Vantec UGT-PCE20PL User manual

Vantec
Brand
Vantec
Model
UGT-PCE20PL
Category
Interface cards/adapters
Type
User manual

Vantec UGT-PCE20PL is a 2-Port Parallel PCIe Host Card that allows you to add two IEEE 1284 Parallel Ports to your system, providing faster data rates of up to 1.5Mbytes/sec. It supports Standard Parallel Port (SPP), Enhanced Parallel Port (EPP), and Enhanced Capability Port (ECP), making it compatible with a wide range of devices such as printers, scanners, and storage devices. The card is compliant with PCI Express Base Specification 1.1 and supports x1, x4, x8, and x16 PCI Express slots.

Vantec UGT-PCE20PL is a 2-Port Parallel PCIe Host Card that allows you to add two IEEE 1284 Parallel Ports to your system, providing faster data rates of up to 1.5Mbytes/sec. It supports Standard Parallel Port (SPP), Enhanced Parallel Port (EPP), and Enhanced Capability Port (ECP), making it compatible with a wide range of devices such as printers, scanners, and storage devices. The card is compliant with PCI Express Base Specification 1.1 and supports x1, x4, x8, and x16 PCI Express slots.

2-Port Parallel PCIe
Host Card
User Manual
Model: UGT-PCE20PL
All brand names and trademarks are properties of their respective owners
www.vantecusa.com
UGT-PCE20PL Page 2
Contents
Features and Benefits ............................................................. 3
System Requirements ............................................................ 3
Package Contents ................................................................... 3
Hardware Installation ............................................................ 3
Driver Installation .................................................................. 4
UGT-PCE20PL Page 3
Features and Benefits
Compliant with PCI Express Base Specification 1.1
Supports x1, x4, x8, x16 PCI Express
Add two IEEE 1284 Parallel Ports on system
Supports Standard Parallel Port (SPP), Enhanced Parallel (EPP)
& Enhanced Capability Port (ECP)
Faster data rates up to 1.5Mbytes/sec
Plug-n-Play, I/O address and IRQ assigned by BIOS
Support Windows XP/Vista/7/8
System Requirements
Windows XP/Vista/7/8 (32/64 bit)
One available PCI Express slot
Package Contents
1 x 2-Port Parallel PCIe Host Card
1 x Driver CD
1 x User Manual
1 x Bracket with one DB25 female parallel port
2 x Low Profile Brackets
Hardware Installation
1. Turn off the power to your computer.
2. Unplug the power cord and remove your computer’s cover.
UGT-PCE20PL Page 4
3. Remove the slot bracket from an available PCIe slot.
4. To install the card, carefully align the card’s bus connector with
the selected PCIe slot on the motherboard. Push the board down
firmly.
5. Replace the slot bracket’s holding screw to secure the card.
6. Secure the computer cover and reconnect the power cord.
Driver Installation
1. Place the Driver CD into the CD-ROM drive. Click the Start
button on the taskbar and click Run. Type “D:\UGT-PCE20PL\
Windows\Setup.exe”. (Assuming you have placed the CD in
CD-ROM drive labeled as D).
2. Follow any on-screen instructions to complete the software
installation.
3. Restart your system.
4. Once you have rebooted the computer, this 2-Port Parallel PCIe
Host Card is ready to be used.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Vantec UGT-PCE20PL User manual

Vantec
Brand
Vantec
Model
UGT-PCE20PL
Category
Interface cards/adapters
Type
User manual

Vantec UGT-PCE20PL is a 2-Port Parallel PCIe Host Card that allows you to add two IEEE 1284 Parallel Ports to your system, providing faster data rates of up to 1.5Mbytes/sec. It supports Standard Parallel Port (SPP), Enhanced Parallel Port (EPP), and Enhanced Capability Port (ECP), making it compatible with a wide range of devices such as printers, scanners, and storage devices. The card is compliant with PCI Express Base Specification 1.1 and supports x1, x4, x8, and x16 PCI Express slots.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents