Armor Door VSDFDEX3680EL Installation guide

Brand
Armor Door
Model
VSDFDEX3680EL
Type
Installation guide
ADJUSTABLE FRAME - DRYWALL INSTALLATION INSTRUCTIONS
A
RMOR DOO
R
TM
DRYWALL INSTALLATION
ROUGH OPENING FOR
DRYWALL INSTALLATION
Stud Opening Dim. Frame
Rebate Width + 1 5/8"
Frame Rebate Height + 1"
JD
3.375"
1.875"
ADJUSTABLE FRAME - DRYWALL INSTALLATION INSTRUCTIONS
A
RMOR DOO
R
TM
1. Set Frame Throat Opening
Adjust each jamb and head to suit the measured wall thickness
2. Install Head
Slide the head into position in the center of the rough opening width. Wedges may be
used to temporarily hold the head in position
ADJUSTABLE FRAME - DRYWALL INSTALLATION INSTRUCTIONS
A
RMOR DOO
R
TM
3. Install Hinge Jamb
A. Insert the tabs on the jamb corner clips into the slots in the head
B. Pivot the jamb into place over the wall
C. Jamb corner clip tabs should go through the slots in the head rabbets and
returns
4. Install Strike Jamb
A. Repeat Steps 4A, 4B & 4C
ADJUSTABLE FRAME - DRYWALL INSTALLATION INSTRUCTIONS
A
RMOR DOO
R
TM
C. Place temporary spreader between the jambs at the floor and at the mid-height
of the fame to maintain correct frame rabbet width
D. Plumb and square the frame in the opening and, adjust for alignment and twist
5. Set frame
6. Anchor Frame
A. Apply screws to the head and jambs through the dimpled holes in each face.
B. Remove temporary spreader and re-check plumb, alignment and twist
A. Center the head in the rough opening
B. Bend the corner tabs extending through the head returns.
ADJUSTABLE FRAME - MASONRY INSTALLATION INSTRUCTIONS
A
RMOR DOO
R
TM
Stud Opening Dim. Frame
Rebate Width + 1 5/8"
Frame Rebate Height + 1"
ROUGH OPENING FOR
MASONRY INSTALLATION
3.375"
2"
VAR
1.875"
JD
.125"
FRAME OEPNING
STUD OPENING WIDTH =
FRAME OPENING + 1 5/8"
ROUGH OPENING WIDTH =
FRAME OPENING + 4 3/8" MIN.
Drywall
Masonry Wall
Wood Stud
Caulk if required
ADJUSTABLE FRAME - MASONRY
INSTALLATION INSTRUCTIONS
A
RMOR DOO
R
TM
1. Set Frame Throat Opening
Adjust each jamb and head to suit the measured wall thickness
2. Install Head
Slide the head into position in the center of the rough opening width. Wedges may be
used to temporarily hold the head in position
ADJUSTABLE FRAME - MASONRY
INSTALLATION INSTRUCTIONS
A
RMOR DOO
R
TM
3. Install Hinge Jamb
A. Insert the tabs on the jamb corner clips into the slots in the head
B. Pivot the jamb into place over the wall
C. Jamb corner clip tabs should go through the slots in the head rabbets and
returns
4. Install Strike Jamb
A. Repeat Steps 4A, 4B & 4C
ADJUSTABLE FRAME - MASONRY
INSTALLATION INSTRUCTIONS
A
RMOR DOO
R
TM
C. Place temporary spreader between the jambs at the floor and at the mid-height
of the fame to maintain correct frame rabbet width
D. Plumb and square the frame in the opening and, adjust for alignment and twist
5. Set frame
6. Anchor Frame
A. Apply screws to the head and jambs through the dimpled holes in each face.
B. Remove temporary spreader and re-check plumb, alignment and twist
A. Center the head in the rough opening
B. Bend the corner tabs extending through the head returns.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Armor Door VSDFDEX3680EL Installation guide

Brand
Armor Door
Model
VSDFDEX3680EL
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents