Heartland 16826 Installation guide

16826-W

STOP!

Call Us First!

DO NOT RETURN TO STORE.

For immediate help with assembly or product information

call our toll free number:

1-800-577-9663

or email:

customerservice@backyardproductsllc.com

Our staff is ready to provide assistance

April through October M-F 8:00 AM to 4:30 PM EST

Saturday 8:30 AM to 4:30 PM EST

November through March M - F 8:00 AM to 5:00 PM EST

(This page intentionally left blank.)

- CUSTOMER SERVICE -

Call: 1-800-577-9663 email: customerservice@backyardproductsllc.com

BEFORE YOU BEGIN

IMPORTANT!

READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.

•BUILDINGRESTRICTIONSANDAPPROVALS

Be sure to check with local building department and homeowners association for specic restrictions and/ or requirements before building.

. •ENGINEEREDDRAWINGS

Contact our Customer Service Team if engineered drawings are needed to pull local permits.

•SURFACEPREPARATION

To ensure proper assembly you must build your shed on a level surface. Recommended methods and materials to level your shed are

listed on page 7.

•CHECKALLPARTS

Inventory all parts listed on pages 4 - 6. Contact our Customer Service Team if any parts are missing or damaged.

•ADDITIONALMATERIALS

You will need additional materials to complete your shed. See page 3 for required and optional materials and quantities.

11/03/2015

KEEP THIS MANUAL FOR FUTURE REFERENCE

ACTUAL FLOOR SIZE IS 144" x 90" (365,8 x 228,6 cm)

16826-W

METROPOLITAN 12' x 7'-6" (365,8 x 228,6 cm)

ASSEMBLY MANUAL

A Backyard Products Company

2

TOOLS

Safety! Always use approved safety glasses during assembly.

OptionalRequired

HELPFUL REMINDER SYMBOLS

Look for these symbols for helpful reminders throughout this manual.

ORIENT LUMBER AND TRIM FOR BEST APPEARANCE

= Assistance Required; two or more people.

= Ensure squareness.

= Important required step or operation.

= Helpful assembly hint.

= Mark part with pencil.

= Beginning of steps for assembly or installation.

= You have  nished the assembly or installation.

= Level

❑ Gloves

Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.

Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way

negatively affect the strength or integrity of our product. (See Fig. A, B, C.)

A

❑ Safety Glasses

❑ Tape Measure

❑ Paint Tools

❑ Ladder

❑ Caulk Gun

❑ Hammer

❑ Level

FINISH

BEGIN

❑ Pencil

❑ Phillips

Screwdriver

❑ Drill / Driver

❑ 1/4" Drill Bit

❑ 3/8" Drill Bit

❑ 1/2" Drill Bit

❑ #2 Philips Drive Bit

❑ Tool Belt/

Nail Pouch

❑ Chalk Line

❑ Nail Gun

• gun nails

❑ Tin Snips

(for drip edge)

❑ Square

or

❑ Utility Knife

❑ Shingle Blades

B C

3

COMPLETING YOUR SHED

You will need these additional materials:

TO VALIDATE YOUR WARRANTY YOU MUST USE THE FOLLOWING:

FOUNDATION OR FLOOR MATERIALS

ADDITIONAL MATERIALS

DRIPEDGE.....................50Feet #15ROOFINGFELT

To cover 106 Sq. Ft. of roof area.

1"GALVANIZEDROOFINGNAILS.........1/4Lb

For roong felt.

REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S INSTRUCTIONS

FOR INSTALLATION OF SHINGLES, DRIP EDGE AND FELT.

3-TABSHINGLES.............................6Bundles

PAINTFORSIDING..........................2Gallons

Use 100% acrylic latex exterior paint. (2) coats recommended.

CAULK.................................................3Tubes

Use acrylic latex exterior caulk that is paintable.

1"GALVANIZEDROOFINGNAILS....3Lbs

For shingles.

PAINTFORTRIM.............................1Quart

Use 100% acrylic latex exterior paint.

WOODGLUE.......................ExteriorRated

REINFORCED WOOD FLOOR FRAME (OPTIONAL)

IMPORTANT! The included oor has been designed for general use. Depending on your specic use you may want to construct a

heavy duty oor frame by adding additional oor joists (shown below). Below is a list of additional materials (not included):

x3

x6

2 x 4 x 87" (5 x 10 x 221 cm) Treated Lumber

ea. 3" (7,6 cm) Hot Dipped Galvanized Nails

• This shed kit includes a complete wood oor system.

• This shed kit does not include ANY leveling materials.

• SeetheFLOORLEVELINGsectiononpage7forrecommendedmethodsandsuggestedmaterialstoproperlylevelyour

oor,asthiswillvarydependingonyourspecicsite.

Optional 12" (30,1 cm) spacing.

• Standard spacing is 16" (40,7 cm).

WOODSIZECONVERSIONCHART

NominalBoardSize ActualSize

1" x 4".................3/4" x 3-1/2" (1,9 x 8,9 cm)

2" x 4"..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)

2" x 3"..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)

1" x 3".................3/4" x 2-1/2" (3,8 x 6,3 cm)

PARTS IDENTIFICATION AND SIZES

RS

Part identication

letters are stamped on some parts.

Check these locations for

part stamp.

Treated lumber is stamped:

All treated lumber

is stamped:

WALLS

x4

2 x 4 x 86" (5,1 x 10,2 x 218,4 cm)

BLA

x2

2 x 4 x 80-11/16" (5,1 x 10,2 x 204,9 cm)

JDA

x2

2 x 4 x 75-3/8" (5,1 x 10,2 x 191,5 cm)

JCA

x2

2 x 4 x 86-1/4" (5,1 x 10,2 x 219,1 cm)

FHA

x2

2 x 4 x 68" (5,1 x 10,2 x 172,7 cm)

UM

PARTS LIST

INVENTORY YOUR PARTS before you begin.

We suggest sorting parts by the category they are listed in.

RAFTERS

TRIM

x2

1 x 3 x 33 - 1/8" (2,5 x 7,6 x 84,1 cm)

BPA

x7

2 x 4 x 64" (5,1 x 10,2 x 162,5 cm)

UX

x3

2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

SP

x2

2 x 4 x 40" (5,1 x 10,2 x 101,6 cm)

SKA

x2

2 x 3 x 33-1/8" (5,1 x 7,6 x 84,1 cm)

BQA

x4

19/32 x 2-1/2 x 9" (1,5 x 6,3 x 22,9 cm)

EY

x2

2 x 4 x 86-1/8" (5,1 x 10,2 x 203,5 cm)

JEA

3/4"

(1,9 cm)

2 x 4 x 16-1/2" (5,1 x 10,2 x 41,9 cm)

x8

RD

x2

2 x 4 x 57-5/8" (5,1 x 10,2 x 146,4 cm)

FGA

x1

1 x 3 x 5" (2,5 x 7,6 x 12,7 cm)

GAA

x11

2 x 3 x 10-1/2" (5,1 x 7,6 x 26,7 cm)

BRA

x2

1 x 3 x 72" (2,5 x 7,6 x 182,8 cm)

HJ

x11

2 x 4 x 93-3/16" (1,5 x 10,2 x 236,7 cm)

BOA

x2

19/32 x 3-1/2 x 48" (1,5 x 8,8 x 121,9 cm)

ZT

x1

19/32 x 3-1/2 x 59-1/4" (1,5 x 8,8 x 150,4 cm)

BXR

x1

19/32 x 3-1/2 x 59-1/4" (1,5 x 8,8 x 150,4 cm)

HBA

x1

19/32 x 3-1/2 x 59-1/4" (1,5 x 8,8 x 150,4 cm)

BXL

x1

19/32 x 3-1/2 x 60-3/8" (1,5 x 8,8 x 153,4 cm)

HHA

x1

UN

2 x 4 x 94-1/2" (5,1 x 10,2 x 240 cm)

x3

TP

2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

x1

19/32 x 3-1/2 x 24-3/8" (1,5 x 8,8 x 61,9 cm)

ZZ

4

FLOOR

x2

2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

2 x 4 x 87" (5,1 x 10,2 x 220,9 cm)

x10

x2

2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

SOFFIT

DOOR

PARTS LIST continued...

TRIM

CORNER/FREIZE TRIM

19/32 x 2-1/2 x 91" (1,5 x 6,3 x 231,1 cm)

x2

BSA

19/32 x 3-1/2 x 96" (1,5 x 8,8 x 243,8 cm)

x2

ZX

3/8 x 10-3/8 x 75-1/2" (1 x 26,3 x 191,8 cm)

x1

x2

OO

1-1/2 x 2-1/2 x 69" (3,8 x 6,3 x 175,2 cm)

19/32 x 2-1/2 x 26-5/8" (1,5 x 6,3 x 67,6 cm)

x2

AH

19/32 x 2-1/2 x 55-1/8" (1,5 x 6,3 x 140 cm)

x2

FDA

x1

3/8 x 2 x 72" (0,9 x 5,1 x 182,8 cm)

x1

3/8 x 2 x 73-3/8" (0,9 x 5,1 x 186,4 cm)

x1

3/8 x 2 x 69-1/4" (0,9 x 5,1 x 175,8 cm)

x1

3/8 x 2 x 69-1/4" (0,9 x 5,1 x 175,8 cm)

x2

3/8 x 2 x 91-1/4" (0,9 x 5,1 x 231,7 cm)

x1

3/8 x 2 x 93-1/4" (0,9 x 5,1 x 236,8 cm)

x1

3/8 x 2 x 93-1/4" (0,9 x 5,1 x 236,8 cm)

x2

3/8 x 2 x 68-3/4" (0,9 x 5,1 x 174,6 cm)

x2

19/32 x 2-1/2 x 41-1/4" (1,5 x 6,3 x 104,8 cm)

JFA

x2

19/32 x 2-1/2 x 24-3/8" (1,5 x 6,3 x 61,9 cm)

CY

x1

2 x 3 x 59-1/4" (5,1 x 7,6 x 150,5 cm)

GKA

x1

PT

2 x 3 x 96" (5,1 x 7,6 x 243,8 cm)

x2

OY

2 x 3 x 72" (5,1 x 7,6 x 182,8 cm)

x1

3/8 x 10-3/8 x 79-5/8" (1 x 26,3 x 202,2 cm)

x2

3/8 x 5-1/4 x 95-1/2" (1 x 13,3 x 242,5 cm)

5

PANEL PARTS LIST

ROOF PANELS

FLOOR

NOTE:Panelpartsarenotstamped.

Floorpanelsare5/8"(1,6cm)thick.Roofpanelsare7/16"(1,1cm)thick.

7/16 x 11-7/8 x 96"

(1,1 x 30,2 x 243,8 cm)

x2

7/16 x 11-7/8 x 60-1/8"

(1,1 x 30,2 x 152,7 cm)

x1

7/16 x 48 x 96"

(1,1 x 121,9 x 243,8 cm)

x3

5/8 x 42 x 96"

(1,5 x 106,6 x 243,8 cm)

5/8 x 48 x 90"

(1,5 x 106,6 x 228,6 cm)

x1

5/8 x 48 x 96"

(1,5 x 121,9 x 243,8 cm)

x1

WALL PANEL & DOORS PARTS LIST

x1

LEFTDOOR

x1

RIGHTDOOR

x2

BOXES

x4

BOXES

NAIL BOXES (not included)

VENTS / DOOR HARDWARE / WINDOWS

FASTENER/HARDWARE BAG

x1

3/8 x 42 x 96"

(1 x 106,7 x 243,8 cm)

x1

3/8 x 48 x 96"

(1 x 121,9x 243,8 cm)

x1

3/8 x 48 x 96"

(1 x 121,9x 243,8 cm)

x3

3/8 x 48 x 72"

(1 x 113,3 x 121,9 cm)

x1

3/8 x 48 x 84"

(1 x 122 x 213,4 cm)

x1

3/8 x 48 x 84"

(1 x 122 x 213,4 cm)

x1

3/8 x 42 x 96"

(1 x 106,7 x 243,8 cm)

x2

3/8 x 23-7/8 x 96"

(1 x 60,6 x 243,8 cm)

6

x255 2" (5,1 cm)

3" (7,6 cm)

x85

x76

x123

x4

1-1/4" (3,2 cm)

3/4" (1,9 cm)

2" (5,0 cm)

3" (7,6 cm)

2" (5,1 cm)

x180

1-1/2" (3,8 cm)

x2

8 x 16"

(20,3 x 35,6 cm)

x2

1-1/2" (3,8 cm)

1/2" (1,2 cm)

x12

x1

64" Metal Threshold

3/4" (1,9 cm) x11

Bagged separately / special coating

x2

Window

16-1/4" x 22-1/4"

(41,3 x 56,5 cm)

x3

9 X 27" (22,8 x 68,5 cm)

x1

x4

3/4”TechScrewwithdrillpoint

1-1/4” x8

3-PointDoorLockingMechanism

x1

1-1/4” x2

Handle(locking)

with Screws

x11

H2.5

Tie Plate

7

DOOR

FLOOR LEVELING OPTIONS

There are multiple ways to level your oor frame. Our recommended leveling method is shown below.

Leveling materials are not included in this kit.

PREFERRED METHOD - 4x4 TREATED RUNNERS

Measurements to

centerof4x4's.

• 3" Screws angled into 4x4.

• (2) at each point frame

• and 4x4 touch.

• Level under 4x4 runners only.

• Locate leveling material 12" from ends of runners and no more than 48" apart.

• Asphalt shingles should be used between 4x4 runners and blocks or treated lumber. Never use

shingles in direct contact with ground.

• For best results and aiding in water drainage use gravel under each concrete block.

LEVELINGMETHODS

• If you are building your shed on a concrete foundation see the following page.

CONCRETE

MATERIALREQUIRED

x2

4" x 4" x 12' (10 x 10 x 365,8 cm)Treated Lumber

FastenersforFrameto4"x4".

(3" Screws shown as one option.) Minimum (40) 3" screws / exterior grade.

Useonlywoodtreatedforgroundcontactandfastenersapprovedforusewithtreatedwood.

Alwayssupportframeseams.

Levelinghigherthan16"notrecommended.

LEVELINGMATERIALS

Gravel

2x4 Treated Lumber

Solid Masonry Blocks in 1", 2", 4" or 8" thickness

Asphalt Shingles

8" Block

4" Block

Gravel

Do not exceed 16".

4x4 Runner

Shingle

Maximum between leveling

material locations.

48"

12"

2x4 Treated Lumber

2" Block

Level

12"

(30,5 cm)

12"

(30,5 cm)

8

CONCRETE FOUNDATION

Your kit contains all materials to construct a wooden oor. If you choose to install your kit

on a concrete slab refer to the diagram below.

• A treated 2 x 4" (5,1 x 10,2 cm) sill plate is required when installing your shed on concrete. Hint:Usetreatedlumberinyourkitor

purchasefulllengthtreatedlumber.

• Use a high quality exterior grade caulk beneath all sill plates.

• Fasten 2 x 4" (5,1 x 10,2 cm) sill plates to slab using approved concrete anchors (fastenersnotincluded).

• Check local code for concrete foundation requirements.

NOTES

Allow new concrete slabs to cure for at least seven (7) days.

2" x 4" x 12'-0" (5,1 x 10,2 x 365,8 cm)

2" x 4" x 7'-6" (5,1 x 10,2 x 229,6 cm)

Caulk

Requires:

x2

x1

MUSTbetreatedlumber.

144"(365,8cm)

144"x90"(365,8x228,6cm)

83"(210,9cm)

12'x7'-6"(365,8x228,6cm)

90"(228,6cm)

AActualSize B CBuildingSize

A

B

C

4"

(10,2 cm)

3-1/2"

(8,9 cm)

DOOR

Treated Sill Plate

Caulkbetweensill

plateandconcrete.

9

x10

x2

3" (7,6 cm)

x44

2 x 4 x 87" (5,1 x 10,2 x 221 cm)

2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

x2

2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

PARTSREQUIRED:

Center

onmarks

DOOR

FLOOR FRAME

Look for

Stamp

TREATED

HINT:

For easier nailing

standonframe.

2

1

Use two 3" nails at each mark.

Orient parts as shown on  at surface. Measure and mark.

BEGIN

You have  nished your  oor frame. Proceed to level and square frame.

FINISH

3

FlushFlush

TOENAILING

48"

(121,9 cm)

48"

(121,9 cm)

32"

(81,3 cm)

16"

(40,6 cm)

48"

(121,9 cm)

64"

(162,6 cm)

80"

(203,2 cm)

90"

(228,6 cm)

87"

(221 cm)

96"

(243,8 cm)

112"

(284,5 cm)

128"

(325,1 cm)

144"

(365,8 cm)

96"

(243,8 cm)

10

FINISH

5

LEVEL AND SQUARE FLOOR FRAME

Before attaching  oor decking, it is important to level and square the  oor frame.

A level and square  oor frame is required to correctly construct your shed.

BEGIN

2

3

4

1

Use level and check the frame is level before applying  oor panels.

Check for frame squareness by measuring diagonally across corners. If the measurements are the

same, the frame is square. The diagonal measurement will be approximately 169-13/16" (431,3 cm).

When the frame is level and square secure one side of frame to the 4x4 runners using one fastener at

ends of each runner. Move to the opposite end of the frame. Secure the frame to 4x4 runners with one

fastener at ends of each runner making sure the frame remains square

(Fig.A).

Once the  oor frame is level and square fasten the frame to the 4x4 runners at each point the frame

contacts the 4x4 runners.

See page 7 for the preferred  oor leveling method.

DOOR

First,secure

at ends with

onefastener.

Second,secure

at ends with

onefastener.

169-13/16"

(431,3 cm)

169-13/16"

(431,3 cm)

Fig.A

11

48"

(121,9 cm)

144"

(365,8 cm)

6"

(15,2 cm)

12"

(30,5 cm)

Move to the opposite side. Using the long edge of the panel as a lever, move the

panel side-to-side until the top corner is ush to the oor frame (Fig.B).

Secure panel with two 2" nails in the corners.

2

BEGIN

1

3

4

Continue attaching the panel using 2" nails 6" apart on

edges and 12" apart inside panel.

Use a chalk line or use pre-painted grid lines to nail

into joists under panel.

Ensureyouroorframeissquarebyinstallingonepanel

andsquaringframe.

Fig.A

Check the oor frame is square by measuring diagonally

across the frame corners. If the measurements are the

same your oor frame is square. The measurement will

be approximately 169-13/16" (431,3 cm) (Fig.C).

PARTSREQUIRED:

x1

x50

5/8 x 48 x 96"

(1,6 x 121,9 x 243,8 cm)

Gridlinesup

Seam

2" (5,1 cm)

Flush

(2)Nails

FLOOR PANELS

3/4"

(1,9 cm)

Fig.B

Flush

(2)Nails

3/4"

(1,9 cm)

Attach the 48 x 96" panel with the rough side up (painted-grid lines side) with the 48"

edge and corner ush to the oor frame (FigA). Secure panel with two 2" nails in the

corners.

DOOR

Fig.C

DOOR

169-13/16"

(431,3 cm)

169-13/16"

(431,3 cm)

DOOR

12

42"

(106,7 cm)

90"

(228,6 cm)

144"

(365,8 cm)

6"

(15,2 cm)

48"

(122 cm)

12"

(30,5 cm)

PARTSREQUIRED:

FINISH

7

You have  nished attaching your  oor panels.

Continue installing panels with rough side up (painted grid lines).

Use grid lines on panel for 2" nails 6" apart on edges, and 12" apart inside panels.

5

7

6

x1 x1

x91

5/8 x 48 x 90"

(1,6 x 60,6 x 122 cm)

5/8 x 42 x 96"

(1,6 x 106,7 x 243,8 cm)

Gridlinesup

2" (5,1 cm)

FLOOR PANELS

Flush

DOOR

Flush

13

DOOR

Backwall

Front wall

Checktheoorframeislevelafterinstallingoorpanels.

Re-levelifneeded.

HINT:

IMPORTANT!

•Theoorshouldbeusedasastableworksurfaceforwallconstruction.

• Organizeyourassemblyprocedureduringthebuildprocess

 toavoidover-handlingofthewalls.

DOOR

BACK WALL FRAME

PARTSREQUIRED:

HINT:

For easier nailing

standonframe.

x2

2 x 4 x 96" (5,1 x 10,2 x 243,8 cm)

TP

x7

2 x 4 x 64" (5,1 x 10,2 x 162,5 cm)

UX

x2

2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)

SP

x32

14

3" (7,6 cm)

BEGIN

1

Use two 3" nails at each mark and four 3" nails at seams

Orient parts on edge on oor. Measure and mark.

2

UXx7

TP

SP

TP

144"

(365,8 cm)

120"

(304,8 cm)

64"

(162,5 cm)

1-1/2"

(3,8 cm)

96"

(243,8 cm)

96"

(243,8 cm)

48"

(122 cm)

72"

(182,9 cm)

48"

(122 cm)

24"

(61 cm)

96"

(243,8 cm)

TOENAILING

3"(7,6cm)

Nails

15

BACK WALL PANELS

48 x 72"

(121,9 x 213,4 cm)

PARTSREQUIRED:

x1

x45

2" (5,1 cm)

Fig.B

Fig.A

3/4"

(1,9 cm)

3/4"

(1,9 cm)

2 Nails

Place 48x72" panel onto wall frame with primed side up as shown.

Use the gauge block to mark the 3/4" measurement on the wall stud. Secure panel with

two 2" nails in the corners (Fig.A).

Nail the panel using 2" nails 6" apart on edges and 12" apart inside panel.

•Ensureyourwallframeissquarebyinstallingonepanelandsquaringframe.

Move to the opposite end. Using the long edge of the panel as a lever move the panel side-to-side until you have

a 3/4" measurement on the wall stud. Secure corner with two 2" nails (Fig.B).

4

5

3

3/4"GAUGE

BLOCK

GAA

Primed

side up

Forsquarenessmaintain3/4"

measurementalongpaneledges.

BEGINHERE

3/4"GAUGE

BLOCK

•Ensuretopofpanelisoverhangingthetopofframeby4".

6"

(15,2 cm)

4"

(10,2cm)

3/4"

(1,9 cm)

3/4"

(1,9 cm)

48"

(121,9 cm)

12"

(30,5 cm)

16

48"

(121,9 cm)

3/4"

(1,9 cm)

4"

(10,2 cm)

3/4"

(1,9 cm)

12"

(30,5 cm)

6"

(15,2 cm)

48"

(121,9 cm)

4"

(10,2 cm)

12"

(30,5 cm)

6"

(15,2 cm)

Place center 48"x72" panel on frame

as shown with primed side facing up.

Nail using 2" nails 6" apart on edges

and 12" apart inside panel.

6

Place end 48"x72"panel on frame as

shown with primed side facing up.

Nail using 2" nails 6" apart on edges

and 12" apart inside panel.

7

You have  nished building your back wall.

FINISH

9

48 x 72"

(121,9 x 213,4 cm)

x2

x90

BACK WALL PANELS

PARTSREQUIRED:

2" (5,1 cm)

8

Carefully  ip the BACK wall over.

3/4"GAUGE

BLOCK

GAA

3/4"GAUGE

BLOCK

Flush

Primed

side up

Primed

side up

Forsquarenessmaintain3/4"

measurementalongpaneledges.

Forsquarenessmaintainush

alongpaneledges.

17

FRONT WALL FRAME

PARTSREQUIRED:

HINT:

For easier nailing

standonframe.

x2

2 x 4 x 68" (5,1 x 10,2 x 172,7 cm)

UM

x1

2 x 4 x 57-5/8" (5,1 x 10,2 x 146,4 cm)

FGA

x4

2 x 4 x 86" (5,1 x 10,2 x 218,4 cm)

BLA

x1

2 x 4 x 86-1/4" (5,1 x 10,2 x 219,1 cm)

FHA

x1

2 x 4 x 94-1/2" (5,1 x 10,2 x 240 cm)

UN

2 x 4 x 40" (5,1 x 10,2 x 101,6 cm)

x2

SKA

2 x 4 x 16-1/2" (5,1 x 10,2 x 42 cm)

x1

RD

x34

3" (7,6 cm)

BEGIN

1

Use two 3" nails at each mark and four 3" nails at seams.

For front wall, orient parts on edge on oor. Measure and mark.

2

Flush

39"

(99,1 cm)

24"

(61 cm)

16-1/2"

(42 cm)

40"

(101,6 cm)

40"

(101,6 cm)

24"

(61 cm)

24"

(61 cm)

16"

(40,6 cm)

16"

(40,6 cm)

57-5/8"

(146,4 cm)

84-7/8"

(215,6 cm)

94-1/2"

(240,1 cm)

89"

(226,1 cm)

69-1/2"

(176,5 cm)

86-1/4"

(219,1 cm)

144"

(365,8 cm)

120"

(304,8 cm)

104-1/2"

(265,4 cm)

BLA

x4

UM

x2

UN

RD

FHAFGA

SKASKA

64"

(162,6cm)

18

FRONT WALL FRAME

PARTSREQUIRED:

HINT:

For easier nailing

standonframe.

2 x 4 x 16-1/2" (5,1 x 10,2 x 41,9 cm)

x3

RD

x12

3" (7,6 cm)

Use two 3" nails at each mark.

Orient parts on edge as shown. Measure and mark.

3

4

64"

(162,6cm)

You have  nished building your front wall frame.

FINISH

5

27-1/2"

(69,9 cm)

115-3/8"

(293,1 cm)

57-3/8"

(145,7 cm)

28-3/8"

(72,1 cm)

27-1/2"

(69,9 cm)

27-1/2"

(69,9 cm)

RDx3

Page is loading ...

Heartland 16826 Installation guide

This manual is also suitable for

Heartland 16826 Installation guide

Related papers

Other documents