2. Munters
  3. RPLP 115 R1.0 110777

Munters RPLP 115 R1.0 110777 Installation guide

  • Hello! I have analyzed the document describing the Munters RPLP1-V1 Lightning Protector. It provides detailed installation instructions and technical specifications. The device is designed to protect controllers from power surges, with specific instructions on wiring and power limitations. I'm ready to answer any questions you have about this device or its setup.
  • What is connected to the "INPUT" side?
    What is connected to the "OUTPUT" side?
    What is the maximum current through the RPLP-1?
    What should not obtain power through RPLP-1?
    What distance shold be kept between protected and unprotected wires?
P/N: 110777
RPLP INSTALLATION
P/N: P-RPLP1-V1 / C-RPLP1-V1
Place the Power Supply Lightning Protector close to the controller.
A proper ground must be supplied otherwise the protection will not be effective.
The side marked "INPUT" should be connected to the power source side. The side marked "OUTPUT"
should be connected to the power supply terminal side of the controller ONLY.
For example: If using a 24 VAC with the RPLP-1, then the voltage 24 VAC for the solenoid should be
wired from the "INPUT" unprotected side of the RPLR-1. This way any interference caused by the solenoid
will be filtered by the RPLP-1.
Protected and unprotected wires should not go through the same hole. Keep a distance of at least 1 inch
(2.5 cm) between protected and unprotected wires.
NOTE: The RPLP-1 is designed to provide protection ONLY to a controller. Make sure that devices such
as fans or motors operated by the controller do NOT obtain their power through the RPLP-1. Maximum
current through the RPLP-1 is 2.5 Amperes.
TECHNICAL SPECIFICATIONS
Power supply
Main voltage
single phase 115 Vac, 3 A
Main frequency 50/60 HZ
Ambient climate
Operating temperature range -10º to + 55º C
Storage temperature range -10º to + 70º C
Housing
Plastic housing with a screw on lid IP 56
Dimensions (LxWxH) 100 x 100 x 50 mm.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as waste. The controller, accessories
and packaging should be sorted for environmental-friendly recycling. The plastic
components are labeled for categorized recycling.
P/N: 110777
INSTALLATION
P/N: P-RPLP1-V1 / C-RPLP1-V1
Place the Power Supply Lightning Protector close to the controller.
A proper ground must be supplied otherwise the protection will not be effective.
The side marked "INPUT" should be connected to the power source side. The side marked "OUTPUT"
should be connected to the power supply terminal side of the controller ONLY.
For example: If using a 24 VAC with the RPLP-1, then the voltage 24 VAC for the solenoid should be
wired from the "INPUT" unprotected side of the RPLR-1. This way any interference caused by the solenoid
will be filtered by the RPLP-1.
Protected and unprotected wires should not go through the same hole. Keep a distance of at least 1 inch
(2.5 cm) between protected and unprotected wires.
NOTE: The RPLP-1 is designed to provide protection ONLY to a controller. Make sure that devices such
as fans or motors operated by the controller do NOT obtain their power through the RPLP-1. Maximum
current through the RPLP-1 is 2.5 Amperes.
TECHNICAL SPECIFICATIONS
Power supply
Main voltage
single phase 115 Vac, 3 A
Main frequency 50/60 HZ
Ambient climate
Operating temperature range -10º to + 55º C
Storage temperature range -10º to + 70º C
Housing
Plastic housing with a screw on lid IP 56
Dimensions (LxWxH) 100 x 100 x 50 mm.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing as waste. The controller, accessories
and packaging should be sorted for environmental-friendly recycling. The plastic
components are labeled for categorized recycling.
P/N: 110777
P/N: 110777
/