Honda 08A15-1E1-100 User manual

Brand: Honda

Model: 08A15-1E1-100

Category: Car video systems

Type: User manual

This manual is also suitable for

INSTALLATION

INSTRUCTIONS

Accessory Application Publications No.

Issue Date

08B15-S9V-1001-91

The XM Radio system will not fit in a vehicle

equipped with a navigation system or a rear

entertainment system.

PARTS LIST

XM Radio Attachment Kit (sold separately):

P/N 08B15-S9V-100

15 Wire ties

XM radio harness

Unit bracket

DIN cable

5 Wire ties with clips

Double-sided adhesive tape,

53 x 28 mm

6 Washer-screws, 4 x 8 mm

4 Washer-bolts, 6 x 12 mm

2 Cushion tapes

7 EPT sealers

Fuse label

2 Subantenna cables

Harness hook (Not used)

4 Flange nuts, 4 mm

AII 25886

2003-2004 PILOT

XM RADIO SYSTEM

Display module pocket

Clip nut

3 Self-tapping screws

AUG 2003

2 Washer-screws, 4 x 12 mm

(Not used)

Double-sided adhesive tape,

60 x 60 mm

Antenna plate

www.collegehillshonda.com/parts

Display module

Receiver unit

Owner’s Manual

DIN Bezel (sold separately):

P/N 08B23-S9V-100A

FM modulator unit

XM Antenna Kit (sold separately):

P/N 08A15-1E1-100

TOOL AND SUPPLIES REQUIRED

#2 Phillips screwdriver

Flat-tip screwdriver

Utility knife

Diagonal cutters

Push pin

Tape measure

Shop towel

Scissors

Ratchet

8 mm, 10 mm, and 14 mm Sockets

8 mm, 10 mm, and 14 mm Combination wrenches

Felt-tip pen

Isopropyl alcohol

Drill

3 mm and 10 mm drill bits

Eye protection (face shield, safety goggles, etc.)

Antenna

Base Kit (sold separately):

P/N 08A15-1E1-000

DIN bezel

Illustration of an Installed XM Radio System

3121110M

DISPLAY

MODULE

MODULATOR

UNIT

ANTENNA

RECEIVER UNIT

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by

skilled technicians who have the proper tools,

equipment, and training to correctly and safely add

equipment to your vehicle. These procedures should

not be attempted by “do-it-yourselfers.”

VEHICLE

20-PIN

CONNECTOR

VEHICLE

ANTENNA

CABLE

SUBANTENNA

CABLE

XM RADIO

HARNESS

DISPLAY

MODULE

FM MODULATOR

UNIT

ANTENNA

RECEIVER UNIT

DIN CABLE

2N27010M

1. Make sure you have the anti-theft code for the

radio, then write down the frequencies for the

preset buttons.

2. Disconnect the negative cable from the battery.

3. Using a flat-tip screwdriver wrapped with a shop

towel, gently pry out on the audio panel to remove

the five clips. Unplug the connectors, and remove

the audio panel.

AUDIO PANEL

CLIPS (5)

VEHICLE

CONNECTOR

AUDIO UNIT

6. Remove the center panel (four self-tapping screws

and two clips, and unplug the vehicle accessory

power outlet).

7. If equipped with a cigarette lighter, remove the four

self-tapping screws. Pull the center panel by

releasing the two clips. Unplug the two lighter

harness terminals, and remove the illumination

light. Remove the center panel.

DRIVER’S CENTER

CONSOLE TRIM

PASSENGER’S

CENTER

CONSOLE TRIM

CLIPS (3)

CLIPS (2)

SELF-

TAPPING

SCREWS

VEHICLE

CONNECTOR

CENTER

PANEL

4. Remove the four screws that fasten the audio

bracket. Pull the audio unit out toward you, and

unplug the vehicle connector and antenna cable

from the rear of the audio unit. If equipped with a

cassette/in-dash CD changer, unplug the

additional connectors.

5. Remove the driver’s and passenger’s center

console trim pieces (three clips each). Take care

not to damage the clips.

AUDIO UNIT

VEHICLE CONNECTOR

(If equipped, unplug the

additional connectors.)

ANTENNA

CABLE

AUDIO

BRACKET

AUDIO

BRACKET

SCREW

(Reuse.)

LIGHT HOLDER

ILLUMINATION

LIGHT

LIGHTER

HARNESS

TERMINALS

CLIPS (2)

CIGARETTE

LIGHTER

CENTER

PANEL

SELF-

TAPPING

SCREWS (4)

With Cigarette Lighter:

8. Remove the four screws that fasten the left and

right vehicle bracket. Pull the heater control unit

and pocket toward you, and unplug the vehicle

connectors.

Clean with

isopropyl alcohol.

3121040M

Clean with

isopropyl alcohol.

DISPLAY

MODULE

POCKET FLANGE

DOUBLE-SIDED

ADHESIVE TAPE

DISPLAY

MODULE

DISPLAY

MODULE

POCKET

CLIP NUT

ADHESIVE

BACKINGS

10. Slide the clip nut onto the display module pocket

flange.

3131010M

RIGHT

VEHICLE

BRACKET

SCREW

HEATER

CONTROL UNIT

VEHICLE

CONNECTOR

LEFT

VEHICLE

BRACKET

SELF-

TAPPING

SCREW

LEFT VEHICLE

BRACKET

HEATER

CONTROL UNIT

POCKET

RIGHT VEHICLE

BRACKET

SELF-

TAPPING

SCREW

SELF-

TAPPING

SCREW

(Reuse.)

SELF-TAPPING SCREW

(Reuse.)

9. Remove the left and right vehicle brackets (six

self-tapping screws), and separate the heater

control unit from pocket. Set the pocket aside, it

will not be reused.

11. Attach the display module to the display module

pocket:

• Using isopropyl alcohol on a shop towel, clean

the center of the back of the display module

where the double-sided adhesive tape will

attach.

• Remove on backing from the double-sided

adhesive tape, and attach it to the display

module.

• Remove the remaining backing from the

double-sided adhesive tape. Route the display

module cable through the hole of the display

module pocket, and attach the display module

to the pocket.

14. Fit the DIN bezel around the display module

pocket. Set the heater control unit on the display

module pocket, and reinstall the left and right

vehicle brackets using the two self-tapping screws

removed in step 9. Attach the display module to

brackets with three self-tapping screws supplied

with the XM radio attachment kit.

Routing the XM Radio Harness

15. Remove the driver’s seat front cover (four clips).

16. Remove the driver's seat rear cover (four clips).

Take care not to damage the clips.

CLIPS (4)

DRIVER’S

SEAT FRONT

COVER

DRIVER’S

SEAT

17. Remove the drivers seat (four bolts). Move the

driver seat out of the way.

DRIVER’S SEAT

BOLTS (4)

DRIVER’S SEAT

REAR COVER

CLIPS (4)

DRIVER’S SEAT

HEATER

CONTROL

UNIT

3121051M

SELF-

TAPPING

SCREW

(Reuse.)

RIGHT

VEHICLE

BRACKET

LEFT

VEHICLE

BRACKET

SELF-TAPPING

SCREWS

(Supplied with

XM radio

attachment kit)

SELF-TAPPING

SCREWS

(Supplied with

XM radio

attachment

kit)

SELF-

TAPPING

SCREW

(Reuse.)

DISPLAY

MODULE

POCKET

DIN

BEZEL

20. Route the XM radio harness and two subantenna

cables from the dashboard opening to driver’s

floor. Using one cushion tape, attach it to the

vehicle frame.

CLIPS (7)

DRIVER’S CENTER

CONSOLE LOWER

COVER

DRIVER’S

SEAT

18. On the driver’s side of the vehicle, remove the

center console lower cover (gently pull the cover

out toward you to release the seven clips). Take

care not to damage the clips.

3121031M

Use

these

labels.

FUSE LABEL

FUSE CASE

FUSE

LABEL

(2A)

XM RADIO

HARNESS

SUBANTENNA

CABLE

DASHBOARD

OPENING

Align.

50 mm

CUSHION TAPE

19. Get the XM radio harness, the subantenna cables,

and the fuse labels. Attach the 2A and 5A fuse

labels to the fuse cases on the XM radio harness.

21. Pull the XM radio harness and subantenna cables

out through the dashboard opening approximately

50 mm.

FUSE

LABEL

(5A)

Clean with

isopropyl

alcohol.

22. Plug the audio unit vehicle 20-pin connector into

the XM radio 20-pin connector that is blue-taped to

the XM radio harness. Wrap one EPT sealer

around the subantenna cable in the area shown.

25. Place the display module/heater control unit

assembly near the dashboard opening, and route

the display module cable along the XM radio

harness and the subantenna cables.

23. Plug the vehicle antenna cable into the

subantenna cable.

EPT

SEALER

SUBANTENNA

CABLE

XM RADIO

HARNESS 20-PIN

CONNECTOR

SUBANTENNA

CABLE

VEHICLE 20-PIN

CONNECTOR

VEHICLE

ANTENNA

CABLE

3131021M

VEHICLE ANTENNA

CABLE

XM RADIO

HARNESS

WIRE TIE

SUBANTENNA

CABLE

FRAME

PIPE

VEHICLE

HARNESS

24. Secure the XM radio harness and subantenna

cables to the vehicle harness with a wire tie.

DISPLAY MODULE/HEATER

CONTROL UNIT ASSEMBLY

DISPLAY MODULE

CABLE

EPT SEALER

VEHICLE FRAME

(Clean with

isopropy

alcohol.)

26. Using isopropyl alcohol on a shop towel, clean the

vehicle frame, then attach one EPT sealer on the

edge of the vehicle frame to protect the cables.

27. Remove the two screws from the side brackets at

the heater control unit opening. Plug in the heater

control unit connectors, and slide the display

module/heater control unit assembly into the

dashboard opening. Reinstall the two side bracket

screws, and the four heater control unit screws

removed in step 8.

SCREW

(reused)

SCREW

(reused)

SCREWS

(Removed

in step 8.)

XM RADIO HARNESS

SUBANTENNA CABLES

DISPLAY MODULE

CABLE

DISPLAY MODULE/HEATER

CONTROL UNIT ASSEMBLY

28. Plug the XM radio harness 20-pin connector and

sub antenna cable into the audio unit, and

carefully slide the audio unit into the dashboard.

Reinstall the four audio unit screws.

29. Secure the XM radio harness, subantenna cables,

and display module cable to the vehicle pipe with

two wire ties.

30. Continue routing cables through the center

console and toward the rear of the vehicle. Using

scissors, cut one cushion tape in half. Clean the

vehicle frame with isopropyl alcohol, and attach

half of the cushion tape to the vehicle frame in the

area shown.

DISPLAY

MODULE

CABLE

XM RADIO

HARNESS

WIRE

TIES

VEHICLE

PIPE

DISPLAY MODULE

CABLE

SCREW (4)

(reused)

AUDIO

UNIT

XM RADIO

HARNESS 20-PIN

CONNECTOR

SUBANTENNA

CABLE

SUBANTENNA

CABLE

2N27130M

CUSHION

TAPE

XM RADIO

HARNESS

VEHICLE FRAME

(Clean with

isopropyl alcohol.) VEHICLE

HARNESS

CUSHION

TAPE

Cut.

SUBANTENNA

CABLE

DISPLAY MODULE

CABLE

VEHICLE

HARNESS

WIRE TIE

XM RADIO

HARNESS

SUBANTENNA

CABLE

VEHICLE FRAME

(Clean with

isopropyl alcohol.)

DISPLAY MODULE

CABLE

CUSHION

TAPE

31. Secure the XM radio harness and subantenna

cables with one wire tie, but don’t tighten the wire

tie at this time.

32. Attach the remaining half of the cushion tape to

the vehicle frame in the area shown.

36. Remove the dashboard side cover (four clips, one

retaining tab, and seven hooks).

HOOKS (7)

DASHBOARD

SIDE COVER

CLIPS (4)

RETAINING

TAB

34. Route the XM radio harness and subantenna

cables under the floor carpet and out the slit.

Secure the cables with one wire tie.

Installing the Antenna

35. On the driver's side of the vehicle, remove the

weatherstrip from the left front door opening in the

area shown, then remove the left front "A" pillar

trim (two clips).

33. Measure and slit the driver’s floor carpet in the

area shown. Be careful not to damage the

subantenna cables and XM radio harness when

cutting the floor carpet.

CLIPS (2)

WEATHERSTRIP

LEFT FRONT

"A" PILLAR TRIM

FLOOR

CARPET

slit

50 mm

XM RADIO

HARNESS

SUBANTENNA

CABLE

DISPLAY MODULE

CABLE

WIRE TIE

37. Remove the fuel lid door opener lever, then

remove the left front door sill trim (three clips and

two retaining tabs).

38. Remove the weatherstrip from the left kick panel.

Remove the upper clip from the left kick panel,

then pull the left kick panel out toward you to

release the retaining clip.

39. Get two EPT sealers. Using scissors, cut two

EPT sealers into six pieces. Wrap the them

around the antenna unit cable at the

measurements shown.

40. Using isopropyl alcohol on a shop towel, clean the

bottom of the antenna unit. Remove the backing

from the 60 x 60 mm double-sided adhesive tape,

and attach it to the bottom of the antenna unit.

CLIP

LEFT KICK

PANEL

WEATHERSTRIP

CLIPS (2)

CLIP

FUEL LID DOOR

OPENER LEVER

RETAINING

TAB

LEFT

FRONT

DOOR SILL

TRIM

ANTENNA UNIT

CABLE

ADHESIVE

BACKING

(Remove.)

ANTENNA

UNIT

ANTENNA

PLATE

Clean with

isopropyl alcohol.

EPT SEALER

60 x 60 mm

DOUBLE-SIDED

ADHESIVE TAPE

Cut.

ANTENNA

UNIT

ADHESIVE

BACKING

(Remove.)

41. Using isopropyl alcohol on a shop towel, clean the

areas where the antenna unit and the antenna

plate will attach.

42. Remove the adhesive backing from the antenna

unit and the antenna plate, and attach them to the

dashboard in the area shown.

ADHESIVE

BACKING

(Remove.)

DASHBOARD

60 mm

200 mm

45. Secure the antenna unit cable to the vehicle

harness with two wire ties.

46. Below the dashboard, secure the antenna unit

cable to the vehicle harness with two additional

wire ties.

43. Route the antenna unit cable along the front

windshield and the top of the dashboard. Insert the

antenna unit cable with the EPT seals between

the windshield and the dashboard.

44. Route the antenna unit cable down and under the

dashboard.

2N27040M

ANTENNA UNIT

CABLE

2N27050M

ANTENNA

UNIT CABLE

WIRE

TIES

VEHICLE

HARNESS

2N27060M

ANTENNA

UNIT CABLE

ANTENNA

UNIT CABLE

WIRE

TIE

VEHICLE

HARNESS

WIRE

TIE

VIN IDENTIFICATION

PLATE

(Don’t hide the VIN

number with the

antenna unit cable.)

Insert.

DASHBOARD

ANTENNA

UNIT

CABLE

Route under the

dashboard.

FRONT

WINDOW

GLASS

Insert.

ANTENNA

UNIT CABLE

2N27080M

47. Continue routing the antenna unit cable alongside

the vehicle harness, and out through the hole in

the floor carpet under the driver's seat. Secure the

antenna unit cable to the vehicle harness with four

wire ties in the area shown.

Installing the Receiver Unit and FM Modulator Unit

48. Install the receiver unit to the unit bracket with the

four 4 x 8 mm washer-screws, and four 4 mm

flange nuts.

49. Install the FM modulator unit tn the unit bracket

with the two 4 x 8 mm washer-screws.

50. Get the DIN cable. Plug the DIN cable into the FM

modulator unit and the receiver unit.

MODULATOR

UNIT

BRACKET

4 x 8 mm

WASHER-

SCREWS (4)

RECEIVER

UNIT

4 mm

FLANGE

NUTS (4)

4 x 8 mm

WASHER-

SCREWS (2)

MODULATOR

UNIT

RECEIVER UNIT

DIN CABLE

UNIT

BRACKET

2N27070M

ANTENNA

UNIT CABLE

WIRE TIES

FLOOR

CARPET

VEHICLE

HARNESS

VEHICLE

HARNESS

HOLE

MODULATOR

UNIT

RECEIVER UNIT

ANTENNA

UNIT CABLE

SUB

ANTENNA

CABLE

SUBANTENNA

CABLE

XM RADIO

HARNESS

3-PIN

CONNECTOR

4-PIN

CONNECTOR

FRONT

MODULATOR

UNIT

CABLES

51. Position the unit assembly under the driver’s seat.

Plug the XM radio harness 4-pin connector and

the antenna unit cables into the receiver unit. Plug

the XM radio harness 3-pin connector, the display

module cable, and the subantenna cables into the

FM modulator unit.

52. Wrap one EPT sealer around the subantenna

cables.

EPT SEALER

DISPLAY

MODULE

CABLE

2N27090M

WIRE

TIE

WITH

CLIP

WIRE

TIE

WITH

CLIP

WIRE

TIE

WIRE

TIE

ANTENNA

UNIT CABLE

XM RADIO

HARNESS

MODULATOR

ANTENNA

CABLE

WIRE TIES

WITH CLIPS

ANTENNA UNIT

CABLE

(Bundle the

excess cable.)

SUBANTENNA

CABLE

DISPLAY

MODULE

CABLE

2N27100M

6 x 12 mm

WASHER-

BOLTS (4)

UNIT BRACKET

DRIVER’S SEAT

SEAT RAIL

MODULATOR

UNIT

53. Get the five wire ties with clips and two wire ties.

Secure all of the cablse to the unit bracket in the

order shown:

XM radio harness, subantenna cables, and the

display module cable.

XM radio harness, subantenna cables, and the

display module cable.

Antenna unit cable, XM radio harness,

subantenna cable, and the display module

cable.

Subantenna cable and FM display unit cable.

FM modulator unit cable and the antenna unit

cable.

55. Slide the driver's seat forward, and install the unit

bracket to the driver’s seat rails using four

6 x 12 mm washer-bolts. Tighten the bolts

securely.

56. Check that all of the wire harnesses are routed

properly and all of the connectors are plugged in.

57. Reconnect the negative cable to the battery.

58. Set one of the radio station presets to FM 88.7

and check the operation of the XM radio. If

necessary, use the XM radio Owner’s Manual

supplied.

59. Reinstall the driver’s seat. Take care not to pinch

the display module cable. Torque the seat bolts to

47 N·m (35 lbf·ft).

60. Reinstall all of the removed parts.

61. Enter the customer’s radio anti-theft code, and

reset the radio station presets.

62. Set the clock.

NOTE: Whenever the battery is disconnected,

the driver’s window AUTO up function is disabled.

63. Start the engine. Push down on the driver’s

window switch until the window is fully open.

64. Pull up on the driver’s window switch and close

the window completely, then hold the switch up

for at least 2 seconds or more.

65. Test the window AUTO up function.

Honda 08A15-1E1-100 User manual

Brand: Honda

Model: 08A15-1E1-100

Category: Car video systems

Type: User manual

This manual is also suitable for

Download PDF

report

Honda 08A15-1E1-100 User manual

This manual is also suitable for

Honda 08A15-1E1-100 User manual

Related papers

Other documents