17
Fig.18
HogRingPliers
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page9of25
IssueA:12-01-11
5. Makeaccessholeonupholsteryforlumbar
supporthose(Fig.19).
d. Secureupholsterytoseatframe.
1. Linethesideswiththinplasticbagstohelp
aligntheupholstery(Fig.20).
NOTE:Athintrashbagorgrocerybagcanbe
usedtolinethefoam.
Liningthefoamisnotrequired,however,itwill
makethefollowingstepseasier.
2. Foldupholsteryoverfoamcushionandalign
(Fig.21).
3. SecuretheJ-Clipstotheseatframe(Insert
Image).
Fig.19
Fig.20
Fig.21
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page10of25
IssueA:12-01-11
DriverSeatOnly
DriverSeatOnly
4. Useasteamerorheatguntogetmostofthe
wrinklesoutoftheupholstery(Fig.22).
5. Massageandadjusttheupholsterytoprop-
erlysetitontothefoamcushion(Insert
Image).
e. Reinstallseataccessories.
1. Pressinthesideoftheseattofeelforthe
locationsoftheseataccessories.
2. Usingarazorblade,carefullycutaccess
holesintheseatbottomtoreinstalltheseat
accessories(Fig.23)
3. Reinstallthelumbarsupport(rightsidefor
passenger,leftsidefordriver).
STEPS3-4AREFORTHEDRIVERSEAT
ONLY(Skipforpassengerseat).
4. Reinstallseatbottomadjustmentknob(In-
sertImages).
5. Pressinthefrontoftheseattofeelforthe
powerseatcontrollocation.
6. Usingarazorblade,carefullycutanaccess
holetoreinstallthepowerseatcontrol(Fig.
24).
Fig.22
Fig.23
Fig.24
Steamer/HeatGun
RazorBlade,2mmHexKey
RazorBlade,PhillipsScrewdriver
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page11of25
IssueA:12-01-11
f. Cutaccessholesforseatbrackets.
1. Pressinthesidesoftheseattofeelforthe
mountingbracketlocations.
2. Usingarazorblade,carefullycutaccess
holesusedtoreassembletheseatbottom
cushiontothebackrest(Fig.25).
NOTE:Pleasenotethatthedriverandpassenger
seatrequiredifferentholelocations.Refertostep
1.f.formoredetailsregardingholelocation.
3. InstallTMIFoamandUpholsterytobackrest
frame.
a. Slidebackrestfoamontoframe(Fig.26).
b. Securebackrestupholsteryontoseatfoam.
1. Linethetopandsidesofthebackrestfoam
withathinplasticbag(Fig.27).
NOTE:Athintrashbagorgrocerybagcanbe
usedtolinethefoam.
Liningthefoamisnotrequired,however,itwill
makethefollowingstepseasier.
2. Inverttheupholsteryabouthalfwayand
withalittleforce,pullthecoverdownonto
thefoam(InsertImage).
Fig.25
Fig.26
Fig.27
DriverSeat
PassengerSeat
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page12of25
IssueA:12-01-11
3. Insertthree111/2”mainrodsintotherod
sleeves(Fig.28).
4. Usinghogringandhogringpliers,secure
themainrodsleevestorodsupportsmolded
intothefoam.
NOTE:Hogtiedownlocationsarehighlightedin
theInsertImage.
5. Continueslidingtheupholsterydownonto
thebackrestfoam(Fig.29).
6. InserttwoLsupportrodsintotherodsleeve
(Fig.30).
NOTE:MakesuretheLsupportrodsgoes
throughtheloopslocatedontheendofthetop
rodsupport(InsertImage).
Fig.28
Fig.29
Fig.30
HogRingPliers
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page13of25
IssueA:12-01-11
7. SecureLsupportrodswithsixhogrings
(threeeachside)Fig.31).
8. Useasteamerorheatguntoremoveany
wrinklespresent(Fig.32).
9. ConnecttheJ-Clip.Massageandalignthe
upholsterytoproperlysetontothefoam
(Fig.33,InsertImage).
Fig.31
Fig.32
Fig.33
HogRingPliers
Steamer/HeatGun
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page14of25
IssueA:12-01-11
c. Reinstallbackrestsupportaccessory.
1. Pressinthetopoftheseattofeelforthe
headrestpostlocation.
2. Userazorbladetocutaccessholeforhead-
restpost(Fig.34).
NOTE:Holesizeshouldbeapproximately2
inches.
3. Insertheadrestpostguidewiththecavity
sidefacingthefrontoftheseat(Fig.35.).
4. Pressinthefrontoftheseattofeelforthe
seatbeltholderlocation.
5. Cutaccessholesfortheseatbeltholderand
secureusingthefactoryTroxscrews(Fig.
36).
Fig.34
Fig.35
Fig.36
RazorBlade
TroxScrewdriver
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page15of25
IssueA:12-01-11
6. Pressinthebackoftheseattofeelforthe
powerseatcontrollocation.
7. Cutaccessholesforthebackrestrelease
leverandsecureusingthefactoryPhillips
screws(Fig.37).
4. Installheadrestcovers.
a. Removefactoryheadrestcover.
1. UnhookfactoryJ-Clipandremovefactory
headrestcover(Fig.38).
b. InstallTMIheadrestcovers.
1. Lineheadrestwiththinplasticbag(Fig.39).
2. Pullheadrestcoveroverfoamandsecureby
interlockingtheJ-Clip(InsertImage).
3. Reinstallheadrests.
Fig.37
Fig.38
Fig.39
PhillipsScrewdriver
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page16of25
IssueA:12-01-11
WireCutters,RazorBlade
5. RearSeatRemoval
a. Removerearlowerseatcushion.
1. Pushingintheretainingclipsbetweenthe
lowercushionandthecarpetedcrossmem-
ber,thereisoneoneachside,thenliftto
removeseatcushion(Fig.40).
b. Removerearupperseatcushion(Fig.41).
1. Folddowntheuppercushionandremove
boltssecuringthetopoftheseatback.
2. Foldseatbackupandremovethelower
bolts/nutsandtheblackbraceonlatemodel
vehicles.
3. Nowremovetheseatbackassembly.
NOTE:It’seasiertoremovewiththeseatlocked
back.
10mmRatchet/Socket
Fig.40
Fig.41
Fig.42
6. RemovalofFactorySeatUpholstery
a. Removefactoryseatcoverfromrearlower
seatcushion.
1. Usingwirecutters,removeallfactoryhog
ringsonthebacksideoftherearlowerseat
cushion(Fig.42).
2. Usingarazorbladeoranyothercutting
tool,carefullycuttheseatcoverawayfrom
thefoam(Fig.InsertImage).
NOTE:Becarefulwhenperformingthisstepas
youdonotwanttoremovetoomuchfoamfrom
theseatcushion.
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page17of25
IssueA:12-01-11
3. Fig.43isarepresentationofwhatyou
shouldhaveleftover.
b. Removefactoryseatcoverfromrearupper
seatcushions.
1. RemoveupperplasticsupportwithaPhil-
lipsscrewdriver(Fig.44).
Fig.43
Fig.44
Fig.45
PhillipsScrewdriver
2. Lifttheseatcoveroffthefoam(Fig.45).
3. Usingarazorbladeoranyothercuttingtool,
carefullycuttheseatcoverawayfromthe
foam(InsertImage).
NOTE:Becarefulwhenperformingthisstepas
youdonotwanttoremovetoomuchfoamfrom
theseatcushion.
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page18of25
IssueA:12-01-11
4. Removerearuppercushionbacksupportas
shown(Fig.46).
7. TMIReplacementUpholsteryInstallation-
RearLowerCushion
InstallTMI’srearlowerseatupholsteryontothe
factoryfoamcushion(Fig.47).
Fig.46
Fig.47
Fig.48
a. Install13”supportrod.
1. Usingone13”metalsupportrod(supplied),
insertitintothecenterrightrodsleeveas
shown(Fig.48).
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page19of25
IssueA:12-01-11
MetalRod
ThreadingTool
ThreadingTool
2. Usingathreadingneedleorappropriate
tool,threadthesuppliedstring(cutto18”)
throughtherodsleeve(abovetherod)and
throughthefoamasshown(Fig.49).
NOTE:Makesurethestringloopsaroundtherod
asshown(InsertImage).
Threadingneedlecanbemadeusingametal
clotheshanger.
3. Threadtwoadditionalstringsthroughthe
rodsleeveandfoamasshown(Fig.50).
Fig.49
Fig.50
Fig.51
4. Tightlysecurethethreestringstothesup-
pliedplasticanchorsasshown(Fig.51).
NOTE:Thiswillsecuretheupholsteryintothe
foamchannel.
5. Adjustandfirmlytightenthestringsas
neededwhilecheckingthefitmentofthe
upholstery(InsertImage).
FORD MUSTANG-COUPE 1994-1998 FULLUPHOLSTERYKIT
Procedure
Page20of25
IssueA:12-01-11
2. Positionthethreesecondaryrodsunderthe
mainsupportrodinstalledin7.a(Fig.53).
NOTE:Makesurethesecondaryrodsextendap-
proximately1/4”pastthemainsupportrod.
b. Installsecondarymetalrods.
1. Usingthree137/8”metalrods(supplied),
insertthemintotherodsleevesasshown
(Fig.52).
Fig.52
Fig.53
Fig.54
c. Installmainsupportrod.
1. Insertanother13”mainsupportrodintothe
rodsleeveasshown(Fig.54).
NOTE:Makesurethethreesecondaryrodsin-
stalledinstep7.boverlapsthemainrodapproxi-
mately1/4”.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

TMI Products 1994-98 Mustang Coupe Upholstery Kit Installation guide

Brand
TMI Products
Model
1994-98 Mustang Coupe Upholstery Kit
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents