Vantec UGT-PCE20SR User manual

Brand: Vantec

Model: UGT-PCE20SR

Category: Interface cards/adapters

Type: User manual

Vantec UGT-PCE20SR is a 2-port serial PCIe host card that allows you to add two RS-232 serial ports to your computer. It is compliant with PCI Express Specification 1.1 and supports x1, x4, x8, and x16 PCI Express bus. The card has a built-in 16C950 compatible UART and 128-byte FIFO for transmit/receive per port, and supports data transfer rates up to 230400bps. The UGT-PCE20SR is plug-n-play, and the I/O address and IRQ are assigned by the BIOS. It supports Windows XP/Vista/7/8 (32/64 bit) operating systems.

Vantec UGT-PCE20SR is a 2-port serial PCIe host card that allows you to add two RS-232 serial ports to your computer. It is compliant with PCI Express Specification 1.1 and supports x1, x4, x8, and x16 PCI Express bus. The card has a built-in 16C950 compatible UART and 128-byte FIFO for transmit/receive per port, and supports data transfer rates up to 230400bps. The UGT-PCE20SR is plug-n-play, and the I/O address and IRQ are assigned by the BIOS. It supports Windows XP/Vista/7/8 (32/64 bit) operating systems.

2-Port Serial (RS-232) PCIe

Host Card

User Manual

Model: UGT-PCE20SR

All brand names and trademarks are properties of their respective owners

www.vantecusa.com

UGT-PCE20SR Page 2

Contents

Features and Benefits ......................................................... 3

System Requirements ......................................................... 3

Package Contents ............................................................... 3

Hardware Installation ......................................................... 3

Driver Installation .............................................................. 4

UGT-PCE20SR Page 3

Features and Benefits

 Compliant with PCI Express Specification 1.1

 Supports x1, x4, x8, x16 PCI Express Bus

 Support 2 x UART serial ports

 Built-in 16C950 compatible UART

 128-byte FIFO for transmit/receive per port

 Data transfer rate up to 230400bps

 Plug-n-Play, I/O address and IRQ assigned by BIOS

 Support Windows XP/Vista/7/8

System Requirements

 Windows® XP/Vista/7/8 (32/64 bit)

 One available PCI Express slot

Package Contents

 1 x 2-Port Serial (RS-232) PCIe Host Card

 1 x Driver CD

 1 x User Manual

 2 x Low Profile Brackets

Hardware Installation

1. Turn off the power to your computer.

2. Unplug the power cord and remove your computer’s cover.

UGT-PCE20SR Page 4

3. Remove the slot bracket from an available PCIe slot.

4. To install the card, carefully align the card’s bus connector with

the selected PCIe slot on the motherboard. Push the board down

firmly.

5. Replace the slot bracket’s holding screw to secure the card.

6. Secure the computer cover and reconnect the power cord.

Driver Installation

1. Place the Driver CD into the CD-ROM drive. Click the Start

button on the taskbar and click Run. Type “D:\UGT-PCE20SR\

Windows\Setup.exe”. (Assuming you have placed the CD in

CD-ROM drive labeled as D).

2. Follow any on-screen instructions to complete the software

installation.

3. Restart your system.

4. Once you have rebooted the computer, this 2-Port Serial (RS-232)

PCIe Host Card is ready to be used.

1
2
3
4

Vantec UGT-PCE20SR User manual

Brand: Vantec

Model: UGT-PCE20SR

Category: Interface cards/adapters

Type: User manual

Vantec UGT-PCE20SR is a 2-port serial PCIe host card that allows you to add two RS-232 serial ports to your computer. It is compliant with PCI Express Specification 1.1 and supports x1, x4, x8, and x16 PCI Express bus. The card has a built-in 16C950 compatible UART and 128-byte FIFO for transmit/receive per port, and supports data transfer rates up to 230400bps. The UGT-PCE20SR is plug-n-play, and the I/O address and IRQ are assigned by the BIOS. It supports Windows XP/Vista/7/8 (32/64 bit) operating systems.

Download PDF

Related papers

Other documents