H3C MSR830-10EI-GL Installation guide

Brand: H3C

Model: MSR830-10EI-GL

Type: Installation guide

This manual is also suitable for

H3C MSR830 Router Series

Installation Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com

Document version: 6W100-20180818

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H

Care, , IRF, NetPilot, Netflow, SecEngine,

SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies

Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. All contents in this document, including

statements, information, and recommendations, are believed to be accurate, but they are presented without

warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions

contained herein.

Environmental protection

This product has been designed to comply with the environmental protection requirements. The storage, use,

and disposal of this product must meet the applicable national laws and regulations.

Preface

The H3C MSR830 Router Series Installation Guide includes seven chapters, which describe the

preparing for installation, installing the router, replacement procedure, troubleshooting, chassis

views and technical specifications, LEDs, and slot arrangement.

This preface includes the following topics about the documentation:

• Audience.

• Conventions.

• Documentation feedback.

Audience

This documentation is intended for:

• Network planners.

• Field technical support and servicing engineers.

• Network administrators working with the MSR830 Router Series.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Description

Boldface Bold

text represents commands and keywords that you enter literally as shown.

Italic

Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars,

from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n>

The argument or keyword and argument combination before the ampersand (&) sign

can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface

Window names, button names, field names, and menu items are in Boldface. For

example, the

New User

window opens; click

Convention Description

Multi-level menus are separated by angle brackets. For example,

File

Create

Folder

Symbols

Convention Description

WARNING!

An alert that calls attention to important information that if not understood or followed

can result in personal injury.

CAUTION:

An alert that calls attention to important information that if not understood or followed

can result in data loss, data corruption, or damage to hardware or software.

IMPORTANT:

An alert that calls attention to essential information.

NOTE:

An alert that contains additional or supplementary information.

TIP:

An alert that provides helpful information.

Network topology icons

Convention Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that

supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access

controller engine on a unified wired-WLAN switch.

Represents an access point.

Represents a wireless terminator unit.

Represents a wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security

gateway, or load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL

VPN, IPS, or ACG module.



Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots,

and other information in the examples differ from what you have on your device.

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

Contents

Preparing for installation ···································································· 1

Safety recommendations ············································································································· 1

Safety symbols ··················································································································· 1

General safety recommendations ··························································································· 1

Electricity safety ·················································································································· 1

Examining the installation site ······································································································· 1

Temperature and humidity ····································································································· 2

Cleanliness ························································································································ 2

Cooling system ··················································································································· 2

ESD prevention ··················································································································· 3

EMI ·································································································································· 3

Lightning protection ············································································································· 3

Rack-mounting ··················································································································· 4

Installation tools ························································································································· 4

Installation accessories ··············································································································· 4

Pre-installation checklist ·············································································································· 5

Installing the router ··········································································· 6

Installation prerequisites ·············································································································· 6

Installation flow ·························································································································· 6

Installing the router ····················································································································· 8

Mounting the router on a workbench ························································································ 8

Installing the router in a rack ·································································································· 8

Grounding the router················································································································· 10

Attaching the ring terminal to the grounding cable ···································································· 10

Grounding the router with a grounding strip ············································································· 11

Grounding the router through the rack···················································································· 11

Installing a Micro SD card ·········································································································· 12

Connecting a USB drive ············································································································ 13

Connecting interface cables ······································································································· 13

Connecting an AC power cord ······························································································ 13

Connecting an Ethernet cable ······························································································ 14

Connecting an optical fiber ·································································································· 15

Connecting the console cable and setting terminal parameters ·························································· 16

Connecting the console cable ······························································································ 16

Setting terminal parameters ································································································· 16

Verifying the installation ············································································································· 17

Accessing the router for the first time ··························································································· 17

Replacement procedure ·································································· 19

Replacing a Micro SD card ········································································································· 19

Replacing a transceiver module ·································································································· 20

Troubleshooting ············································································· 21

Power supply system failure ······································································································· 21

Configuration terminal issues ······································································································ 21

No terminal display ············································································································ 21

Garbled terminal display ····································································································· 22

No response from the serial port ··························································································· 22

Restoring the factory settings ····································································································· 22

Scenario 1 ······················································································································· 22

Scenario 2 ······················································································································· 22

Scenario 3 ······················································································································· 23

Reset button usage guidelines ····························································································· 23

Appendix A Chassis views and technical specifications ·························· 24

Chassis views ························································································································· 24

MSR830-6EI-GL ··············································································································· 24

MSR830-6HI-GL ··············································································································· 24

MSR830-10HI-GL ·············································································································· 25

MSR830-10EI-GL ·············································································································· 25

Technical specifications ············································································································· 26

Appendix B LEDs ··········································································· 27

Panel LEDs ···························································································································· 27

MSR830-6EI-GL ··············································································································· 27

MSR830-6HI-GL ··············································································································· 27

MSR830-10HI-GL ·············································································································· 28

MSR830-10EI-GL ·············································································································· 28

LED description ······················································································································· 28

Index ··························································································· 30

Preparing for installation

Figure 1 This document applies to the following device models:

Model Product code

MSR830-6EI-GL RT-MSR830-6EI-GL

MSR830-6HI-GL RT-MSR830-6HI-GL

MSR830-10HI-GL RT-MSR830-10HI-GL

MSR830-10EI-GL RT-MSR830-10EI-GL

Safety recommendations

Safety symbols

When reading this document, note the following symbols:

WARNING means an alert that calls attention to important information that if not understood or

followed can result in personal injury.

CAUTION means an alert that calls attention to important information that if not understood or

followed can result in data loss, data corruption, or damage to hardware or software.

General safety recommendations

• Keep the chassis and installation tools away from walk areas.

• Make sure the ground is dry and flat and anti-slip measures are in place.

• Unplug all the external cables (including power cords) before moving the chassis.

Electricity safety

• Locate the emergency power-off switch in the room before installation. Shut the power off at

once in case accident occurs. Disconnect the power cord of the router if necessary.

• Make sure the router is correctly grounded.

• Do not open or close the chassis cover when the router is powered on.

• Correctly connect the interface cables of the router.

• Use an uninterrupted power supply (UPS).

• Do not work alone when the router has power.

• Always make sure the power has been disconnected during the installation and replacement

procedures.

Examining the installation site

The router can only be used indoors. To make sure the router operates correctly and to prolong its

service lifetime, the installation site must meet the following requirements.

Temperature and humidity

Maintain temperature and humidity in the equipment room at acceptable levels.

• Lasting high relative humidity tends to cause poor insulation, electricity leakage, mechanical

property change of materials, and corrosion of metal parts.

• Lasting low relative humidity is likely to result in loose screws due to washer contraction, and

even ESD, which causes the circuits to fail.

• A high temperature is the most undesirable condition, because it accelerates the aging of

insulation materials and significantly lowers reliability and service life of the router.

For the temperature and humidity requirements of the router, see Table 1.

Table 1

Temperature and humidity requirements

Temperature Humidity

0°C to 45°C (32°F to 113°F) 5% to 90% (noncondensing)

Cleanliness

Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of

metal components and contact points, especially when indoor relative humidity is low. In the worst

case, electrostatic adsorption can cause communication failure.

Table 2 Dust concentration limit in the equipment room

Substance Concentration limit (particles/m

)

Dust particles

≤ 3 x 10

(No visible dust on desk in three days)

NOTE:

Dust particle diameter ≥ 5 µm

The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and

premature aging of components, as shown in Table 3.

Table 3

Harmful gas limits in the equipment room

Gas Max. (mg/m

)

0.2

S 0.006

0.05

0.01

0.04

0.01

Cooling system

To ensure good ventilation, the following requirements must be met:

• The air inlet and outlet vents are not blocked, and leave at least 100 mm (3.94 in) of clearance.

• The installation site has a good cooling system.

ESD prevention

CAUTION:

Check the resistance of the ESD wrist strap for safety. The resistance reading must be in the range

of 1 to 10 megohm (Mohm) between human body and the ground.

To prevent electrostatic discharge (ESD), follow these guidelines:

• Make sure the router and the floor are correctly grounded.

• Take dust-proof measures for the equipment room.

• Maintain the humidity and temperature at acceptable levels.

• Always wear an ESD wrist strap and ESD clothing when touching a circuit board or transceiver

module.

The router does not supply an ESD wrist strap. Prepare an ESD wrist strap yourself.

To attach an ESD wrist strap:

1. Wear the wrist strap on your wrist.

2. Lock the wrist strap tight around your wrist to keep good contact with the skin.

3. Secure the wrist strap lock and the alligator clip lock together.

4. Attach the alligator clip to the rack grounding terminal.

5. Make sure the rack is correctly grounded.

EMI

Electromagnetic interference (EMI) might be coupled from the source to the router through the

following coupling mechanisms:

• Capacitive coupling

• Inductive coupling

• Radiative coupling

• Common impedance coupling

• Conductive coupling

To prevent EMI, take the following actions:

• Take measures against interference from the power grid.

• Do not use the router together with the grounding equipment or lightning-prevention equipment

of power equipment, and keep the router far away from them.

• Keep the router far away from high-power radio launchers, radars, and equipment with high

frequency or high current.

• Use electromagnetic shielding when necessary.

Lightning protection

To better protect the router from lightning, do as follows:

• Make sure the grounding cable of the chassis is correctly grounded.

• Make sure the grounding terminal of the AC power receptacle is correctly grounded.

• Install a lightning arrester at the input end of the power supply to enhance the lightning

protection capability of the power supply.

Rack-mounting

Before mounting the router in a standard 19-inch rack, adhere to the following requirements:

• The rack is equipped with a good ventilation system.

• The rack is sturdy enough to support the router and its accessories.

• For heat dissipation and device maintenance, make sure the front and rear of the rack are at

least 0.8 m (2.62 ft) away from walls or other devices, and the headroom in the equipment room

is no less than 3 m (9.84 ft).

Installation tools

Installation accessories

Cage nut (user-supplied) M6 rack screw

Mounting brackets

M3 mounting bracket screw

Rubber feet

Bail latch

Ring terminal

Pre-installation checklist

Table 4 Pre-installation checklist

Item Requirements Result

Installation site

Ventilation

• There is a minimum clearance of 100 mm (3.94 in)

around the inlet and outlet vents for heat

dissipation of the router chassis.

• A good ventilation system is available at the

installation site.

Temperature 0°C to 45°C (32°F to 113°F).

Humidity 5% RH to 90% RH (noncondensing).

Cleanliness

• Dust concentration ≤ 3 × 104 particles/m3.

• No visible dust on desk within three days.

ESD prevention

• The equipment and floor are correctly grounded.

• The equipment room is dust-proof.

• The humidity and temperature are at acceptable

levels, respectively.

• Wear an ESD wrist strap and uniform when

touching a circuit board.

EMI prevention

• Take effective measures to protect the power

system from the power grid system.

• Separate the protection ground of the router from

the grounding device or lightning protection

grounding device as far as possible.

• Keep the router far away from radio stations, radar

and high-frequency devices working in high

current.

• Use electromagnetic shielding when necessary.

Lightning

protection

• The grounding cable of the chassis is correctly

grounded.

• The grounding terminal of the AC power

receptacle is correctly grounded.

• A port lightning arrester is installed. (Optional.)

• A power lightning arrester is installed. (Optional.)

• A signal lightning arrester is installed at the input

end of an external signal cable. (Optional.)

Electricity safety

• Equip an UPS.

• The power-off switch in the equipment room is

identified and accessible so that the power can be

immediately shut off when an accident occurs.

Workbench

• The workbench is stable enough.

• The workbench is correctly grounded.

Safety

precautions

• The router is far away from any moist area and heat source.

• The emergency power switch in the equipment room is located.

Tools

• Installation accessories supplied with the router.

• User supplied tools.

Reference

• Documents shipped with the router.

• Online documents.

Installing the router

WARNING!

To avoid injury, do not touch bare wires, terminals, or parts with high-voltage hazard signs.

IMPORTANT:

• The barcode on the router chassis contains product information that must be provided to local

sales agent when you return a faulty router for service.

• Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to

open the chassis, contact H3C for permission. Otherwise, H3C shall not be liable for any

consequence.

Installation prerequisites

• You have read "Preparing for installation" carefully.

• All requirements in "Preparing for installation" are me

Installation flow

You can install the router on a workbench or in a rack. Select an installation method according to the

installation environment, and follow the installation flowchart shown in Figure 2.

Figure 2 Installation flow

Yes

Start

Ground the router

Connect interface cables

Connect the router to a

configuration terminal

Connect the power cord

Verify the installation

Power on the router Troubleshoot the router

Power off the routerOperating correctly?

End

Mount the router on a

workbench

Mount the router in a rack

Determine the

installation position

Workbench-mounting

Rack-mounting

Install a Micro SD card

Install a USB drive

Installing the router

Mounting the router on a workbench

IMPORTANT:

• Ensure good ventilation and 100 mm (3.94 in) of clearance around the chassis for heat

dissipation.

• Do not place heavy objects on the router.

To mount the router on a workbench:

1. Make sure the workbench is clean, stable, and correctly grounded.

2. Place the router upside down on the workbench and attach the rubber feet to the four round

holes in the chassis bottom.

Figure 3 Attaching the rubber feet

3. Place the router on the workbench with the upside up.

Figure 4 Mounting the router on a workbench

Installing the router in a rack

WARNING!

The mounting brackets can only support the weight of the router. To avoid damage to the router, do

not place any objects on the router.

To install the router in a rack:

1. Use a mounting bracket to mark the positions of cage nuts on the front rack posts. Make sure

the cage nut installation holes on the front rack posts are on a horizontal line.

2. Install cage nuts, as shown in Figure 5.

a. Insert o

ne ear of a cage nut into the marked installation hole.

b. Use a flathead screwdriver to push the other ear into the same hole.

Figure 5 Installing cage nuts

3. Attach mounting brackets to both sides of the router, as shown in Figure 6.

Figure 6 Attaching the mounting bracket to the router

4. Use M6 screws to attach the mounting brackets on the router to the front rack posts, as shown

in Figure 7.

Figure 7 Securing the router to the rack

Grounding the router

WARNING!

Correctly connecting the router grounding cable is crucial to lightning protection and EMI protection.

IMPORTANT:

The resistance reading must be smaller than 5 ohms between the chassis and the ground.

Attaching the ring terminal to the grounding cable

The router comes with a ring terminal. No grounding cable is provided with the router. Purchase a

grounding cable yourself. Before grounding the router, attach the provided ring terminal to the

grounding cable.

To attach the ring terminal to the grounding cable:

1. Cut the grounding cable to the desired length. Use the wire-stripping pliers to peel 5 mm (0.20 in)

of insulation sheath from one end of the grounding cable.

2. Add a heat-shrink tubing onto the cable, and insert the bare metal part of the grounding cable

into the ring terminal.

3. Use the needle-nose pliers to secure the metal part of the cable in the ring terminal.

4. Cover the joint with the heat-shrink tubing, and use a heat gun to shrink the tubing around the

cable.

Figure 8 Attaching the ring terminal to the grounding cable

Grounding the router with a grounding strip

1. Remove the grounding screw from the grounding hole on the rear panel of the chassis.

2. Use the grounding screw to attach the ring terminal of the grounding cable to the grounding

hole.

3. Use a screwdriver to fasten the grounding screw.

4. Remove the hex nut from a grounding post on the grounding strip.

5. Use the removed hex nut to attach the other end of the grounding cable to the grounding post.

Figure 9 Connecting the router with a grounding strip

Grounding the router through the rack

IMPORTANT:

Make sure the rack is correctly grounded before grounding the router through the rack.

To connect the grounding cable through the rack:

1. Remove the grounding screw from the grounding hole on the rear panel of the chassis.

2. Use the grounding screw to attach the ring terminal of the grounding cable to the grounding

hole.

3. Use a screwdriver to fasten the grounding screw.

4. Remove the nut from the grounding post of the grounding point on the rack.

5. Use the needle-nose pliers to bend a hook at the other end of the grounding cable, and use the

removed nut to attach the hook to the grounding post.

Figure 10 Grounding the router through the rack

Installing a Micro SD card

CAUTION:

To avoid damaging the Micro SD card slot, do not use excessive force when you install a Micro SD

card.

Only the MSR830-6HI-GL and MSR830-10HI-GL routers support Micro SD cards.

To install a Micro SD card:

1. Remove the screw on cover over the Micro SD card slot and remove the cover.

2. Insert the Micro SD card into the slot along the slide rails.

If you encounter any resistance, re-orient the card and try to insert it again.

3. Reinstall the cover and fasten the screw on the cover.

Figure 11 Installing a Micro SD card

Connecting a USB drive

Connect a USB drive to the USB port of the router as shown in Figure 12.

Figure 12 Connecting a USB drive

Connecting interface cables

Connecting an AC power cord

1. Make sure the router is correctly grounded.

2. Attach the bail latch to the router.

3. Connect one end of the AC power cord to the AC receptacle on the router, and the other end to

the AC power source.

4. Use the bail latch to secure the power cord.

Page is loading ...

H3C MSR830-10EI-GL Installation guide

Brand: H3C

Model: MSR830-10EI-GL

Type: Installation guide

This manual is also suitable for

Download PDF

report

H3C MSR830-10EI-GL Installation guide

This manual is also suitable for

H3C MSR830-10EI-GL Installation guide

Related papers

Other documents