Anova rcp6 Assembly Instruction

Brand: Anova

Model: rcp6

Category: Computer desks

Type: Assembly Instruction

anovafurnishings.com

888.535.5005 tel

TOOLS NEEDED:

• Ratchet with 9/16" socket

• T25 Torx screw driver

• T30 Torx screw driver

• Phillips head screw driver

• Hammer

Assembly Instructions

Recycled

RCP6 - 6' Rectangular Picnic Table, Recycled Plastic Legs

TABLE COMPONENTS:

ASSEMBLY HARDWARE:

(3) Table Top Planks

(2) Seat Planks (2) Seat Stieners (2) Seat Supports (2) Le Legs (2) Right Legs (2) Leg Mount Braces

(2) Angle

Brace Mounts

(2) Leg Mounts (2) Angle

Braces

(2) Angle

Supports

(2) Support Bars

(22) Torx T30 X 3"

Washer Head Screws

(8) T25 X 3" Torx

Head Screws

(20) T25 X 2 1/2"

Torx Head Screws

(60) #10 X 3/4"

Phillips Screws

(16) 3/8"-16 X 3 1/2"

Carriage Bolts

(16) 3/8" Flat

Washers

(16) 3/8" Lock

Washers

(16) 3/8"-16

Hex Nuts

ASSEMBLY:

Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.

2. Lay all parts on a so work surface or on the shipping packaging to prevent damage to nish.

3. Lay the three table top planks out on the padded work area. The table top planks can be distinguished from the seat planks because the

table top planks have four predrilled holes and four inner pilot holes while the seat planks have ve predrilled holes. Arrange the table top

planks with the four inner pilot holes facing up.

4. Locate the two angle brace mounts. Use the T25 Torx screw driver to

start six T25 x 2 1/2” torx screws into the predrilled holes in one of

the angle brace mounts. Drive the screws into the brace mount until

the points emerge on the other side. Place the angle brace mount

over one of the inner rows of predrilled pilot holes in the table top

planks, aligning the points of the torx screws with the pilot holes.

Use the T25 Torx screw driver to drive the screws into the table top

planks until tight.

NOTE: Before assembling the nuts to the bolts, it is recommended that a light oil or petroleum jelly be applied to the screw threads.

6' Rectangular Picnic Table, Recycled Plastic Legs

The assembly is a two-person operation.

T25 X 2 1/2" Torx

Head Screw

Angle Brace Mounts

5. Repeat Step 4 to attach the remaining angle brace mount.

6. Install a support bar along the inside edge of one of the angle brace mounts.

Place the support bar on the table top rst, then slide it against the angle

brace mount. Make sure the support bar maintains contact with the table

top. Drive six #10 X 3/4" Phillips screws through the holes in the support

bar, into the angle brace mount.

Install the remaining support bar against the other angle brace mount in the

same manner.

7. Set the table top aside on a padded surface.

8. Locate a le leg and a right leg and insert 3/8"-16 X 3 1/2" carriage bolts through the two holes closest to the thick ends. Insert the

bolts from the single-layer side toward the double-layer side. Use the hammer to seat the bolts. Lay the legs out in an “A” shape with

the thick leg ends facing up.

9. Repeat Step 8 to put together the other pair of legs and seat

support.

10. Locate the leg mounts. Place one of them at the top of each set of legs. Insert 3/8"-16 X 3 1/2" carriage bolts through the mounting

holes near the top of each leg and through the matching holes in the leg mounts. Use the hammer to seat the carriage bolt and expose

the threads. Place a 3/8" at washer, 3/8" lock washer and 3/8"-16 hex nut on the end of each carriage bolt and tighten nger tight.

11. Install the leg mount brace along the lower edge of the leg

mount. The face of the brace with 6 holes should be installed

on the wide face of the leg mount. Use nine #10 x 3/4” Phillips

screws to fasten the brace. Repeat this step for the other leg

mount brace on the second leg mount assembly.

12. Use the torx T25 driver to start two T25 x 3” torx screws into the pilot holes at the end of one of the seat supports in the leg assembly.

Stop as the points of the screws emerge from the other side of the seat support.

13. Hold the leg assembly upright and position one of the seat stieners so the

pilot holes in the end of the stiener line up with the emerging screw points

of the seat support. Use the torx T25 driver to drive the T25 x 3” torx screws

into the seat stiener.

Repeat this step to attach the other seat stiener to the other side of the leg

assembly.

NOTE: The support bar has small chamfers on the upper corners. Install the

support bar so the chamfers are away from the table top surface.

#10 X 3/4" Phillips Screw

Support Bar

Position a seat support over the legs and bolts with the bottom of

the support contacting the thicker portion of the leg end. Place a

3/8" at washer, 3/8" lock washer and 3/8"-16 hex nut on the end

of each carriage bolt and tighten nger tight.

NOTE: Installing the carriage bolts in this direction reduces the

risk of being scratched by the bolt end while using or moving the

assembled table.

Seat Support

3/8"-16 Hex Nut

3/8" Lock Washer

3/8" Flat Washer

3/8"-16 X 3 1/2"

Carriage Bolt

Leg Mount

#10 X 3/4" Phillips Screws

Leg Mount Brace

3/8"-16 Nylock Nut

3/8" Lock Washer

3/8" Flat Washer

3/8"-16 3 1/2" Carriage Bolt

Attach the other leg assembly to the other end of the seat stieners in the

same manner.

T25 X 3" Torx Screws

Seat Support

Seat Stiener

14. Return to the table top assembly. Orient the table top so that the top surface

is facing upward. Start one T30 x 3” washer head screw into each of the

corner pilot holes. Stop when the point of the screw emerges from the bottom

side of the table top.

15. Carefully turn the table upside down onto a padded work surface.

Start two T25 x 2 1/2” torx screws into the pilot holes in the center of the both seat supports. Locate the two angle braces. Start two

T25 x 2 1/2” torx screws into the pilot holes on the notched end, just enough to hold them in place.

16. Position one of the angle supports on the table top with the cutouts positioned over the angle brace mounts. Make sure the mounting

ange is facing out toward the edge of the table. Install nine #10 X 3/4" Phillips screws through the angle support and into the table top

rst.

17. Install four #10 X 3/4" Phillips head screws through the angle

support and into the angle braces, then install Phillips head

screws through the ends of the angle support and into the leg

mounts.

18. Repeat steps 16 and 17 to install the remaining angle support on

the other side of the angle braces.

Carefully li the table top assembly and position it over the assembled leg

structure and line up the emerging points of the washer head screws with

the appropriate pilot holes in the leg mount component of the assembled leg

structure.

Use the torx T30 driver to drive the washer head screws into the leg mount

until tight. Once the four screws are secured, the remaining washer head

screws can be inserted and driven into the rest of the table top pilot holes.

Aer the table top is secured, tighten all of the carriage bolts and hex nuts in

the leg structure.

Start the four corners T30

X 3" Washer Head Screws

Tighten hardware aer

table top is secure

Leg Mount

Position one of the angle braces so the notched end ts over the edge of the

angle brace mount near the center table top and the other end of the angle brace

contacts the center of the seat support where the two torx screws are started.

While one person holds the brace in place, another person should drive the torx

screws through the seat support, into the end of the angle brace. When the

outside screws are secure, drive the two started screws through the brace and into

the angle brace mount.

Install the remaining angle brace in the same manner.

T25 X 2/12" Torx Screw

#10 X 3/4" Phillips Screw

Angle Support with

mounting ange outward

Note: Install the screws from the center of the table,

alternating outward towards the ends of the table.

Keep the angle support pressed against the angle brace

when installing the screws.

Angle Brace

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

19. Carefully turn the table right side up. Start four T30 x 3” washer head screws

into the predrilled holes near the ends of one of the seat planks until the points

of the screws start to emerge from the other side of the plank. Line up the

points of the screws with the predrilled holes in the seat supports and use the

torx T25 driver to tighten the screws.

Place a T30 x 3” washer head screw into the predrilled hole in the center of the

seat plank and use the Torx T30 driver to tighten the screws, making sure the

screws are driven into the seat stiener.

Install the remaining seat plank in the same manner.

Move the table to the location where it will be used.

Seat Plank

T30 X 3" Washer Head Screw

Assembly and Replacement Parts

Right Leg

Le Leg

Leg Mount

Seat Support

Angle Brace

Seat Stiener

Seat Plank

Angle Support

Table Top Plank

Angle Brace Mount

Support Bar

Leg Mount Brace

Anova rcp6 Assembly Instruction

Brand: Anova

Model: rcp6

Category: Computer desks

Type: Assembly Instruction

Download PDF

report

Anova rcp6 Assembly Instruction

Anova rcp6 Assembly Instruction

Related papers

Other documents