2. V-ZUG
  3. 31032
31032

V-ZUG 31032 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the V-ZUG 31032 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Validity
These installation instructions apply to the following models: 31032 (GK35TEPSC)
General notes
If installing into a combustible material, the guidelines and standards for low voltage installations and fire protection must be
strictly observed.
Identification plate
The identification plate is located next to the connection
plate.
Affix the second identification plate (supplied) in an
accessible position behind the front of the fitted
cabinet beneath the appliance.
Identification plate
Connection plate
Installation accessories supplied
Designation Article no.
Mounting angle front/back H6.3279
Wood screws for mounting angle Diverse
Accessories
Designation Article no.
Thermal shielding plate set H6.3266
Instant adhesive for installation in stone worktops
Permabond F246 (incl. activator), 50 ml tube. From Silitech AG, 3008 Berne.
B11.502
Adjusting brace set for special installation cases H6.1548
Installation instructions
J31032.113-1
17.04.14
Glass ceramic hob Toptronic
With normal mounting frame
1
Electrical connection
Electrical connections must be carried out by trained electricians in accordance with the guidelines and standards for low-
voltage installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug
and socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles
switching are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors
ensure safe and fault-free operation. After installation, live parts and cables with basic insulation must not be accessible.
Check old installations.
The appliance is designed for use up to a max. altitude of 2000 m above sea level.
See the identification plate for information on the necessary mains voltage, type of current and fuse protection.
The appliance is equipped with a mains cable that should be connected to a distribution box by the customer.
600/550
900
Installation pipeClamp Distribution box
brown + black
blue
yellow/green
black
blue
yellow/green
brown
L2
L1
N
N
L1
PE/
PE/
400 V 2N~
230 V~
Installation
The distance from the appliance cut-out to combustible walls (left, right, rear) must be at least 50 mm. Parts such as side
walls and reinforcing strips which protrude into the installation space under the cooking zone must be made of non-combus-
tible materials.
The distance between the underside of the appliance tray and any part of the cabinet beneath that is made of combustible
material must be at least 20 mm. If a drawer is installed directly underneath – and if the tray can be reached from below
without the aid of tools – touch protection must be used. The thermal shielding plate set (see ’Accessories’) is recommended
for this purpose.
Indications
• The worktop must be flat.
• A cabinet unit with a width of 900 mm is recommended for the base unit.
Installation instructions
J31032.113-1
17.04.14
Glass ceramic hob Toptronic
With normal mounting frame
2
Fitting
The layout of the cooking zones on the hob to be built in may differ from the illustrated hob!
Y – Y
Y
Y
444
774
≥ 30
750 ±1
≥ 20
420 ±1
C
A
A
B
825
≥ 70
≥ 70
42.5
from support
Aim for a
≤ R10
Set of fixing brackets for
special installation cases
Drawer/cabinet
Cable length 1.7 m
Centering mark, front
Centering mark, rear
The underside of the material between cut-outs front and rear is reinforced.
The width of material between cut-outs is determined by the producer of the stone worktop.
The minimum material width can vary according to the property of the stone.
For wood worktops
1. Create an accurate cut-out.
2. Centre mounting rails A and B and fix into the installation cut-out with the wood screws C according to the drawing.
3. Where necessary establish the mains supply connection before inserting the appliance.
4. Lower the appliance symmetrically into the installation cut-out to level with the worktop and onto the catch spring elements. The
connection cable must not touch any hot parts of the tray beneath the cooking zones.
For stone worktops
For stone worktops, mounting rails A and B can be adhered in position (for adhesive, see ’Accessories’).
1. Clean and prime the surfaces of the stone and the mounting rails to which the adhesive is to be applied. Allow to dry.
2. Apply the adhesive to the stone and smooth with a spatula. Apply a thin layer of activator to the adhered surface of the mounting
rails.
3. Centre the mounting rails and press down well. Observe the recommended bonding time for the adhesive used.
4. Where necessary establish the mains supply connection before inserting the appliance.
5. Lower the appliance symmetrically into the installation cut-out to level with the worktop and onto the catch spring elements. The
connection cable must not touch any hot parts of the tray beneath the cooking zones.
Installation instructions
J31032.113-1
17.04.14
Glass ceramic hob Toptronic
With normal mounting frame
3
/