Honda 08E02-SHJ-100B User manual

Brand: Honda

Model: 08E02-SHJ-100B

Type: User manual

Honda 08E02-SHJ-100B

This accessory HandsFreeLink allows you to connect to your vehicle's audio system wirelessly. With this device you can make and receive calls, stream music, and control your music player, all without taking your hands off the wheel.

The HandsFreeLink is easy to install and use. Simply follow the included instructions and you'll be up and running in no time. Once installed, you'll be able to enjoy all the benefits of hands-free calling and music streaming.

Here are just a few of the features of the Honda 08E02-SHJ-100B:

Make and receive calls wirelessly
Stream music from your phone or other Bluetooth-enabled device

Honda 08E02-SHJ-100B

Here are just a few of the features of the Honda 08E02-SHJ-100B:

Make and receive calls wirelessly
Stream music from your phone or other Bluetooth-enabled device

INSTALLATION

INSTRUCTIONS

Accessory Application Publications No.

Issue Date

2008 ODYSSEYAccessory HandsFreeLink

PARTS LIST

HFL Attachment Kit

P/N 08E02-SHJ-100B

HFL trim

HFL harness

2 Double-faced tapes

HFL bracket

HFL subharness

HFL retainer

Template

Fuse label

Fuse (2 A)

6 EPT sealers

8 Wire ties

4 Self-tapping screw, 3 x 10 mm

2 Washer screws, 4 x 12 mm

AII 38137-38714

JAN 2008

Self-tapping screw

Bush

Ground bolt

Rubber bumper

www.collegehillshonda.com

7518071E

TOOL AND SUPPLIES REQUIRED

#2 Phillips screwdriver

10 mm Combination wrench

10 mm and 14 mm Socket

Pushpin

Ratchet

3 mm, 4.5 mm, 6 mm, 9 mm, and 10 mm Drill bit

Eye protection (face shield, safety goggles, etc.)

File

Diagonal cutters

Scissors

Masking tape

Tape measure

Cardboard

Isopropyl alcohol

Shop towel

19 mm Holesaw

Drill

Utility knife

T15 Torx bit

Felt-tip pen

Illustration of the HFL Installed on the Vehicle

CONTOROL

UNIT

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by

skilled technicians who have the proper tools,

equipment, and training to correctly and safely add

equipment to your vehicle. These procedures

should not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for the

radio, then write down the frequencies for the

preset buttons.

2. Disconnect the negative cable from the battery.

Control unit

HFL Blue Tooth Kit

P/N 08E00-E10-100

Switch

SWITCH

HFL

HARNESS

HFL

SUBHARNESS

FUSE

(2 A)

Accessory User's Information Manual

Plastic trim tool SILTRIMTL10

www.collegehillshonda.com

3. Disengage eight retaining tabs and remove left

and right lens from the roof console.

7. Using a flat-tip screwdriver, push the hook and

turn the holder. Remove the holder.

7517010E

ROOF

CONSOLE

RIGHT

LENS

4 RETAINING

TABS

LEFT

LENS

4 RETAINING

TABS

VEHICLE

CONNECTORS

SUNGLASS

HOLDER

(Open.)

2 BOLTS

4. Open the sunglass holder.

5. Remove four bolts and lower the roof console.

6. Disconnect the two vehicle connectors and

remove the roof console.

2 BOLTS

8. Disengage two screws and remove the left

sunvisor.

9. Pull away the weatherstrip from the left front A-

pillar trim. Release the side curtain air bag clip by

using the plastic trim tool and remove the left front

A-pillar (two clips).

SIDE CURTAIN

AIR BAG CLIP

CLIP

WEATHERSTRIP

LEFT FRONT

A-PILLAR TRIM

PLASTIC TRIM

TOOL

LEFT

SUNVISOR

VEHICLE

CONNECTOR

2 SCREWS

COVER

RETAINING

TAB

SUNVISOR

HOLDER

PLASTIC TRIM TOOL

www.collegehillshonda.com

7517042E

4301210B

13. Plug the HFL subharness 6-pin connector into the

6-pin opening in the fuse box.

12. Attach the fuse label (2 A) to the fuse case of the

HFL subharness.

4301221B

3 CLIPS

LEFT FRONT

DOOR SILL TRIM

3 CLIPS

LEFT KICK

PANEL

HFL

SUBHARNESS

6-PIN

CONNECTOR

FUSE

BOX

10. Remove the left front door sill trim (three clips).

11. Pull away the weatherstrip from the left kick panel.

Remove the left kick panel (three clips).

7821100B

FUSE LABEL (2 A)

HFL

SUBHARNESS

HFL

SUBHARNESS

FUSE CASE

WEATHERSTRIP

www.collegehillshonda.com

7517051E

7517072E

7517031E

NOTE: If another accessory is already plugged into the

6-pin connector, remove the dummy connector

from the 6-pin connector taped to the HFL

subharness. Plug the 6-pin connector from the

other accessory harness into the 6-pin

connector from the HFL subharness you just

unplugged and plug the HFL subharness into

the fuse box.

VEHICLE

HARNESS

VEHICLE

CLIP

GREEN

TAPE

WIRE

TIE

HFL

SUBHARNESS

VEHICLE

HARNESS

HFL

SUBHARNESS

4319060B

14. Route the HFL subharness to the left front pillar

trim opening.

FUSE BOX

HFL

SUBHARNESS

6-PIN

CONNECTOR

OTHER ACCESSORY

6-PIN CONNECTOR

DUMMY

CONNECTOR

16. Remove the vehicle bolt (discard) and install the

ground bolt with HFL subharness ground terminal

as shown.

17. Disconnect the vehicle harness 1-pin connector

and connect it to the HFL subharness 1-pin

connector.

VEHICLE

BOLT

(Discard.)

GROUND

BOLT

HFL SUBHARNESS

GROUND TERMINAL

FUSE

BOX

HOOD

OPENER

18. Connect the HFL subharness 1-pin connector to

the vehicle 1-pin connector.

19. Wrap the cut one half of the EPT sealer on the

HFL subharness connection part.

FUEL

OPENER

HFL SUBHARNESS

1-PIN CONNECTOR

VEHICLE

HARNESS 1-PIN

CONNECTOR

EPT

SEALER

HFL

SUBHARNESS

LEFT FRONT

PILLAR TRIM

OPENING

HFL SUBHARNESS

CONNECTION PART

EPT

SEALER

Cut in half.

15. Route the HFL subharness and secure the

harness to the vehicle harness with a wire tie

above the vehicle clip as shown.

www.collegehillshonda.com

7517091E

7517101E

7517061E

23. Cut the template into template A and template B.

24. Remove the damper (two tapping screws).

SUNGLASSES

HOLDER

ROOF

CONSOLE

DAMPER

2 TAPPING

SCREWS

TEMPLATE A

TEMPLATE B

TEMPLATE

VEHICLE

BUSHES

TAPPING

SCREW

CAMSET

LOCK

2 RETAINING

TABS

25. Remove the sunglasses holder (tapping screw and

vehicle bushes).

26. Remove the pin and remove the camset lock (two

retaining tabs).

21. Using isopropyl alcohol on a shop towel, clean the

area where the EPT sealer will attach. Attach a

EPT sealer to secure the HFL subharness to the

vehicle panel.

22. Secure the HFL subharness to the vehicle

harness with three wire tie.

20. Secure the HFL subharness to the vehicle

harness with a wire tie.

7517080E

3 WIRE

TIES

HFL

SUBHARNESS

VEHICLE

HARNESS

WIRE TIE

HFL

SUBHARNESS

VEHICLE

PANEL

VEHICLE

HARNESS

EPT

SEALER

www.collegehillshonda.com

7517112E

7716020X

7523030E

27. Remove the console light from the roof console

(four retaining tabs).

CONSOLE

LIGHT

ROOF

CONSOLE

4 RETAINING

TABS

7524060E

ROOF

CONSOLE

DRILL BIT

(9 mm)

28. Enlarge the hole on the roof console with 9 mm

drill bit.

29. Attach masking tape to the roof console as

shown.

30. Attach template A with masking tape to the roof

console at the indicated position.

PUSHPIN

2 MARKS

TEMPLATE A

ROOF

CONSOLE

ROOF

CONSOLE

MASKING

TAPE

FELT-TIP

PEN

MASKING

TAPE

31. Using a felt-tip pen, mark the center of the roof

console as shown.

32. Use a pushpin to mark the roof console at two

locations according to template A.

33. Remove template A.

MARK

CENTER OF THE

ROOF CONSOLE

www.collegehillshonda.com

7517131E

7517141E

35. Attach template B with masking tape on the roof

console at the indicated position.

34. Drill 4.5 mm holes at the two locations marked on

the roof console in step 32. After drilling, remove

any burrs.

7517120E

DRILL BIT

(4.5 mm)

2 MARKS

ROOF

CONSOLE

PUSHPIN

FELT-TIP

PEN

MASKING

TAPE

TEMPLATE B

ROOF

CONSOLE

4 MARKS

39. Drill a 3 mm hole at the four locations marked on

the roof console in step 36.

DRILL BIT

(3 mm)

DRILL BIT

(3 mm 6 mm

10 mm)

19 mm

HOLE SAW

4 MARKS

ROOF

CONSOLE

DRILL

40. Enlarge the two 3 mm holes drilled in step 39 with

a 6 mm drill bit and with a 10 mm drill bit as

shown.

41. Enlarge the other two 3 mm holes drilled in step

39 with a 19 mm hole saw as shown.

36. Use a pushpin to mark the roof console at four

locations according to template B.

37. Use a felt-tip pen and mark the roof console along

the template B.

38. Remove template B.

CENTER OF THE

ROOF CONSOLE

www.collegehillshonda.com

7517152E

7517171E

7517161E

43. Remove the masking tape attached in step 29.

44. Using isopropyl alcohol on a shop towel, clean the

areas where the double-faced tape will attach.

Remove the adhesive backing from double-faced

tape and attach the double-faced tape at the

indicated position on the control unit.

45. Connect the HFL harness 22-pin connector to the

control unit.

7517180E

2 DOUBLE-FACED

TAPES

CONTROL

UNIT

10 mm

CONTROL

UNIT

CENTER

CONTROL

UNIT

CONTROL

UNIT

ROOF

CONSOLE

Remove the

adhesive

backing.

ROOF

CONSOLE

HFL HARNESS

22-PIN

CONNECTOR

HFL

HARNESS

HFL

BRACKET

2 WASHER

SCREWS,

4 x 12 mm

ROOF

CONSOLE

Holes drilled

in step 34.

46. Using isopropyl alcohol on a shop towel, clean the

areas where the double-faced tape will attach.

Remove the adhesive backing from the double-

faced tape attached to the control unit and attach

to the roof console at the indicated position.

47. Use the holes drilled in step 34 and secure the

HFL bracket with two 4 x 12 mm washer screws to

the roof console.

ROOF

CONSOLE

Cut out.

Mark made in

step 37.

42. Using a utility knife, cut along the marking made

on the roof console in step 37. After cutting,

remove any burrs.

ROOF

CONSOLE

Cut out.

UTILITY

KNIFE

www.collegehillshonda.com

791209AB

7517192E

48. Bend the switch terminal as shown.

51. Connect the HFL harness 20-pin connector to the

switch.

7518010E

52. Install the switch assembled in step 50 to the roof

console with self-tapping screw, bushes, tapping

screw removed in step 25 and vehicle bushes.

53. Reinstall the console light to the roof console.

54. Using isopropyl alcohol on a shop towel, clean

the area where the EPT sealer will attach. Cut an

EPT sealer in half and attach one half to the

vehicle bracket as shown.

HFL TRIM

SWITCH

HFL

RETAINER

4 SELF-TAPPING

SCREWS,

3 x 10 mm

SELF- TAPPING

SCREW

BUSHES

SWITCH

ROOF

CONSOLE

VEHICLE

BRACKET

EPT SEALER

(Cut in half.)

EPT SEALER

ROOF CONSOLE

OPENING

HFL HARNESS

20 -PIN

CONNECTOR

HFL

RETAINER

RUBBER

BUMPER

SELF- TAPPING

SCREW (Reuse.)

VEHICLE

BUSHES

(Reuse.)

49. Insert the rubber bumper to the HFL retainer.

50. Assemble HFL retainer, switch, and HFL trim with

four 3 x 10 mm self-tapping screws.

SWITCH

TERMINAL

BACKSIDE OF THE SWITCH

SWITCH

TERMINAL

(Bend.)

SPEAKER

www.collegehillshonda.com

7518042E

2219080T

7518020E

55. Hold the roof console close to the roof console

opening and connect the HFL harness 4-pin

connector to the HFL subharness 4-pin connector.

58. Connect the vehicle connectors to the roof

console. Reinstall the roof console with the four

bolts from step 5.

59. Install the fuse (2 A) into the fuse box at the

indicated position.

7518030E

3 EPT

SEALERS

ROOF

PANEL

HFL

SUBHARNESS

2 BOLTS

ROOF

CONSOLE

VEHICLE

CONNECTORS

FUSE (2 A)

FUSE BOX

ROOF

CONSOLE

ROOF

CONSOLE

OPENING

GREEN

CONNECTOR

WIRE TIE

VEHICLE

BRACKET

Vehicle front

HFL

SUBHARNESS

4-PIN

CONNECTOR

HFL HARNESS

4-PIN

CONNECTOR

56. Secure the connector with a wire tie to the vehicle

bracket.

57. Using isopropyl alcohol on a shop towel, clean the

area where the EPT sealer will attach. Secure the

HFL subharness to the vehicle roof panel inside

the roof lining with three EPT sealers.

2 BOLTS

www.collegehillshonda.com

2219090T

61. Check that all wire harnesses are routed properly

and that all connectors are plugged in.

62. Reinstall all removed parts.

63. Reconnect the negative cable to the battery.

64. Enter the customer’s radio anti-theft code, and

reset the radio station presets.

65. Reset the clock.

NOTE: When the battery is disconnected, the driver’s

window AUTO function is disabled.

• Start the engine. Push down on the driver’s window

switch until the window is fully open.

• Pull up on the driver’s window switch to close the

window completely, then hold the switch for

1 second or more.

• Lower and raise the driver’s window to check

operation of the driver’s window AUTO function.

60. Attach the fuse label to the No. 33 slot on the fuse

box cover.

FUSE BOX

COVER

FUSE LABEL

(OPITION FUSE 2 A)

No. 33

www.collegehillshonda.com

Honda 08E02-SHJ-100B User manual

Brand: Honda

Model: 08E02-SHJ-100B

Type: User manual

Honda 08E02-SHJ-100B

Here are just a few of the features of the Honda 08E02-SHJ-100B:

Make and receive calls wirelessly
Stream music from your phone or other Bluetooth-enabled device

Download PDF

report

Honda 08E02-SHJ-100B User manual

Honda 08E02-SHJ-100B User manual

Related papers

Other documents