Honda 76410-SZA-A01 Installation guide

Honda
Brand
Honda
Model
76410-SZA-A01
Type
Installation guide
Publications No.
Issue Date
INSTALLATION
INSTRUCTIONS
Accessory Application
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-35 (1707) 1 of 4
08V03-TG7-1000-90
VERSION 1
AUTOMATIC DAY/NIGHT
MIRROR
2018 RIDGELINE
JUL 2017
PARTS LIST
Automatic Day/Night Mirror Attachment Kit
P/N 76410-SZA-A01
Harness cover
Service Parts
Automatic Day/Night mirror
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
10 mm Open end wrench
T20 TORX bit
Small flat-tip screwdriver
Shop towel
The following tool is available through the Honda Tool and
Equipment Program. On the iN, click on Service > Service
Bay > Tool and Equipment Program, then enter the
number under “Search.” Or, call 888-424-6857.
• Trim Tool Set (T/N SOJATP2014)
• Plastic Trim Tool (T/N SILTRIMTL10)
Illustration of the Automatic Day/Night Mirror in the
Vehicle
AUTOMATIC DAY/NIGHT
MIRROR
2 of 4 AII06945-35 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
1. Wrap a shop towel around the hood latch.
• Remove the front bulkhead cover.
• Remove the intake air tube.
• Disconnect the negative cable from the battery.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-35 (1707) 3 of 4
2. Remove the roof console.
• Using a small flat-tip screwdriver wrapped with a
shop towel, pry out and remove the left and right
lens.
• Open the sunglass holder and remove the four
screws.
• Remove the roof console and unplug the vehicle
connectors.
VEHICLE
CONNECTORS
ROOF
CONSOLE
4 SCREWS
4 RETAINING
TABS
LEFT LENS
RIGHT LENS
4 RETAINING
TABS
3. Loosen the TORX screw, and remove the rear view
mirror.
MIRROR
MOUNT
REARVIEW
MIRROR
(Discard.)
T20 TORX
BIT
MIRROR
MOUNT
TORX SCREW
(Loosen.)
4. Install the automatic day/night mirror on the mirror
mount as shown, and tighten the TORX screw.
TORX SCREW
(Tighten.)
T20 TORX
BIT
MIRROR
MOUNT
AUTOMATIC
DAY/NIGHT
MIRROR
MIRROR
MOUNT
5. Remove the tape from the headliner, and release the
vehicle 7-pin connector.
VEHICLE
7-PIN CONNECTOR
TAPE
VEHICLE
7-PIN
CONNECTOR
TAPE
(Remove.)
VEHICLE
7-PIN
CONNECTOR
HEADLINER
4 of 4 AII06945-35 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
6. Route the vehicle harness as shown, and plug the
vehicle 7-pin connector into the automatic day/night
mirror. Be careful not to crease the headliner.
AUTOMATIC DAY/
NIGHT MIRROR
HEADLINERSLOT
VEHICLE
HARNESS
AUTOMATIC DAY/
NIGHT MIRROR
VEHICLE
7-PIN CONNECTOR
7. Secure the harness cover to the mirror mount. Slide
the harness cover behind the headliner.
Slide.
HEADLINER
HARNESS
COVER
VEHICLE
HARNESS
HARNESS
COVER
MIRROR
MOUNT
HEADLINER
HARNESS
COVER
SECTION
VIEW
WINDSHIELD
8. Check that all wire harnesses are routed properly
and all connectors are plugged in.
9. Install all removed parts except for the front
bulkhead cover and the intake air tube.
10. Connect the negative cable to the battery.
11. Install the front bulkhead cover and the intake air
tube.
12. Press and hold the audio unit power button for two
seconds to restore the audio and navi (if equipped)
system functions.
13. Set the clock on vehicle without navigation.
NOTE: Check the operation of the automatic day/night
mirror according to the owner’s manual.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Honda 76410-SZA-A01 Installation guide

Honda
Brand
Honda
Model
76410-SZA-A01
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents