Advantech PCN-6351 Series Startup Manual

Brand: Advantech

Model: PCN-6351 Series

Category: Motherboards

Type: Startup Manual

PCN-6351 Series Startup Manual 1

PCN-6351 Series Half-size Pentium

CPU

Card with VGA/LCD/Fast Ethernet Interface

Startup Manual

PCN-6351 Series Half-size Pentium

CPU Card with VGA/LCD/Fast Ethernet

Specifications

Standard SBC Functions

• CPU: Intel Pentium

MMX CPU 75/233 MHz, AMD

K5, K6, up to K6-300 MHz; Cyrix M1 PR 166/200

GP, M2-300; IDT Winchip C6 up to 240 MHz

• BIOS: AWARD 2 Mbit Flash BIOS, supports Plug &

Play, APM 1.2, Ethernet boot ROM, boot from

CD-ROM, LS-120, and ZIP drive

• Chipset: SiS 5582 (PCN-6351), SiS 5598

(PCN-6351L)

• L2 cache: 512 KB PB SRAM

• System memory: One 128-pin DIMM RAM socket

supports SDRAM memory modules from 8 to 256

• PCI IDE interface: One Enhanced IDE interface,

supports 2 IDE devices. Supports PIO mode 3, 4

with bus mastering up to 14 MB/sec, Ultra DMA

mode up to 33 MB/sec

• Floppy disk drive interface: Supports up to two

floppy disk drives: 3.5" (720 KB or 1.44 MB) and/or

5.25" (360 KB or 1.2 MB)

• Parallel port: One parallel port, supports

SPP/EPP/ECP

• IR port: Supports up to 4 Mbps transmission rates

• Serial ports: One RS-232, one RS-232/422/485

• Watchdog timer: Can generate a system reset or

IRQ 11. Software enabled/disabled. Time interval is

from 1 to 62 seconds. Jumperless with run-time

setup

VGA Function

PCN-6351

• Controller: C&T69000/C&T69030, supports 36-bit

LCD and CRT displays

• Display memory: 2 MB SDRAM built-in (optional 4 MB

with C&T69030)

• Display resolution: Up to 1280 x 1024 @ 256

colors (16 million colors @ 4 MB)

PCN-6351L

• Controller: SiS 5598 built-in VGA supports CRT

displays

• Display memory: Share system up to 4 MB

• Display resolution: Up to 1280 x 1024 @ 256

colors (16 million colors @ 4 MB)

Packing List

Before installing your board, make sure that the

following materials have been received:

• 1 PCN-6351 Series all-in-one single board computer

• 1 startup manual

• 1 hard disk drive (IDE) interface cable (40-pin)

p/n: 1701440500

• 1 floppy disk drive interface cable (34-pin)

p/n: 1701340600

• 1 parallel port adapter (26-pin) and COM2 adapter

(9-pin) kit p/n: 1700260250 p/n: 1701140201

• 1 6-pin mini-DIN keyboard and PS/2 mouse adapter

p/n: 1700060201

• 1 ATX/AT power cable and converter

p/n: 1700000450 p/n: 1700040052

• 1 CD-ROM (or disks) for utility, drivers and manual

(in PDF format)

• 1 warranty certificate

If any of these items are missing or damaged, contact

your distributor or sales representative immediately.

Note 1: For detailed information on the

PCN-6351 Series, please refer to the

enclosed CD-ROM or disk (in PDF format).

Note 2: Acrobat Reader is required to view any PDF

file. Acrobat Reader can be downloaded at:

www.adobe.com/Prodindex/acrobat/

readstep.html

(Acrobat is a trademark of Adobe.)

For more information on this and other Advantech

products, please visit our website at:

http://www.advantech.com

http://www.advantech.com/epc

For technical support and service, please visit our

support website at:

http://support.advantech.com

This manual is for the PCN-6351 and PCA-6351L

Rev. A1.

Part No. 2006635120 1st Edition

Printed in Taiwan Oct. 1999

2 PCN-6351 Series Startup Manual

The board has a number of jumpers that allow you to

configure your system to suit your application.

The table below lists the function of each of the

board's jumpers and connectors:

Jumpers

SW1 (Pins 1-3) CPU frequency rate setting

SW1 (Pin 4) Cache RAM mode setting

SW1 (Pins 5-6) CPU frequency setting

SW2 (Pins 1-4) CPU voltage setting

SW2 (Pins 5-6) Rev.

JP2 LCD setting

JP3 RTC & watchdog timer

JP4 COM2 setting for RS-232/422/

485

Jumpers and Connectors

Connectors

Number Function

A1 Socket 7

BT1 Battery socket

SDRAM1 DIMM connector

JP1 Ext. line pin header

CN1 PS/2 keyboard connector

CN2 Int. keyboard

CN3 PC/104 connector

CN4 HDD connector

CN5 COM2 connector

CN6 COM1 connector

CN7 LPT1 connector

CN8 FDD connector

CN9 VGA connector

CN10 LVDS connector

CN11 LCD controller connector

CN12 FAN connector

CN13 Power connector

CN14 USB connector

CN15 IR connector

CN16 LCD 24-bit connector

CN17 LCD 36-bit connector

CN18 LAN connector

CN19 CompactFlash™ socket

Jumper Settings

SW1: CPU frequency rate setting

Frequency rate Pin1 Pin2 Pin3

1.5 OFF OFF OFF

2 ON OFF OFF

2.5 ON ON OFF

3 OFF ON OFF

3.5 OFF OFF OFF

4 ON OFF ON

4.5 ON ON ON

5 OFF ON ON

SW1: Select cache RAM mode

Cache RAM mode Pin 4

Normal OFF

Cyrix linear mode ON

Ethernet Controller Functions (PCN-6351 only)

• Controller: RTL8139A 10 Mbps / 100 Mbps

• I/O address switchless setting

• Connector type: RJ-45

• Boot ROM: Built-in system (optional)

Solid State Disk

• Supports CompactFlash™ disks

Mechanical and Environmental

• Max. power requirement: 5 A @ +5 V, and +12 V

@ 100 mA

• Operating temperature: 0 ~ 60° C (32 ~ 140° F)

• Size: 204 mm x 122 mm (8.03" x 4.8")

PCN-6351 Series Startup Manual 3

SW2: Reserved

Function Pin 5 Pin 6

Rev. OFF OFF

Connectors pin assignments

JP1: Ext. line PIN header

Function Pin Pin Function

NC 1 2NC

GND 3 4NC

GND 5 6 ATX Power on/off

GND 7 8 RESET

HDD LED- 9 10 HDD LED +

Pwr LED + 11 12 NC

NC 13 14 Speaker +

GND 15 16 NC

KeyLock 17 18 Buzzer -

GND 19 20 Speaker -

Please note:

1. If using Buzzer, Pin18 and Pin20 need to be

shorted.

2. Speaker and Buzzer cannot be used together.

3. Wake on LAN has to be set to "Active Low" in order

to work properly.

4. The PCA-6016NP3 and PCA-6104NP2 backplanes'

PCI Slot 1 is set as "Passive PCI". If "Active PCI" is

required in your application, please use other PCI

slots.

5. To make the "Power Up by Alarm" function work, wait

until the FDD's POST procedure has been

completed. Then turn off the system.

6. In order to protect the CPU board, it is advisable to

wait 10 seconds before turning the system power

back on after a system shutdown.

7. Having an anti-EMI core as close to the printer

signal output (CPU board side) as possible is

recommended. This will minimize EMI affecting the

printer port.

JP2: LCD setting

JP4: COM2 select RS232/422/485

1112

JP3: Watchdog

setting reset

JP3: RTC setting

* default setting

SW2: Voltage setting

Voltage Pin 1 Pin 2 Pin 3 Pin 4

2 OFF OFF OFF OFF

2.1 ON OFF OFF OFF

2.2 OFF ON OFF OFF

2.3 ON ON OFF OFF

2.4 OFF OFF ON OFF

2.5 ON OFF ON OFF

2.6 OFF ON ON OFF

2.7 ON ON ON OFF

2.8 OFF OFF OFF ON

2.9 ON OFF OFF ON

3 OFF ON OFF ON

3.1 ON ON OFF ON

3.2 OFF OFF ON ON

3.3 ON OFF ON ON

3.4 OFF ON ON ON

3.5 ON ON ON ON

JP3: RTC & Watchdog setting

Function Pin Pin Function

NC 1 * 2 RESET

NC 3 4 WATCH_DOG

NC 5 6 IRQ11

NC 7 * 8 RTCVDD

NC 9 10 RTCVDD_IN

NC 11 12 RTC CLEAN

* default setting

JP2: LCD setting

Function Pin Pin Function

NC 1 2 NC

NC 3 4 NC

SHFCLK+ * 5 6 SCLK

SHFCLK- 7 8 SCLK

ENABKL+ * 9 10 ENBKL

ENABKL- 11 12 ENBKL

* default setting

RS-232 RS-422 RS-485

622

4 PCN-6351 Series Startup Manual

Mechanical Drawings

Board Dimensions

Locating Jumpers

PCN-6351 Series Startup Manual 5

Locating Connectors (Component Side)

Locating Connectors (Solder Side)

Mechanical Drawings

Advantech PCN-6351 Series Startup Manual

Brand: Advantech

Model: PCN-6351 Series

Category: Motherboards

Type: Startup Manual

Download PDF

report

Advantech PCN-6351 Series Startup Manual

Advantech PCN-6351 Series Startup Manual

Related papers

Other documents