Duplo DBM-120 Installation guide

Type
Installation guide
Provided By
http://www.MyBinding.com
http://www.MyBindingBlog.com
Duplo DBM-120
DC-6000S / 8000S 2 /
10000S Connecting
Kit
Installation Manual
Specialized person only
INSTALLATION MANUAL
DBM-120
CONNECTING KIT
(MODEL: DC-6000S/8000S 2/10000S)
Do not leave this Installation Manual at the installation site after installation.
Furthermore, do not leave tools used for the installation, at the installation site.
Retain this Installation Manual for future reference as it will be needed for subsequent
maintenance such as relocation.
TO SERVICING PERSONNEL
TABLE OF CONTENTS
1. Standard Accessories .....................................1
2. Installing Procedure ........................................2
2-1. Releasing the DBM-120 Lock..................2
2-2. Checking the DBM-120 EPROM .............2
2-3. Setting the DBM-120 ...............................4
2-4. Checking the Suction Collator EPROM ...6
2-5. Setting the DIP Switch of Suction
Collator ....................................................7
2-6. Connecting the Suction Collator ..............7
2-7. Connecting the Communication Cable ....9
1
The following parts are enclosed in the connecting kit. Check that you have all of them before
beginning installation.
1. STANDARD ACCESSORIES
No.
q
w
e
Qty. NameNo. Qty.
r
t
y
Cable clamp 2
Screw (MSKW4 × 8) 2
Installation manual 1
Communication cable 1
Connecting plate 1
Screw (MSKW5 × 10) 4
DBM-120
CONNECTING KIT
(MODEL: DC-6000S/8000S 2/10000S)
INSTALLATION MANUAL
Specialized person only
Name
q
w
er
ty
2
2. INSTALLING PROCEDURE
2-1. Releasing the DBM-120 Lock
Release the locks securing the bottom
plate of the DBM-120 and movable unit
together (2 each at the front and back).
Loosen the two screws of the fixing plate, and move
the fixing plate down and secure it.
NOTE : Be sure to complete above work before
turning on the power, or the unit may
damage.
1
Fixing plate
Movable unit
DBM-120
2-2. Checking the DBM-120 EPROM
Enter the maintenance menu.
q Press the (Escape) button once at the initial screen of the display on the control panel.
1
w Turn the jog dial by three clicks towards the right to
display “Number of Sheets” in the display.
Number of Sheets
2
e Press the (Clear) button once. A beep will be sounded.
Start button
Stop button
button
Clear
button
Escape
Jog dial/Enter button
Power ON indicator
Lights up when the
DBM-120 is turned ON.
Display
button
Function
3
2. INSTALLING PROCEDURE
r Turn the jog dial by 5 clicks towards the left to
display “Fine Adjustment” in the display.
Fine Adjustment
A3
t Press the button once. Two beeps will be
sounded, and “Maintenance Menu” will be displayed
in the display.
Maintenance Menu
Display the ROM version.
2
q Press the center of the jog dial.
w Press the center of the jog dial again.
The illustration on the right shows the display for
the ROM version “11C-80033”.
Select M. Mode
ROM Version
MC ROM Version
11C8OO33
Check the EPROM version displayed in the display.
If the version of the EPROM of the DBM-120 is 11C-80033 or more, it need not be replaced. If the version is 11C-80032
or less, replace the EPROM.
NOTE : Be sure to replace the EPROM if the version is 11C-80032 or less, or the DBM-120 will not operate.
The EPROM is a service parts.
3
To return to the initial screen
Press the button three times.
4
2. INSTALLING PROCEDURE
2-3. Setting the DBM-120
Enter the maintenance menu.
q Press the (Escape) button once at the initial screen of the display on the control panel.
1
w Turn the jog dial by three clicks towards the right to
display “Number of Sheets” in the display.
Number of Sheets
2
e Press the (Clear) button once. A beep will be sounded.
r Turn the jog dial by 5 clicks towards the left to
display “Fine Adjustment” in the display.
Fine Adjustment
A3
t Press the button once. Two beeps will be
sounded, and “Maintenance Menu” will be displayed
in the display.
Maintenance Menu
5
2. INSTALLING PROCEDURE
Select “Suction” at the “Select Collator” screen.
2
NOTE : If the collator set at the control panel of the DBM-120 and the collator actually connected differ, the
DBM-120 will not operate normally.
Select M. Mode
ROM Version
Collator
DC-1O
The selected collator shifts to
the beginning of the line and
starts blinking.
The collator displayed in the second
line is currently selected.
Select Collator
DC-1O DC-6/8 Su
Select Collator
Suction
Collator
Suction
q Press the center of the jog dial.
w Turn the jog dial to display “Collator” in the display.
e Press the center of the jog dial.
r Turn the jog dial to select “Suction”.
t Press the center of the jog dial to confirm the collator
to be connected.
To return to the initial screen
Press twice the button.
6
2. INSTALLING PROCEDURE
2-4. Checking the Suction Collator EPROM
Check the version of the EPROM in the ROM number check mode of the suction collator.
(1) Press the numerical keys on the control panel in the following order. 1 2 3 4 5 6
(2) Press the STOP key. The ROM number will be displayed on the display window as follows.
For the DC-10000S
“A-?” Display the ROM number of Tower A.
Press the STOP key.
“b-?” Display the ROM number of Tower B.
Press the STOP key.
“C-?” Display the ROM number of Tower C.
Press the STOP key.
“d-?” Display the ROM number of Tower D.
Press the STOP key.
“E-?” Display the ROM number of Tower E.
Press the STOP key.
“F-?” Display the ROM number of Tower F.
Release the check mode using the STOP key.
For DC-6000S, up to “C-?” will be displayed. For DC-8000S 2, up to “d-?” will be displayed.
DC-6000S If the version is 99L-80212 or more, it need not be replaced.
DC-8000S 2 If the version is 96F-82498 or more, it need not be replaced.
DC-10000S If the version is 96F-81999 or more, it need not be replaced.
NOTE : The DBM-120 will not operate normally with EPROMs of versions below the versions indicated above.
Use the same EPROM versions for all towers connected.
The EPROM is a service parts.
1
7
stop
start
2. INSTALLING PROCEDURE
2-5. Setting the DIP Switch of Suction Collator
Push down Pin 6 of DIP switch 2 on the control panel of Tower A of suction collator (to the
number side).
1
DIP switch 2
OPEN
12345678
DIP switch 2
DIP switch 1
DIP switch 4
DIP switch 3
This shows the DC-10000S.
2-6. Connecting the Suction Collator
Temporarily secure the connecting plate
provided to the DBM-120 cabinet.
<< Parts to be used >>
Connecting plate w ............................................ 1
Screw (MSKW5 × 10) e ................................... 2
1
DBM-120
DBM-120 cabinet
Connecting plate
Screws
Connecting plate
Screws
LU-HM
Temporarily secure the connecting plate
to the LU-HM.
<< Parts to be used >>
Screw (MSKW5 × 10) e ................................... 2
2
NOTE : Be sure to turn off the power of the DBM-120 and suction collator and disconnect the power plug from the
outlet first before starting the work.
Tighten the screws temporarily secured in step 1, and secure the connecting plate.
3
8
2. INSTALLING PROCEDURE
Check that the distance between the
paper in-feed slot of the DBM-120 and the
LU-HM exit is 8 to 12 mm (0.31" to 0.47").
NOTE : As the above range will not be satisfied if
the ground is not flat, check that the
ground is flat.
4
DBM-120
Guide
8 to 12 mm
(0.31" to 0.47")
LU-HM
Paper ejection rollers
DBM-120
Guide
3 to 7 mm
(0.12" to 0.28")
LU-HM
Paper ejection rollers
Adjust the height of the LU-HM exit so that
the paper in-feed slot of the DBM-120 is 3
to 7 mm (0.12" to 0.28") lower than the
LU-HM exit.
5
q Loosen the top two screws of the pillars of both the
operating and non-operating sides.
Pillar
Screws
Fixing nut
Bolt
Up
Down
w Loosen the nut fixing the bolt inside the pillar, and
turn the bolt to adjust the height of the LU-HM exit.
NOTE : Adjust so that the operating and non-
operating sides of the LU-HM exit
become the same height.
e After adjusting, tighten the nut, secure the bolt, and
tighten the top screws of the pillar.
9
A3
2. INSTALLING PROCEDURE
Turn on the power supply of the DBM-120, and set to the A3 size.
Refer to “6-1. Basic Operation” in the instruction manual of the DBM-120 for details on
setting the paper size.
6
Adjust the A3 mark on the
indication label to this face
LU-HM exit
jam sensor
Indication label of DBM-120
2-7. Connecting the Communication Cable
Connect the communication cable
provided to the connector of the DBM-120.
After connecting, be sure to tighten the
screws.
<< Parts to be used >>
Communication cable q .................................... 1
1
Connect the other connector of the
communication cable to the connector (at
the bottom) for connecting the peripheral
devices of the suction collator.
After connecting, be sure to tighten the
screws.
2
Communication cable
Suction collator
Screws
DBM-120
Communication cable
Screws
Adjust at the long holes of the connecting plate so that the A3 mark on the indication label of
the DBM-120 faces the LU-HM exit jam sensor side facing up, and tighten the screws
temporarily secured in step 2 to secure the connecting plate and LU-HM.
7
10
This ends the installation procedure.
2. INSTALLING PROCEDURE
Fix the communication cable to connecting
plate of LU-HM.
<< Parts to be used >>
Cable clamp r ................................................... 2
Screw (MSKW4 × 8) t ..................................... 2
3
Cable clamps
Connecting plate
Suction collator
NOTE : Move the DBM-120 unit to and fro when changing the paper size. Move aside the power cord so that it does
not touch the DBM-120 at this time.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Duplo DBM-120 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI