1
Dynex FM Transmitter
DX-MP3FM
Contents
Introduction.........................................................1
Using the transmitter...........................................1
Specifications.......................................................3
Legal notices........................................................3
Français ..................................... 5
Español.....................................10
Introduction
You can use this wireless FM stereo transmitter to play your favorite
music through your car stereo, home stereo, or any other audio device
with an FM receiver. Just plug the transmitter into the headphone
jack of any portable audio source (including MP3 players like an iPod
®
,
CD players, and tape players), then tune the frequency of the car or
home stereo to a frequency that the transmitter uses. You can then sit
back and enjoy your favorite music with full stereo sound and
ultimate convenience.
Using the transmitter
To use the transmitter:
1 Remove the battery cover and insert two AAA batteries. Make
sure that the batteries are inserted correctly according to the
diagram on the inside of the battery case.
DX-MP3FM transmitter.fm Page 1 Thursday, September 1, 2005 2:18 PM
2
2 Replace the battery cover. Make sure that the cover is securely
in place.
3 To turn on the transmitter, press and hold the power
button for two seconds. The transmitter turns on.
4 Press +/- to choose a channel, then connect the transmitter to
an audio source.
5 Turn on both the audio source and the FM receiver (FM radio),
then tune your receiver to the same frequency as the
transmitter. The music from the audio source is played on your
FM radio.
Tip: The audio source can be any audio device that accepts a
3.5 mm stereo jack, so a portable CD player, MP3 player,
MD player, computer, PDA, television, and even another FM
radio can be the audio source. Since the range of the transmitter
can vary widely depending on the presence of other electronic
devices, building materials, terrain, and distance, you should
experiment on your own to determine its useful range for your
use.
6 To turn off the transmitter, press and hold the power button
for two seconds.
Programming frequencies into the transmitter
In addition to the preset frequencies, you can program any of the ten
memory channels to any frequency from 88.1~107.9MHz.
To program or change a frequency on the
transmitter:
1 To turn on the transmitter, press and hold the power
button for two seconds. The most recent frequency the
transmitter used is selected and active.
DX-MP3FM transmitter.fm Page 2 Thursday, September 1, 2005 2:18 PM
3
2 Press +/- to select the frequency you want to store in a
memory location.
3 Press and hold the memory button for about two seconds.
M1 begins flashing on the display.
4 Press +/- to select the memory location you want to store the
frequency in (M1-M10), then press
memory to save the
frequency in that location.
To select a frequency to transmit to:
1 Press memory repeatedly to select the frequency you want.
The selection moves from M1-M10.
Specifications
Frequency range.........................88.1~107.9 MHz
Memory locations..............................................10
Power source ......................2 AAA batteries (1.5V)
or DC 5V auto charger (optional)*
* When you plug DC power (the auto charger) into the FM
transmitter, the transmitter uses only power from the DC power
source. Using DC power prolongs the life of your batteries
without damaging the transmitter.
Legal notices
© 2005 Dynex. DYNEX and the DYNEX logo are trademarks of Best
Buy Enterprise Services, Inc. Other brands and product names are
trademarks or registered trademarks of their respective holders.
Specifications and features are subject to change without notice or
obligation.
DX-MP3FM transmitter.fm Page 3 Thursday, September 1, 2005 2:18 PM
4
FCC notices
Warning: Changes or modifications to this FM transmitter not
expressly approved by Dynex can void your authority to operate
the transmitter.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: 1) this device may not cause
harmful interference, and 2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is needed.
• Consult the dealer or an experienced radio/TV technician for
help.
DX-MP3FM transmitter.fm Page 4 Thursday, September 1, 2005 2:18 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
15
DX-MP3FM transmitter.fm Page 15 Thursday, September 1, 2005 2:18 PM
16
www.dynexproducts.com (800) 305-2204
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
Distribué par Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 É.-U.
Distribuido por Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
R5
DX-MP3FM transmitter.fm Page 16 Thursday, September 1, 2005 2:18 PM
/